Question about 1992 Chevrolet Lumina APV

Open Question

3.8 Litre Throttle Body Removal - 1992 Chevrolet Lumina APV

Posted by on

  • Robert Haugh Feb 18, 2012

    Where can I find a diagram for this?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Throttle actuator control motor located on a 2007 chevrolet impala 3.0 litre


its on throttle body which is at the end of the rubber hose that comes from your air filter.. which usually means u have to replace throttle body since its all one assembly usually

Feb 28, 2015 | 2007 Chevrolet Chevrolet Impala LTZ

1 Answer

Throttle actuator A control system is stuck closed


This sounds like a very dirty throttle body. On the turbo cars it's pretty hard to get to the throttle body for removal and cleaning. I'm not sure about non-turbo.... Either way, a good throttle body cleaning should help out with this code.

Mar 12, 2014 | Volvo S60 Cars & Trucks

1 Answer

Throttle body sensor location 2005 uplander


the sensor is part of the throttle body and not replaceable here is the throttle body replacement instructions as you will have to replace the entire throttle body it is a very common issue with these
THROTTLE BODY ASSEMBLY REPLACEMENT

REMOVAL PROCEDURE
  1. Remove the air cleaner intake duct.
120434113
  1. Disconnect the electronic throttle control (ETC) electrical connector (1) from the throttle body (2).
113356645
  1. Remove the heater pipe nut at the throttle body.
  2. Remove only the heater inlet pipe.
113356646
  1. Remove the nuts and the bolts from the throttle body.
  2. Remove the throttle body assembly.
  3. Remove the throttle body gasket.
  4. Clean and inspect the throttle body gasket mating surfaces.
NOTE: Do not use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to the gasket surfaces and throttle body assembly may result.

Use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.

INSTALLATION PROCEDURE
113356646
  1. Install a new gasket, if necessary.
  2. Install the throttle body assembly.
  3. Install the throttle body nuts and the bolts.
NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the nuts and the bolts to 10 N.m (89 lb in) .
113356645
  1. Install the heater inlet pipe.
  2. Install the heater pipe nut to the throttle body.
Tighten the nut to 25 N.m (18 lb ft) .
120434113
  1. Connect the ETC electrical connector (1) to the throttle body (2).
  2. Install the air cleaner intake duct.

Feb 03, 2014 | 2005 Chevrolet Uplander

1 Answer

2003 gmc envoy xl 4wd 5.3 litre idles low and stalls mainly when parking but sometimes also when coming to a stop...have replaced many parts already.


Hello: Get some carburetor cleaner, remove rubber tube going to the throttle body. Spray cleaner on rag and open throttle plate and clean all black stuff (carbon) off the throttle plate and the inner bore of the throttle plate. Make sure its clean, You can spray some in the throttle body but not very much as too much and you cab blow the engine up. If build up is bad (carbon) go to Auto Zone and purchase a small brass bristle brush to help remove carbon.

Oct 24, 2011 | 2003 GMC Envoy

1 Answer

Idles but wont throttle 1999 Suzuki esteem wagon 1.6 litre


throttle wire at throttle body either broken ,off, or throttle boy butterfly stuck from carbin build up,

Feb 11, 2011 | 1999 Suzuki Esteem

1 Answer

How do you set the throttle position sensor on 1999 jeep grand cherokee 4.0 litre


That sensor is not adjustable. It slides onto the throttle shaft and is screwed in place to the throttle body. Idle speed is controlled by the computer by adjusting air flow through the idle air control valve. If the idle is too high (you did not say) first clean the throttle body bore and plate, then if necessary remove the control valve, cleaning out the passage in the throttle body and carefully cleaning the valve itself, without turning the plunger. If that does not help, you will need to do electrical testing on that and other components to find out what's going on as well as checking all vacuum hoses attached to the engine for cracks or leaks.

Nov 12, 2010 | 1999 Jeep Grand Cherokee

1 Answer

THROTTLE STICKS HAS HAPPENED A COUPLE OF


Have you tried cleaning the throttle body. Use throttle body friendly cleaner as it has a special coating that you do not want to damage it. Clean the sutt out real good where the butterfly valve is, inside and outside.

Aug 10, 2009 | 2000 Chevrolet Silverado

2 Answers

HIGH IDEL


sometimes the gasket under the trottle body goes bad. spray carb cleaner at the base of the trottle (not down into it) body while the engine is running. if the idle changes your on the right track. its an easy gasket to change.

Jan 08, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
1992 Chevrolet Lumina APV Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...