Question about 1993 Honda Accord

1 Answer

Distributor not putting out fire

I HAVE CHANGE THE DISTRBUTOR 2'S BUT MY CAR ISNT CRANKING

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,455 Answers

Dreaded main relay failure will cut power to fuel and distributor.

Posted on Sep 12, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 1991 honda civic clx wont start period after several OEM parts were installed

your timming might be off.

Posted on Jun 02, 2009

  • 306 Answers

SOURCE: car isnt getting any fire from plug wires changed

not sure but you can try cam or crank sensor.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 trailblazer 5.3 no fire change cam & crank sensor


if its got no fire and you changed your cam and crank sensor try replacing the ignition Coil then if it doesn't work replace the distributor cap and spark plugs and wires if that doesn't work then take the distributor cap off and replace the distributor Rotor if it still doesn't work replace the wires to the rotor if still i dosent work check your fuses but i assure you that should fix it.

Feb 24, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Iv try to start my 305 96 1500 vortex after putting an intake in i mark the bottom of the distributor alein # 1 on the distributotry to crank the truck discovered the distrbutor was not seated in the...


yes you can realign the distributor just remember it will not set all the way down until the oil pump drive lines up with the distributor shaft

Oct 02, 2011 | 1996 Chevrolet K1500

1 Answer

Its not firing weve replaced the relay switch the distributor and coil and it still isnt firing


You say Distributor if this actually has a distributor and not a coil pack remove the distributor cap and watch the rotor as you crank the motor. If the rotor isn't spinning your timing belt is broken, if it is, check the relay in the power distribution box under the hood as well as the fuse there and in the interior fuse panel to make sure they are all functioning properly.

Sep 17, 2011 | 1995 Toyota Corolla

1 Answer

I have a 87 toyota pickup the motor is not turning over enough to crank it i have replaced the coil distributor starter and battery


when you crank the engine you have to check if spark plugs fire if not maybe your crank sensor is bad, thats why car wont start, your distrbutor is turning when crancking? did you cnange distributor cap and rotor?

Feb 06, 2011 | Toyota Pickup Cars & Trucks

1 Answer

GOT THE FIRING ORDER WRONG


6 cylinder------ 1-5-3-6-2-4 distrbutor rotation clockwise-- straight 6
V6---- 1-6-5-4-3-2 distributor rotation clockwise
V8 with electronic ignition----- 1-8-4-3-6-5-7-2 clockwise
V8 points type--- 1-8-4-3-6-5-7-2 clockwise

May 15, 2010 | 1988 Chevrolet C1500

1 Answer

Need diagram fireing order


Since it has a distributor and it's a corvette I'm going to assume it's an old school small block Chevy.

1-8-4-3-6-5-7-2

Apr 17, 2009 | Chevrolet Corvette Cars & Trucks

2 Answers

No spark, just put in a new coil, distrbutor isnt dirty or wet, sombody told to check out the littl box's on the fender well, what are these to box's and what is there purpose? Mike 77 cj-5 304 3spd I...


I had the same problem with my 85 cj7 this week, I relpaced the ignition control module, plugs, wires, cap, rotor and the the coil; still had no fire to plugs. the problem turned out to be my distributor, replaced it today and she fired right up. Most likely it was the pick up module in the distributor that went bad.

Nov 30, 2008 | 1983 Jeep CJ7

1 Answer

Distrbutor to spark plug wiring


Hey there janandshane,

I've got a 91 Wrangler, lots of fun. Here's your info.

Viewed from above, front of vehicle on the right side, cylinder locations are:
6 5 4 3 2 1 for a six cylinder and 4 3 2 1 for a four Cylinder

The firing order is:
1 5 3 6 2 4 for the six and 1 3 4 2 for the four.

The distributor rotation is clockwise.

To find Top dead center (for wire to cylinder #1 on distributor), look for and line up the timing marks on the crankshaft (front of the engine).

Or, pull the #1 spark plug, stuff the hole with a cork or a rag. Slowly crank the engine until the cork pops out.

Pull the distributor off. The rotor is pointing where the plug for cylinder #1 should go. The rest of the wires go in the firing order clockwise.

That about covers it.

Remember: Good things come to those who rate. How about a nice FixYa?

Mike

Aug 16, 2008 | 1987 Jeep Wrangler

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...