Question about 2004 Ford Escape

Open Question

How to change serpentine belt on a 2004 ford escape

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

Ad
ewashmidas
  • 362 Answers

SOURCE: i need a diagram of 1999 ford contour serpentine belt

8f5f8d7.png
Top one is for a 2.0, with AC, bottom one is the 2.5 with AC.

8ebea63.png

Posted on Jan 24, 2009

localwonder
  • 6784 Answers

SOURCE: I need a serpentine belt routing diagram for a

HI. you can view an image of the routing by clicking the link below.

CLICK HERE FOR ROUTING.

Posted on Sep 21, 2009

  • 1757 Answers

SOURCE: serpentine belt diagram

CLICK on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/2002/make/ford/model/escape/2002_ford_escape_drive_belt_routing_diagram.htm

Posted on Mar 09, 2010

ZJLimited
  • 17970 Answers

SOURCE: NEED A DIAGRAM ON HOW TO REPLACE SERPENTINE BELT

2002 FORD ESCAPE - L4 2.0L 1989cc 122ci GAS FI N B
Belt Routing Diagram - Alt., P.S. & Comp.

9287cc5.jpg



2002 FORD ESCAPE - V6 3.0L 182ci GAS FI N 1
Belt Routing Diagram - Multiple Accessory

6cd5171.jpg


Hope helped (remember rated this).

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rout serpentine belt for 2004 escape


Label under the hood with picture of belt routing

If not there google a picture

WHY did it come off?

Have to know that BEFORE you ruin the next
new belt

Aug 13, 2014 | Cars & Trucks

1 Answer

2004 ford escape belt assembly


Most of the Fords I've owned including my 3 Escapes, have a diagram for the serpentine belt under the hood of the vehicle. Typically located on the frame above the radiator.

Jun 16, 2014 | 2004 Ford Escape

1 Answer

I need a serpentine belt diagram for a 2008 ford escape 3.0 v6


It is not that hard just remember to put the belt on where every pulley turns in the same direction .

Feb 18, 2014 | 2008 Ford Escape

1 Answer

2004 Ford Escape loud grinding noise, power steering stiff and belt covered w oil like substance?


Sounds like the power steering pump has failed.
You could take the serpentine belt off and check the pump pulley.

Jan 30, 2013 | 2004 Ford Escape

1 Answer

How do I remove an altinator from a 2004 ford escape.


Hello there,
To replace the alternator in your car:
Open the Escape's hood, and examine the belt-routing diagram on the fan shroud. This will show you the location of the alternator and the serpentine belt tensioner.
Pull the serpentine belt tensioner away from the serpentine belt with the serpentine belt tool far enough to allow you to dislodge the belt from the alternator pulley with your other hand.
Unplug the wiring harness from the back of the alternator by hand. Remove the ground harness from the alternator with the socket set.
Unbolt the alternator from the alternator bracket with your socket set. Lift the old alternator out of the bracket by hand.
Compare the old alternator to the replacement alternator before installing the replacement. Make sure they're both physically identical before continuing. If not, take them both to the parts store to match up a proper replacement.
Set the replacement alternator in the alternator bracket by hand. Bolt it in with the socket set. Plug the wiring harness in by hand and bolt the ground harness to the back of the alternator with the socket set.
Install the serpentine belt on the replacement alternator in reverse of how you removed it from the old alternator.
All the best. Elect_Comp

Sep 13, 2011 | 2004 Ford Escape

1 Answer

Need a diagram for a serpentine belt for a 2002 ford escape 24 v DOHC V6


I did find your manual but it did not detail the serpentine belt. Here it is just FYI.
2002 Ford Escape Owners Manual

Mar 28, 2011 | 2002 Ford Escape

3 Answers

2004 Ford Escape Electrical problem


This is a problem with the alternator. Diode rectifiers and voltage regulator replacement will give this baby a 14.2 voltage output. In this 3L V6 SUV removal of the alternator requires removing the right tire, the right axis and undercovering to reach the 6G alternator. It is a 133mm rectifier with a motorcraft, The serpentine belt is better removed from the bottom. Also keep a bucket on hand to recover the oil from the transmission.

Jan 11, 2009 | 2002 Ford Escape

Not finding what you are looking for?
2004 Ford Escape Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...