Question about Chrysler Cars & Trucks

Open Question

2011 Chrysler 200.Low tire warning.

Can not get a proper anawer from service dept.What is the pressure alarm setting? Is the setting adjustable? Does the warning reset after proper pressure is applied or do you have to reset by dealer?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: 2007 grand prix tire pressure monitor reset

After you adjust the tire presuure you must drive the vehicle for a few miles then look at the gage again/ you can also disconnect battery for 15-20 minutes. Please rate my response Thank you very much

Posted on Jan 28, 2009

  • 1 Answer

SOURCE: LOW TIRE PRESSURE WARNING LIGHT

Turn ignition to run position,go to fuse panel right hand of vehicle,push and hold reset button for 5 seconds,low pressure light will flash 3 times,start car it should turn off the low pressure light.

Posted on Jan 29, 2009

pingman37
  • 58 Answers

SOURCE: Tire pressure light is on

You cannot reset them,Make sure that you check the pressures in the tires. The Infiniti Tire Pressure Monitoring System is designed to trip the warning light anytime the pressure in any of the tires drops below 29 psi. At 29 psi it really won't look like the tires are low. You could have one tire at 29 or 28 causing the light to stay on all the time. Check your pressures, set at 34 or 35 to be safe, or whatever pressure the tire is recommended to be. Not all infiniti vehicles with TPMS have the display that shows the pressure in each tire. If the pressures are above 29 psi, Then there could be an issue with one or more of the sensors. If you have the tires replaced you will have to have the sensors relearned at the dealer. Tire rotations do not require the same. 

Posted on May 08, 2009

  • 1 Answer

SOURCE: How do you reset a low tire pressure warning on a 2008 Jetta?

Reset the tire pressure warning, same as you would any service issue. Insert key in ignition, hold wrench button and min button, then start engine.

Posted on Jun 08, 2009

mitchbtu
  • 121 Answers

SOURCE: oldsmobile alero resetting low tire pressure

when you open the drivers side door you need to remove a panel door that will allow you to access the fuse box locate the the red button to the left side and press it a couple of times until you see your tire light flash after it starts to flash hold it in for a couple of seconds and you will hear a chime 4 times and you light will be reset you need to have your key turned on but not running to be able to do this.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low beam headlight adjustment on 2011 Chrysler 200


How to Adjust Car Headlights Level your car. Start by removing any excess weight from the trunk of the car. Also, ensure that the tire pressure in all tires is at the manufacturer's recommended levels. If possible, have somebody sit in the driver's seat, and that the gas tank is half-full. As well as this, check that your headlight aim adjustment wheel (if fitted) is at the zero position. Position your car. On level ground, park 10 to 15 feet (3.0 to 4.6 m) from a dark wall or garage door, with the front of the car aimed at the wall. A paved parking lot or level driveway is best Turn the headlights on. Do not use your high beams or fog lights. Mark the horizontal and vertical center lines of the headlight beams with masking tape to make two T's on the wall or garage door.Make sure the lights are level. Place a carpenter's level between the two marked center lines to see if they are even. If they are not even, use a tape measure to measure how far up the wall the lower mark is and lower the other center line marker to the same height. These center lines should be no higher than 3.5 feet (1.1 m) from the ground.Back your car exactly 25 feet (7.6 m) from the wall or garage door. Don't estimate the distance! Use a tape measure to make sure you are the proper distance away from the wall. Turn off the headlights. Remove the trim ring from around the headlights and locate the adjusting screws. These screws are typically found adjacent to the headlight, though some manufacturers put the screws in the engine compartment, behind the the headlights. The horizontal adjuster and the vertical adjuster should be marked.
  • Always defer to the specs in the owner's manual-Adjust each headlight separately. Block one with a sweatshirt or other object while adjusting and testing the other, since the light-bleed can make it difficult to distinguish one from the other. Have a helper sit in the driver's seat while you do the adjustments, to turn the lights on and off while you make the proper adjustments

Sep 30, 2016 | 2011 Chrysler 200

1 Answer

The tire light flashes then stays on 2011 Dodge Grand Caravan What could that mean?


Diane, it is sensing low air pressure in one of the tires, or faulty sensor. check air pressure in tire and fill to specification.
Check the attached links for more info,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Why Is My TPMS Light Flashing It Could Be Time for New Sensor Kal Tire

Dodge Chrysler Jeep Fiat TPMS Tire Pressure Monitoring System Relearn...

http://forum.chryslerminivan.net/showthread.php/15281-Tire-Inflate-Light-Comes-on

Tire Pressure Warning Light

Mar 12, 2016 | 2011 Dodge Grand Caravan

1 Answer

Why does tire light stay on 2011 Toyota?


Reset the Tire pressure monitoring system light. The reset button is located under the steering side under the finish panel. You have to bend down to see the button.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON

Jul 23, 2014 | 2011 Toyota Highlander

1 Answer

2005 grand Cherokee service tire pressure system


I found this on another site, it may help to understand what is happening, I also saw that there is a problem with the valve stems cracking since they're made out of aluminum and causing that problem. Here's the explanation provided on another site:

RodneyJ Answered 6 years ago
If a customer with a 2005 or later DaimlerChrysler vehicle equipped with Tire Pressure Monitoring (TPM) is concerned that the TPM lamp is on continuously, please be sure to inform the customer that the system is in place to warn of a low tire pressure situation, and a system diagnosis may not be required. The customer should be aware of the following: The Tire Pressure Monitoring (TPM) System will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure (the placard is located on the drivers side B-pillar).
The tire pressure will vary with temperature by about 6.9 kPa (1 psi) for every 6.5 Degrees C (12 Degrees F). This means that when the outside temperature decreases, the tire pressure will decrease - the customer should adjust his tire pressure for this decrease in pressure - please refer the customer to his vehicle owner's manual for information on how to properly inflate his vehicle's tires. The tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure.
The TPM System will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects.
The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the TPM warning lamp to be turned off. The system will automatically update and the TPM warning lamp will extinguish once the updated tire pressures have been received. The vehicle may need to be driven for up to 10 minutes above 25 kph (15 mph) to receive this information.


