Question about 2004 BMW 325xi Sport

Open Question

Diagram for 2003 BMW 325xi serpentine belt? - 2004 BMW 325xi Sport

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
p_murfy
  • 63 Answers

SOURCE: need to install belt

i made this with paint. hope it helps. typically on a bmw the belt goes between the water pump and crank pulley to the tensioner; if this is a 99 to 06 ish 3 series and some 5 s you will be goode2f7e32.gif

Posted on May 03, 2009

Ad
blueextc3221
  • 15935 Answers

SOURCE: DIAGRAM FOR 2003 BMW 330i SERPENTINE BELT

ae31c6c.jpg
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 12, 2009

eitan
  • 291 Answers

SOURCE: diagram for serpentine belt for 2002 BMW 525i

4fb4db0.jpg
An image of a serpentine belt, hope this will help you,
Eitan.

Posted on Jun 10, 2008

  • 145 Answers

SOURCE: changing headlamps on 2003 bmw 325xi

I am assuming that you have a burned out head light bulb.
1) Open hood.
2) Working in back of headlight assembly, grasp rear of bulb socket (harness connector) and turn counterclockwise 90 degrees. Pull bulb out of headlight assembly.
3) Disconnect harness connector from bulb (gently pry, it's plastic)
4) Installation is reverse of removal. (Do not touch halogen bulb with bare skin-oils from hand will cause bulb to burn out.) Align tabs on bulb base to cutouts on rear of lens assembly. (Note bottom tab is wider than other two) Secure bulb by rotating clockwise 90 degrees.
Low beam bulb H9006
High beam bulb H9005

Posted on Jan 23, 2009

greg_margo
  • 1959 Answers

SOURCE: need serpentine belt diagram for 1994 bmw 325i

Below are diagrams for both the M44 and the M50 engines. On the M44, you may need to hold the tensioner in the retracted position with a drill bit or hex tool through the hole in the front of the tensioner. The belt tensioner is automatic so no tightening is necessary. Best of luck!
Greg

M44
8e7efb1.jpg






M50
701ceb4.jpg

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for the serpentine belt on a 2003 Rav4


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 02, 2012 | 2003 Toyota RAV4

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Timing belt for BMW 325xi


    There's no timing belt on a BMW u must mean serpentine or accesorie belt auto zone can give u a print out

    Apr 14, 2011 | BMW 325 Cars & Trucks

    1 Answer

    I need the alternator / fan serpentine belt diagram for my 2002 bmw 325I. Thankyou


    Look up your car on RealOEM.com. It shows the belt shape when installed.
    Good that you asked. I understand that it is physically possible to get it to fit with the alternator spinning backwards.
    I presume that you just replaced belts and pulleys. A 2003 would be about due.
    Be glad you don't have a 330 rather than a 325. The 330 is just enough tighter space to make the job about four times as difficult. (I have both).

    Mar 02, 2011 | 2003 BMW 325

    1 Answer

    DIAGRAM FOR 2003 BMW 330i SERPENTINE BELT


    ae31c6c.jpg
    Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

    Sep 12, 2009 | 2000 BMW 3 Series

    1 Answer

    Bmw 330d serpentine belt fitting


    Hey Andy a quick was to solve your problem is to locate a similar vehicle in a car yard, go have a look at the configuration and draw your self a quick diagram whilst your there.

    Sep 21, 2008 | 2001 BMW 330

    1 Answer

    Diagram for serpentine belt for 2002 BMW 525i


    4fb4db0.jpg
    An image of a serpentine belt, hope this will help you,
    Eitan.

    Jun 10, 2008 | 2007 BMW 525xi Sedan

    Not finding what you are looking for?
    2004 BMW 325xi Sport Logo

    Related Topics:

    1,156 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top BMW Experts

    Frankie B

    Level 2 Expert

    65 Answers

    Fred Sops

    Level 2 Expert

    272 Answers

    Doberman

    Level 2 Expert

    254 Answers

    Are you a BMW Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...