Question about Toyota Celica

Open Question

P0340 celica intermitant fault car jurks and engine light comes on,fault code p0340 had new cam position senser fitted problem still not fixed,occurs most oftern when engine is hot and in slow moving traffic,let engine fully cool down runs fine.read lots of identical desciptions of foult never fould a solution

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: 03 Taurus with DTC P0340, P1336

I would think it would be just the Camshaft Position Sensor.I looked up the codes and they say pretty much the samething.


P0340 Ford Camshaft Position Sensor Circuit Malfunction


P1336 Ford Crankshaft/Camshaft Sensor Range/Performance












Posted on Jan 18, 2009

  • 82 Answers

SOURCE: car gets hot when i idle..

change your thermostat it may not be opening all the way

Posted on Feb 25, 2009

  • 4 Answers

SOURCE: My 1998 Peugeot 406 starts okay when cold but

I have 1996 Peugeot 406 (1.8 16v) and it's ignition coil pack was broken and the starting was difficult when the car was warm.  

Posted on May 08, 2009

localwonder
  • 6784 Answers

SOURCE: most common cause for code P0340 of 95 Ranger

Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

Posted on May 21, 2009

97F350diesel
  • 1326 Answers

SOURCE: Jaguar xk8 1997 The throttle

Pull up your codes to see what the are for and then you can begain to diagnose. here is a link to the codes. The 1122 is a TPS problem and the 1222 is a traction control issue. More then likely there is some sort of issue with the TPS causing your performance by the ECU not being able to detect the position of the pedal. Save this link for future trouble codes
http://www.obd-codes.com/trouble_codes/jaguar/

Posted on Sep 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

PONTAIC G6 2008 2.4 CAM POSITION SENSER PROBLEM HOW TO CORRECT


Buy the sensor from the car dealership. The sensors at auto stores are inferior and sometimes do not work properly.

Jul 07, 2014 | 2008 Pontiac G6 Sedan

1 Answer

P0340 Problem Code for 03 Jeep Liberty


code p0340 refers to cam shaft position sensora bank 1-circuit malfunction===causes --wiring Cam sensor---ECM. The only connection is the ECM to both units so they may have unpluged the ECM to service the air bag problem. IT could be as simple as using a code reader to reset the CPU. I may also be a coincedence and there may be a fault in the cam position sensor.. I would discuss the matter with the dealer service department to determine what is what.

Oct 23, 2013 | 2003 Jeep Liberty

1 Answer

My 2002 pt cruiser died while I was driving first the oil light came on then it just died! I just had the oil changed 3 days prior to it dying some of the codes I received were 0340 1684 1685...


P0340 is cam position sensor. P1685 is for the key(has a chip in it) P1684 is battery has been disconnected. If the engine will still crank then codes P1684 & P1685 are probably old codes. So if the car will still crank, lets forget about those codes and focus on P0340 A bad cam position sensor will cause the engine to die and not allow it to start back up. Replace the cam position sensor and clear the code and the car should start up.

Oct 16, 2012 | Cars & Trucks

1 Answer

Bmw z3 2.5i CODE p0340


The code is for the cam position sensor for the intake cam shaft.
You can clear the code and it may not come back. If it keeps coming back you might want to replace the sensor and double check the connections where it plugs in to the harness. Hopefully this will fix the problem.
Let us know if this helps, Robert

May 16, 2012 | 1999 BMW 323 Series

1 Answer

I HAVE A 2006 CHEVY AVEO, LESS THAN 80 MILES AGO IT WAS RUNNING BAD AND LEAKING OIL. CHECK ENGINE LIGHT ON AND CODE P0300. THE VALVE COVER GASKET WAS LEAKING OIL INTO THE SPARK PLUG DWELLS. REPLACED THE...


when run with a misfire, the cat will get loaded up with fuel, it takes awhile for it to burn out, and a code may set, on some occasions it ruins the converter, try clearing it and running it

Oct 13, 2010 | 2006 Chevrolet Aveo

2 Answers

CHECK ENGINE LIGHT ON CODE P0340


code P0340 which stands for camshaft position sensor fault.
what engine is this? if it is a 4 cylinder this can be caused by a loose timing belt.

Jul 09, 2010 | 1996 Toyota Camry

1 Answer

03 Taurus with DTC P0340, P1336


I would think it would be just the Camshaft Position Sensor.I looked up the codes and they say pretty much the samething.


P0340 Ford Camshaft Position Sensor Circuit Malfunction


P1336 Ford Crankshaft/Camshaft Sensor Range/Performance












Jan 18, 2009 | 2003 Ford Taurus

1 Answer

RICH


DTC (diagnostic trouble code) P0340 is indicating a fault has occured in the camshaft position sensor system of the cars' electronic engine control system. DTC P0717 is for a transmission input turbine shaft speed. Typically these codes are unrelated. Both the sensors are variable reluctance devices. They have no moving parts and as such are robust and not usually prone to failure. But they can and do fail. Are either codes "hard" faults or are they in the continous memory of the computer? Does the P0340 clear itself when the engine is shut off and restarted? Can you cause the P0340 to reoccure just by starting the engine and with out driving it and revving the engine to 1500 to 2000 rpm for 1 to 2 minutes while in Park? The P0717, when cleared should only reoccure when the car is driven. If the camshaft position sensor has been replaced and still the same code occures make sure you have the correct information as to the meaning of this code in regards to your particular model year and engine. Does the engine have a camshaft position sensor for each camshaft? If so what is the DTC code for the other camshaft position sensor. Yes, the engine's computer (ICM, PCM, ECM, all terms for same thing) could be faulty but in most cases this is not the problem. Does the transmission seem to shift properly? You probably won't notice a differnece in the way the engine runs if the camshaft position fails due to the default stratagy used in the ICM. Wiring would be my next area of concern. Does the wiring for the camshaft position sensor and the transmission sensor go through the same wiring harness and could you have a poor connection at some point in that harness? Inspect the wiring and the hardshell connectors throughout the harness. Let me know what you find out. Thanks

Sep 28, 2008 | 1994 Cadillac DeVille

1 Answer

2005 dodge diesel codes!


Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Sep 27, 2008 | 2005 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...