FOR EXAMPLE:

A 2006 300 has a recommended cold (parked for more than 3 hours) placard of 207 kPa (30 psi).

If the ambient temperature is 18 Degrees C (65 Degrees F) and the measured tire pressure is 186 kPa (27 psi) the TPM lamp will be OFF.

IF NOTHING IS DONE TO THE AIR PRESSURE IN THE TIRES and the ambient temperature drops to 20 Degrees F (-7 Degrees C) while the vehicle is parked, the approximate tire pressure will be 157 kPa (23 psi) and the TPM lamp will be ON.

IF THE VEHICLE IS DRIVEN TO REACH NORMAL OPERATING TEMPERATURE

WITHOUT ADJUSTING THE AIR PRESSURE and the ambient temperature stays at -7 Degrees C (20 Degrees F), the approximate tire pressure will rise to 186 kPa (27 psi) and the 1PM lamp will be ON.

To turn the TPM lamp OFF the tires must be inflated to the vehicle recommended cold placard pressure.

In order to properly maintain vehicle tire pressure, please refer to the owner's manual for additional information regarding tire inflation.

NOTE :Tire pressure should always be set based on cold inflation tire pressure (defined as the tire pressure after a vehicle has not been driven for more than 3 hours - and in outside ambient temperature).

Seasonal temperature changes will affect tire pressure, and the TPM system will monitor the actual tire pressure in the tire.
If a diagnosis of the system is required (for example, the lamp did not extinguish, or the lamp is flashing), please refer to service information available in TechCONNECT for additional information for TPM diagnosis. Please be aware that if the Wireless Control Module (WCM) is replaced, the TPM placard values may need to be reprogrammed. The TPM placard values do NOT need to be updated if the WCM has NOT been replaced, the TPM placard values are properly set at the factory.

Jan 23, 2014 | Cars & Trucks

1 Answer

On 2007 Chrysler Pacifica - When the car is started, the alarm sounds and the service tire system soon light flashes 8 or 9 times and then remains on. Do I have worn out batteries in the sensors or ??? And...


Start with making sure the tires have correct air pressure in each tire, then go from there.The alarm is a warning there is an issue with your tires. Low air can set it off or an imbalance. If the treads are worn due to alot of mileage, check those. Tire blowouts are no fun and can cause a serious accident or damage to your vehicle like bent rims. Tires are sometimes 'weighted' when rotated. There may be uneven wear if they do not get rotated per tire manufacturer's recommendation.

Sep 19, 2013 | 2007 Chrysler Pacifica FWD New Cars

1 Answer

Tpms light on, dic indicated low tp fr, inflated to proper pressure,tpms stays on, dic wont update


TPMS - TIRE PRESSURE MONITOR WARNING LIGHT
NOTE: Tire pressure rises and falls depending on heat caused by vehicle's operation and the outside temperature. If outside temperature is low, the air inside the tire may cool, causing a lower tire inflation pressure. This may cause the low tire pressure warning light to illuminate.

When the tire pressure warning light comes on, immediately check the air pressure of all tires and adjust to the specified pressure. Make sure the warning light goes off. If the warning light stays on or flashes, there is a malfunction in the TPM system. See appropriate manufacturer service information.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 13, 2012 | Cars & Trucks

1 Answer

What does an ! in a circle mean with ( ) around it


This (!) symbol is your TIRE PRESSURE MONITORING SYSTEM (TPMS) warning light.
The manual has this to say about it:
This system monitors tire pressure. if the low tire pressure warning light illuminates, check the tire pressure in all four tires. Adjust the low tire pressure to the recommended cold tire pressure shown on the Tire and Loading information label located in the driver's door opening. After tire pressures are adjusted, the vehicle will need to be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light.

Mar 02, 2011 | Nissan Pathfinder Cars & Trucks

2 Answers

What does it mean when it says check the tpm system?


The TPM System is the Tire Pressure Monitor. Each wheel will have a tire pressure sensor that monitors the tire pressure of each wheel and send that information to a computer. If the computer is not receiving the proper information it will let you know. If the low tire light is on and not flashing than it may be something as simple as a low tire. The proper tire inflation will be inside the drivers front door on the build sticker.

If all the tire pressures are o.k. than you will need to get the TPMS scanned to see why it is not working. Chryslers are pretty common for pressure sensors to fail.

Sep 27, 2010 | Chrysler 300 Cars & Trucks

2 Answers

Overhead console warning


the air pressure in the spare tire is low add air to proper pressure and it will reset itself spare pressure low the perform service could also be for tire but check owners manual for reset service reminders or have scanned at an auto store sum,such as auto zone / advanced auto do it for free and can reset the code via scanner

Oct 21, 2009 | 2005 Jeep Liberty

1 Answer

How do you reset low tire light


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 20, 2009 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...