Question about 1998 Ford Windstar

Open Question

Who does sell de egr tube 1998 windstar - 1998 Ford Windstar

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 70 Answers

SOURCE: I have a 99 Windstar 3.8L Keep getting DTC PO401

Does the egr vavle open ? You will need to use a scanner to test the dpfe voltage when the egr valve is energized you should read around 3.5 4.00 volts. Also you could remove the vacume line from the egr valve and with the engine running you should see around 100 rpm drop in engine rpm at least this would indicate the egr valve is capable of flowing egr gases through the system to the cylinders.

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have p 1121 and a P 0401 codes on my 1998 ford windstar. are these related? what can I check? replaced the mass airflow sensor recently.




P1121 Ford Throttle Position Sensor Inconsistent with Mass Air Flow Sensor
http://engine-codes.com/p0401_ford.html no they are not related !
Are there any cracks in the rubber hose from air cleaner to throttle body ! That could cause the P1121 air entering after mass air flow sensor !
P1121 - Throttle Position (TP) Sensor Inconsistent with MAF Sensor The PCM monitors a vehicle operation rationality check by comparing sensed throttle position to mass air flow readings. If during key ON engine running self-test the comparison of the TP sensor and MAF sensor readings are not consistent with calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.
  • Air leak between MAF sensor and throttle body
  • TP sensor not seated properly
  • Damaged TP sensor
  • Damaged MAF sensor
Drive vehicle and exercise throttle and TP sensor in all gears. A TP PID (TP V PID) less than 4.82 % (0.24 volt) with a LOAD PID greater than 55% or a TP V PID greater than 49.05% (2.44 volts) with a LOAD PID less than 30% indicates a hard fault. P0401 - EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
  • Vacuum supply
  • EGR valve stuck closed
  • EGR valve leaks vacuum
  • EGR flow path restricted
  • EGRVR circuit shorted to PWR
  • VREF open to D.P.F. EGR sensor
  • D.P.F. EGR sensor downstream hose off or plugged
  • EGRVR circuit open to PCM
  • VPWR open to EGRVR solenoid
  • D.P.F. EGR sensor hoses both off
  • D.P.F. EGR sensor hoses reversed
  • Damaged EGR orifice tube
  • Damaged EGRVR solenoid
  • Damaged PCM
Perform KOER self-test and look for DTC P1408 as an indication of a hard fault. If P1408 is not present, look for contamination, restrictions, leaks, and intermittents

Mar 09, 2015 | 1998 Ford Windstar

1 Answer

Egr valve code on 2001 ford windstar


egr excess gas return $40 part easy to change takes 5 mins and its worth it. one tube it one tube out self explaintory to change

Jan 20, 2013 | 2001 Ford Windstar

1 Answer

Picture of egr valve and were it is located


dffc43b.jpg

Fig. 11: EGR valve and component mounting-3.0L engine


da251ab.jpg

Fig. 12: EGR valve and component mounting-3.8L engine

Removal:
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air inlet tube from the throttle body and air cleaner housing.
  3. Label and detach all vacuum hoses from the EGR valve.
  4. Label and detach any electrical wiring harness connectors from the EGR valve.
  5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  6. Remove the EGR valve mounting fasteners, then separate the valve from the upper intake manifold.
  7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm) on 3.8L engines, or to 106-159 inch lbs. (12-18 Nm) on 5.0L engines.
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 30 ft. lbs. (41 Nm).
  3. Connect all wiring or hoses to the EGR valve.
  4. Install the air inlet tube.
  5. Connect the negative battery cable.

Hope this helps (remember comment and rated this).

Jul 27, 2010 | 1995 Ford Windstar

1 Answer

I have a 99 Windstar 3.8L Keep getting DTC PO401 have replaced DPFE EGR Valve and EGR tube still keep getting Code PO401


Does the egr vavle open ? You will need to use a scanner to test the dpfe voltage when the egr valve is energized you should read around 3.5 4.00 volts. Also you could remove the vacume line from the egr valve and with the engine running you should see around 100 rpm drop in engine rpm at least this would indicate the egr valve is capable of flowing egr gases through the system to the cylinders.

May 30, 2010 | 1999 Ford Windstar

2 Answers

98 windstar p0401 error code


Best explanation...
http://www.obd-codes.com/p0401

Jan 20, 2010 | 1998 Ford Windstar

1 Answer

1998 Ford Windstar, no start with out pushing on throttle, some times not then, runs ok after it starts. have codes, PO340 & PO401


po401 is egr flow insufficiant ( the egr needs removed and cleaned also clean where it mounts to engine. po340 is camshaft position sensor A- bank 1 curcuit malfunction. it is a bad camshaft sensor.

Sep 20, 2009 | 1998 Ford Windstar

1 Answer

Winshield wipers quit working. fuse is okay


debe cambiar los carbones o escobillas del motor del limpia brisas, para lo cual debe desmontarlo o removerlo de su lugar.

Sep 17, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...