Question about Cars & Trucks

Open Question

Torque settings toyota estima head bolts - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
the terrier
  • 94 Answers

SOURCE: head bolts torque settings

according to the manual its 22NM or 16lb/ft

Posted on Oct 26, 2008

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota 80 series GLX auto landcruiser 1996 need head bolt torque a nd cam shaft torque settings


Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

Nov 22, 2014 | 1996 Toyota Land Cruiser

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

I am asking for torque specification of toyota tazz for cylinder head


head bolts are usually torqued in three stages. i believe the settings for yours are three stages of 25ftlbs. this means the first stage wll be 25ftlbs, the second 50ftlbs, and the third 75ftlbs. torque all head bolts in every stage.

Feb 12, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Hi i was wanting to now if anyone knows the Torque Settings for the head of a 1992 Toyota Windom V6. Thank you.


Cylinder Head Torque Sequence

Tightening torque:
12 sided bolt
Step 1 ..... 34 Nm (25 ft lb)
Step 2 ..... Tighten an additional 90°
Step 3 ..... Tighten an additional 90°
Recessed head bolt ..... 18 Nm (13 ft lb)

02e7fe1.gif

f910c49.gif

Oct 21, 2010 | Toyota Passenger Cars & Trucks

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Head bolt tourqe settings on a toyota cressida


Cylinder head bolt removal sequence


Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

Don't forget to rate this answer, Good Luck

Apr 24, 2010 | 1992 Toyota Cressida

1 Answer

1994 4runner, six cyl. putting rebuilt heads on, toyota head gaskets, new head bolts "tvs 10.9". Torqued bolts in pattern to 33 foot pounds. another 1/4 turn in the pattern. and into my next and final 1/4...


REMOVE 3 BOLTS MAKE SURE YOU HAVE THE RIGHT THREADS.IF BOLTS LOOK OKAY.YOUR BOLTS HOLES HAS DEBRIS OR OIL AND ANTIFREEZE IN THEM.OR YOUR BOLT HOLES IS STRIPPED.YOU HAVE TO REMOVE HEAD TO FIX THE THREAD PROBLEM.IF YOU HAVE NOT MADE THE FINAL TORQUE TO CRUSH AND SEAL HEAD GASKET THE. HEAD GASKET PROBABLY ALRIGHT.YOU HAVE TO LOOSEN HEAD BOLTS IN SEQUENCE BACK OFF A LITTLE AT EACH BOLTS.IF HEAD GASKET LOOK DAMAGE AT BOLT HOLES REPLACE HEAD GASKET.

Nov 13, 2009 | Toyota 4Runner Cars & Trucks

1 Answer

Cylinder head torque spec lucida estima 2.2


help cant get a manual for our car, change head but unable to find the torque setting for it, its a toyota lucida estima 2.2 thanks

Aug 30, 2009 | 1997 Toyota Previa

1 Answer

Toyota estima stated to overheat


yes it is the head gasket the compression is is leaking in to the cooling circut, take out the plugs and see if any is a orange colour if so to repair it you will have to buy a new head , gaskets head bolts other wise it will not last a 1000km

Jul 01, 2009 | 1992 Toyota Previa

1 Answer

The problem is the water is linking ender the water pump's bolt


Maybe you can find some guidelines in the following free download, good luck!:)

Contains:


Air Conditioner
Brakes, Wheels & Tyres
Cam belt
Central Locking Stuff & Alarms
Cooling System
Cylinder Head
Electrical System & I.C.E
Engine
Exterior Lighting
Fuel & Emissions System
Suspension & Steering
Transmission Systems

Also contains:

Estima Guide
Estima Owners Handbook

Download (~50MB): http://www.mediafire.com/?yx9wiypm6t2

May 20, 2009 | 2009 Toyota Venza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...