Question about 1995 Chevrolet Blazer

Open Question

What size wrench to remove the fuel filter 95 blazer

Is the filter metric

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
juststinks
  • 98 Answers

SOURCE: 95 S10 blazer won't start

check the EGR valve. it might be dirty in side with carbon. DONT GRINE OFF GASKET SCRAP IT OFF.

Posted on Apr 22, 2009

Ad
  • 3 Answers

SOURCE: 95 blazer with vortec spark is fine fuel is not

you have to put a guage on it to find out the pressure it may kick on but not enough pressure

Posted on Apr 28, 2009

Molson02536
  • 3854 Answers

SOURCE: 95 chevy blazer tank removal

Park the vehicle in a place where you’ll have plenty of room to work. If you have access to a lift, that would be great.
Relieve any fuel pressure by removing the fuel cap. Disconnect the negative battery terminal. Pre soaking any required bolts/nuts with WD-40 prior to the job will help also. There are 3 lines and 2 electrical connectors to be removed from the fuel pump, and the filler and vent hoses that need to be removed from the back of the tank. There was also a small hose on the front part of the tank that needs to be removed, but we didn’t see it until we actually started lowering the tank. Just remember where everything hooks back up. Label the lines, if needed take picture with your cell phone.

Start by removing the skid plate, Once the skid plate is off, you’ll have access to the straps that hold the fuel tank on. The forward ******** the Blazer will pretty be rusted and not very stout. It's basically formed as a strap that ended in a threaded bolt and in most will end up breaking trying to remove it. Supported the tank with a floor jack with a transmission removal assembly on it.

You easily fixed the broken strap problem by welding a bolt to the strap. Once all the straps were loose, lower the tank just enough to get better access to the lines and connectors leading to the fuel pump. There is not much room to get in there on a Blazer. 
Once the tank is off, it’s a good time to look around in that area to see if there are any other problems that may need to be addressed.

If you are going to replace the fuel pump here's how to do it. Before removing the fuel pump, be sure to clean off all the junk that has collected around it. 
Replacing the float and sending unit is fairly simple. Just pay attention to how the old parts are removed, and install the new parts in reverse order. Be sure to get the wiring routed correctly and install the new seal that comes with the kit. The sock filter on the bottom of the pump was just a little bit clogged, so we made a trip to the auto parts store to get a new one. Luckily they had one that would match up. 
While we had the tank off, siphoned what fuel was in there and cleaned out the tank really well. 

The installation is basically just a reverse of the removal. Be prepared to take quite a bit of time for this project. It took much longer that I expected. Somewhere around 6-7 hours, but that’s including several little problems, getting propane for BBQ lunch, and making a trip to the parts store for a new sock filter for the bottom of the pump. And Mom and dad showing up.

Good luck and hope this help

Posted on May 26, 2009

dennymulford
  • 1055 Answers

SOURCE: allen wrench size to fit caliper mounting bolt

some are 7/16 and some are 3/8 amd some are torx

Posted on May 30, 2009

Molson02536
  • 3854 Answers

SOURCE: '95 blazer wheres my fuel filter?

The fuel filter is on the drivers side in the frame rails just forward of the transmission cross frame. You can re move it with simple tools, the filter is held to the frame by a plastic mount that is also mounted to the frame. The filter mounts also secure two more lines which un clips when the mount is off the frame. 
It's easier if you loosen the fuel line first with the fuel filter mounted to the frame. NO special tools to disconnect the fuel line's.
Good luck and keep me posted. 

