Question about 2003 Chevrolet Silverado 1500

Open Question

How to replace oil pressure sensor in suburban

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ronaldo_ross
  • 1056 Answers

SOURCE: 2002 chevy suburban oil pressure sensor location

If you look from under the vehicle you should see it, instead of from the top.

Posted on Nov 23, 2009

johndoe541
  • 784 Answers

SOURCE: I have a 2003 chevy suburban. I replace the oil

oil pressure. and all other sensors is ok

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of oil pressure sensor on v8 gasoline engine


Hi there,

The oil pressure sensor/switch is hidden behind the engine sight shield.

1. Remove the engine sight shield.
2. Disconnect the oil pressure sensor electrical connector.
3. Using J41712 sensor socket or equivalent, remove the oil pressure sensor.

wolfman304_73.gif

Cheers,


"Please rate this solution"

Aug 28, 2011 | 2003 Chevrolet Suburban 1500

1 Answer

1999 suburban 5.7L - Oil pressure gauge bounces back and forth between 40 and 50 pounds very rapidly


Replace the oil pressure sensor located near the oil filter. When this part starts to fail you will see your oil pressure gauge bounce all around

Jun 28, 2011 | 1999 GMC Suburban

2 Answers

Where is the oil pressure sending unit on a 2005 4X4 Suburban 1500 5.3 liter


Removal & Installation 4.8L, 5.3L & 6.0L Engine To Remove:
  1. Remove the engine sight shield. chevy_aval15_02-04_opcon.gif

  2. Disconnect the oil pressure sensor electrical connector. chevy_aval15_02-04_opsocket.gif

  3. Using J41712 sensor socket or equivalent, remove the oil pressure sensor.
To Install:
  1. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J41712 sensor socket or equivalent, install the oil pressure sensor. Tighten the sensor to 15 ft. lbs. (20 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.
8.1L Engine To Remove:
  1. Remove the engine appearance cover.
  2. Disconnect the electrical connector from the oil pressure sensor.
  3. Use a special socket such as J 41712 to remove the sensor.
To Install:
  1. If installing the old sensor, apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J 41712 or equivalent, install the sensor. Tighten the sensor to 22 lb ft (30 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine appearance cover.
prev.gif next.gif

Aug 05, 2010 | 2004 Chevrolet Suburban

1 Answer

I did a oil change on my 1994 gmc suburban w/5.7L and it started leaking oil on the back of the motor by the intake and the brass fitting for the oil pressure sensor. It is a steady leak and will lose all...


OK, does it appear that the oil pressure sensor is leaking through the plastic to metal seam (on the sensor itself)?

Have had an oil pressure sending unit go bad and leak on a 1990 Oldsmobile Cutlass Calais that needed to be replaced.

REMOVAL & INSTALLATION C1500 Suburban 1994
  1. Disconnect the negative battery cable and drain the engine oil.
  2. Disconnect the sensor electrical lead and unscrew the sensor. The sensor can be found on the top side of the engine, near the distributor. To install:
  3. Coat the first two or three threads with sealer. Install the sensor and tighten until snug. Engage the electrical lead.
  4. Connect the battery cable and fill the engine with oil.

Jul 14, 2010 | 1994 GMC Sierra

1 Answer

My suburban stalls and sputters out after running for about 15 minutes. I have replaced all the O2 sensors, plugs, wires, crank sensor, oil change, fuel filter, cap and rotor. What else could be the...


need to check the fuel pressure.and if its blowing black smoke,the fuel pressure regulator is bad.the fuel pressure should be around 65 pounds.

Mar 27, 2010 | 1999 GMC Suburban

1 Answer

Low oil pressur


It could be a bad oil pressure sensor or a bad oil pressure control valve which is located at the engine block where the remote oil filer line connects to. Start with the simple and replace the oil pressure sending unit and do a manual oil pressure test to ensure that your engine is making the right oil pressure needed to run your engine properly. Good luck and hope this helps. 60 PSI on cold starts and 42 to 48 PSI when at idle in gear.

Feb 22, 2010 | 1995 Chevrolet Suburban

1 Answer

Instructions to change oil pressure switch GMC denali xl


4.8L, 5.3L, 6.0L & 6.2L Engines
  1. If necessary, remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    0996b43f802053c2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the oil pressure sensor to 26 ft. lbs. (35 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. If necessary, install the engine sight shield.


Jan 18, 2010 | 2004 Chevrolet Suburban

1 Answer

2006 suburban oil pressure gauge fluxuating


Most likely it's the oil sending sensor, located beside the oil filter. You can change it, just be sure to have old newspaper or rags laying around the area where you will work, because a little oil will be lost. The part isn't expensive, for mine on a Ford Expedition was around $35 and took 5 minutes to change. Just un-plug the connector going to the sensor, and a larger wrench will be needed, large (7/8, 15/16) somewhere in that range of size.

Jan 06, 2010 | 2003 Chevrolet Suburban 1500

2 Answers

Low oil pressure on 2001 Suburban


your oil sensor comes on at less than ten psi, you may have internal engine damage how many miles on engine, any gum up inside engine, you can try to put on a high pressure high volume melling oil pump to try to help for the time being, but you may need to have it torn and repaired.

Aug 03, 2009 | 2003 Chevrolet Suburban 1500

2 Answers

I have low oil pressure in my 1994 chevrolet suburban


start by testing your oil pressure sensor, and then if not that drop your oil pan and the screen on your oil pump tube may be restricted. or change the oil pump could be weak

Jan 23, 2009 | 1994 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...