Question about 2008 Dodge Avenger

1 Answer

Diagram I am installinf a front bumper cover, driver fender and head light on a 2008 dodge avenger i need the diagram for this installment. Could you please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Check online tech sites you will have to pay in order to download the documents and it is usually anywhere between 65.00 and 125.00 dollars to do so. Here is a good site http://www.autoeducation.com/repair_manuals/Dodge-Avenger.html

Posted on Jun 02, 2009

6 Suggested Answers

  • 1 Answer

SOURCE: 2008 dodge avenger. Will not move out of park.

i have a 2008 dodge avenger in i cant move it out of park

Posted on Oct 22, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

sandman357
  • 236 Answers

SOURCE: Brake Fluid for 2008 Avenger

it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Posted on Feb 22, 2010

Testimonial: "Quick response, guided me in the right direction. Thanks!"

  • 1 Answer

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Posted on Feb 23, 2010

  • 31 Answers

SOURCE: i need a diagram of

There should be a diagram under your hood on the radiator support.

Hope this helps

Posted on Aug 07, 2010

  • 4977 Answers

SOURCE: I need a diagram for

the belt routing should be under the hood or on the upper rad support.some of these are on the timing cover in the form of a placard.if it is missing then draw the routing of the belt before you remove it making sure you draw all the pullys and how the belt goes around them.or you can get the routing from the parts store you bought the belt from.or the library has books that will show it for your car and motor

Posted on Mar 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will interchange specifically front fender and bumper cover


Mary, 1998 to 2004 fender and bumpers will interchange, some bumpers had fog lights. press the helpful button

Feb 16, 2016 | 1998 Dodge Intrepid

1 Answer

Will a 2010 dodge avenger sxt right passenger side fender fit a 2008 Dodge avenger sxt model both are 4dr sedans


Ebay part. It will list all vehicles the fender will fit. Kind of a "reverse" interchange book, but it works.

Mar 11, 2015 | Dodge Avenger Cars & Trucks

3 Answers

How do I change right front head light


The 2008 CTS is the same as my 2009 CTS.
To access the any of the bulbs, you need to remove the bumper/grille assembly.
I just did mine and installed some aftermarket HID bulbs.
If you have some skill and patience, it will take you around an hour.
I'll try to remember all the steps, but I did find a video on youtube that shows it very well:
Remove the long plastic cover over the radiator, by unscrewing the 6 plastic clips. There some rubber molding attached, but you can just flip the cover over on top of the engine.
This exposes 2 10mm screws that can be removed - they'll look like they are attached to the grille. Don't remove them yet.
If front of each front tire in the edge of the wheel well, there are two plastic pins. The pins are actually two pieces, pry the center piece straight out about a quarter inch, then the whole pin can be popped out.
Under the front lower edge are 5-7 similar clips that need to be removed the same way. There about 15-20 of them under there, but you don't have to remove them all. I recall that two of them are upside down.
Now he scary part.... back to the wheel well. Get a flashlight. I recall the inner fender is under the bumper edge; it needs to be pulled out from behind the bumper. Then pull the inner fender backwards from the bumper; it's very stiff, but you need to pull it about 3/4" and look straight up through the gap. There is a 10mm screw, about one inch from the edge of the bumper/fender. This screw holds the bumper to the fender. Use a 10mm socket and a long extension to remove it. (do both sides)
Then you can firmly pull the side of the bumper sideways from the car.
There are 4 of those plastic pin/clips to removed under the hood, next to the headlight. Then you can remove the two 10mm screws under the hood, and the bumper can be lifted off.

Each of the headlight housings are held on by two 10mm screws and a 10mm nut. The is one electrical connector to unclip.

There are 3 covers on each housing. Each cover is held on by 3 8mm? screws. Your low beam is the top bulb.


25548514-wfi1xyowpghsdcre2c1nwnv2-3-1.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-3.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-6.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-10.jpg

25548514-wfi1xyowpghsdcre2c1nwnv2-3-15.jpg

Mar 10, 2015 | 2008 Cadillac CTS 2.6

1 Answer

Where is battery located on 2008 dodge avenger sxt 2.4 cly.


The battery is in the driver side front fender. Check your owners manual for details.

Sep 23, 2013 | 2008 Dodge Avenger

1 Answer

I have a 2004 dodge ram 1500 with the 4.7 I have replaced the passenger side head lamp but can not get enough access to get at the driver side. Please help before I go at the front fender with a cutting...


i have the same year but i have a diesel....they come out the same way on both sides on my truck 2 bolts behing the grill and one under the outside edge of the light housing, between the bumper cover and the light housing...10mm i believe

Feb 16, 2011 | 2004 Dodge Ram 1500

4 Answers

Can't locate the battery


my 1999 dodge intrepid is located in the front passanger side fender well

Sep 02, 2010 | 2009 Dodge Avenger

2 Answers

Where is the battery in a 2008 dodge avenger


It is in the drivers side fender well in front of the tire, it is mounted to the front frame rail. You have to remove the plastic fender lining to get to it.

Dec 13, 2009 | 2008 Dodge Avenger

1 Answer

Where is the horn located on a 2008 avenger?


There are 2 of them behind the front bumper cover, about 6 inches below the headlights, 1 per side.

Nov 04, 2009 | 2008 Dodge Avenger

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

3 Answers

Battery changing


Ok, trust me on this one, take the drivers side tire off and remove the forward inner fender panel. If you try it without removing the tire, it is just a royal pain.

Aug 25, 2008 | 2008 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...