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel filter


The new filter is cheap and a vary good idea to replace 5 or 6 years it will save the intank pump from working way to hard to pump fuel to the intake manifold injection system . Alot of fuel pumps go bad because the inline filter is restrected . The filter is located under the drivers door on the inside of the frame rail close to the floor board look for the fuel line that comes from the tank pump and the line that goes up to the engine compartment area so it will have a metal line on bolth sides of it that has a connecter . What you need is open end wrenches or flare nut wrenches just make sure they are the correct sizes . You need to lossen these connections . The filter has a welded nut on it the line has a compresstion fitting that is part of the line and smaller then the welded nut on the filter but will not slide off the line because the line is flared so it will seal againest the filter . I would recomend getting the new filter first note the arrow on it this is the derrection the fuel must flow from the tank to the engine the arrow points to the engine and you can also know what size the welded nuts on the filter are also you can see what you are looking for under the vehicle . The fuel line nut is likely 5/8 s but may be metric 14 or 15 mm . The problem is you will not have a lot of room to work the filter is mounted to the frame with a strap type fastener and can be removed but if you can lossen the fittings with out removeing this first it will be easyer . Wonce the fittings are lose you will need to lossen or remove this strap to slide the new filter in place . And be ready for gas to leak out you will get 6 or so ounces of fuel that will spill on you and the ground . I hope i didn't make sound hard to do .The hardest part is breaking the lines free so make sure you have the right size wrenches and the limited room to get at the fittings GOOD LUCK

Mar 09, 2012 | 2002 Pontiac Montana

1 Answer

Where is my fuel filter located?


Check under vehicle follow the fule line from the tank

For replace it, lift drivers side of vehicle safely, remove battery ground cable, Using metric wrenches, remove one side of the fuel filter hex nuts( have a large drain pan underneath). On the other side of the filter are 'quick clip' connections. Grasp the ears of the connections and squeeze together and then push the connection toward the old filter and then quickly pull apart.Reverse the procedure.

I hope this helps (remember rated and comment this).

Aug 21, 2010 | 2003 Chevrolet Blazer

1 Answer

Tools needed to replace fuel pump on 1996 blazer?


A 10mm wrench to remove the bolt holding the bracket to the frame. 15 or 16mm wrench for the line going into the filter, 17mm or 18mm for the fitting on the fuel filter.

Jun 09, 2010 | 1996 Chevrolet Blazer

2 Answers

HOW DO I CHANGE THE FUEL FILTER 2000 CHEVY BLAZER


Disconnect ground battery cable, lift car safely, using two metric wrenches loosen the hex nuts on one side slowly to relieve pressure and drain into a large pan. Finish removing the hex nut.

Slide out of holder if you can. On the other side is a 'quick clip' connector; these are tricky. Grasp the ears and squeeze tightley and while doing this push in the connector and then quickly pull it apart. It may take a few trys. Just use your fingers if you can try. Installing it is the reverse but much easier.

Mar 03, 2010 | 2000 Chevrolet Blazer

1 Answer

What size wrench to remove brake calipers


Usually about 9/16. It should be SAE not metric, but if the standard is slightly loose, then you may be best off switching to metric socket.
You can go to autozone.com and register for full free online repair manual for your car. With everything you could need.

Dec 12, 2009 | 1999 Pontiac Grand Am GT

1 Answer

How can do i do a tune-up in 2000 chevy blazer ls 2wd


no tmuch to due, replace spark plugs, air filter. the fuel filter is the hardest, its under the vehicle. if you plan on replacing it, becarful, you will get gas running down your arms into the your arm pits. (this is burn) so becarful during this replacement.
you'll need "line" wrench to replace this filter, do not try removing the filter without a line wrench, by using a regual wrench it might be very tight to remove and a regual wrench will round off the nut where a "line" wrench will not. If you round off the fuel line nut, stop and tow it to your nearest dealership. they will have to replace the WHOLE fuel line.

Nov 03, 2009 | 2000 Chevrolet Blazer

2 Answers

2005 grand caravan ? size allen wrench to remove rear calipers


6 mm to small 8 mm to big, how about 7 mm would you not think ??

Aug 16, 2009 | 2002 Dodge Grand Caravan

1 Answer

Sideview Mirror Replacement


Try either an open end wrench or 1/4" drive socket, possibly 10 mm or 12 mm ( metric ) . Forget using needlenose pliers. Hope this helps

May 10, 2009 | 1996 Chevrolet Blazer

1 Answer

Fuel filter


its not too uncommon for the lines to be extreamly tight due to corrosion and other factors...enough said.get some GOOD penetrating oil (not wd-40)spray it a couple of times throughout the day,let it sit all night and the most important thing is that you use the correct kind and size wrench you need Line Wrenches get a good one not a cheepo,the filter should have a 13/16 or so hex to put a good open end wrench and hold it as you use the line wrench on the line end.hope it works have a good day DB

Feb 20, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...