Question about Cars & Trucks

1 Answer

Misfire on cylinder 1 ford taurus 2000

Has change coil ignition, spark plugs and wires.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You will have to change the cylinder piston; the ring around the piston is what causing this to misfire. As you can see, every time you remove that one spark plug, to look as liquid is been spill on it. The ring around the piston is damage and the cylinder is not burning the oil and gas as the spark plug send fire into the cylinder. contact your local mechanic for hands on help.

Posted on Feb 19, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

landsend
  • 1066 Answers

SOURCE: misfire in cylinder 1 2001 mercury sable

Next change swap the injector with another and see of the problem moves.  If it does it's a bad injector.  

Posted on Mar 26, 2009

  • 59 Answers

SOURCE: My 2005 Chevy Equinox LT

Have you done a compression check? I had the same problem on an S-10 Chevy pick up. Found that # 3 cylinder had low compression due to a burnt exhaust valve. No more problems after having valve job done on the engine.

Posted on Feb 16, 2011

jamaicanmech
  • 17 Answers

SOURCE: Cylinder #1 misfire on a Ford Taurus SHO

do a compression check. if you have a low compreeion reading below 80psi you need to do a head job. question is the iol milky on the dip stick?

Posted on Jan 08, 2009

motor1258
  • 6674 Answers

SOURCE: 2003 Ford Taurus spark plug diagram

Have a look here.

http://www.autozone.com/N,26200242/shopping/specsSelect.htm

Posted on Feb 02, 2009

Dirt Dobber
  • 253 Answers

SOURCE: i have a 2004 ford freestar 3.9 The engine light

Probable coil due to age. It is a coil pack unit. Runs about 70.00 from parts store and not hard to change. Another possibility is the fuel injector, it's connector or wiring to it from PCM. Have a mechanic do a compression test on the cylinder to eliminate a mechanical issue i.e. burned or bent valve or piston rings bad.
Good luck!

Posted on May 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When i turn on my 04 taurus. It starts makin knock sound , i replaced my lower intake n i think i missplaced the spark plug wiring


If the spark plug wiring is not correct, the engine will misfire and that will create erratic combustion, which is a shock to the cylinder, which results in a load harsh noise. Locate the number 1 spark plug wire on the distributor cap and trace each wire to the spark plugs. The firing order will be listed on the intake manifold. Make the correct wire to spark plugs attachments as needed.

Oct 11, 2016 | 2004 Ford Taurus

1 Answer

Po316 y po303 en Ford tAurud 2003


Cylinder # 3 has a misfire...#1) Defective coil on plug or the spark plug itself...#2) Contaminated fuel injector...See drawings below...The coil pack is the smaller of the two and sits to the rear of engine it is the most probable cause...Although the spark plug or the ignition wire (connection between plug and coil pack) could be at fault...so, before you invest in a new coil pack...Remove from both ends the wire from #3 and switch it with #2...if the fault code changes to p0302 that wire is bad...next Install a new set of plugs....Fault still present? replace the coil pack.....Unless recently changed new plugs and wires are a plus even if fault remains...saailer


25648931-vzzc52ao251lv4b5zemk330u-5-0.gif

25648931-vzzc52ao251lv4b5zemk330u-5-1.jpg
Cost= about $90

Apr 15, 2015 | 2003 Ford Taurus

3 Answers

My 1996 Taurus when I press the gas pedal when cold it sputters and lacks power. When it warms up it runs great.


Possible causes - Faulty spark plug 5
- Clogged or faulty fuel injector 5
- Faulty ignition coil 5
- Fuel injector 5 harness is open or shorted
- Fuel injector 5 circuit poor electrical connection
- Ignition coil 5 harness is open or shorted
- Ignition coil 5 circuit poor electrical connection
- Insufficient cylinder 5 compression
- Incorrect fuel pressure
- Intake air leak

The P0305 code means that the cylinder 5 is misfiring or is randomly misfiring. Start by checking for intake leaks an if no leaks are found the next step is to replace the spark plugs on cylinder 5. If the problem persist more tests needs to be done to diagnose problem, see "Possible Causes



When is the code detected? Engine Cylinder 5 is Misfiring.


When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, the Engine Control Module (ECM) can determine that a misfire is occurring.



Oct 21, 2014 | 1996 Ford Taurus

1 Answer

Code reader says my 2000 taurus is misfiring in no 6 cylinder i need to know what might be causing it


if it has a ignition coil over each cylinder very common for them to go out. easy change once you get to it only two bolts pops off new one pops on gl if thats your problem. if no coils over cylinders check your coil pack, faulty wire, faulty plug GL

Jan 04, 2013 | 2000 Ford Taurus

1 Answer

Misfire on cylinder 1 on ford taurus 2000


could be a bad fuel injector, bad pcm, or an internal engine issue

Feb 18, 2012 | 2000 Ford Taurus

1 Answer

There is a misfire in my engine, changed plugs & wires. now it reads that the fuel leveling sensor is bad, will this help?


If there is a misfire, the cylinder that it is misfiring in will be recorded as a code in the computer.

Have the car scanned to determine which cylinder is bad. Then, replace the coil pack going to that cylinder.

Ignition Coil Pack Removal & Installation 2V Engine To Remove:
  1. Twist the spark plug wires off of the ignition coil towers. Mark the spark plug wire positions so they can be installed in their original positions.
  2. Disconnect the electrical connector from the ignition coil. CAUTION
    When removing the spark plug wires, a slight twisting motion will break the seal and ease removal.
    coilconn.gif

  3. Remove the mounting screws and remove the ignition coil.
To Install:
  1. Position the ignition coil pack on engine.
  2. Install mounting screws and torque to 53 in-lbs. (6 Nm). coilbolt.gif

  3. Connect ignition coil pack electrical connector.
  4. Match previously marked spark plug wires to ignition coil and install.
4V Engine To Remove:
  1. Remove the RH cowl grille cowlpic.gif
  2. Remove the screws and the water shield
  3. Mark spark plug wire positions
  4. Disconnect the spark plug wires from the ignition coil CAUTION
    When removing the spark plug wires a slight twisting motion will break the seal and ease removal.
  5. Disconnect the ignition coil electrical connector coilconn.gif

  6. Remove the mounting screws and remove the ignition coil
To Install:
  1. Position ignition coil pack. Install mounting screws and torque to 56 in-lbs. (6Nm)
    coilbolt.gif

  2. Connect ignition coil pack electrical connector
  3. Match previously marked spark plug wires to ignition coil and install
  4. Position water shield and install screws
  5. Install RH cowl panel
prev.gif next.gif

Aug 11, 2010 | 2002 Ford Taurus

4 Answers

I have a 2000 Ford Taurus and it has been running rough for the last couple of months, but my obdII scanner reads nothing. Just this morning my check engine light came on so I put my scanner back on and it...


my taurus did not do this until i had over 124,000 miles you may have to replace all of the plugs and the wires and the fuel filter give this website a try www.taurusclub.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Dec 03, 2009 | 2000 Ford Taurus

1 Answer

2005 Ford Taurus Sputtering


stickingvalves collapsed lifters bent push rods fault ignition or damadged spark plug wires start it up at night look under the hood for sparks jumping from wires replace fauilty wires

Jun 22, 2009 | 2000 Ford Focus

2 Answers

Daewoo lanos 2000 car is misfiring and wont run properly firing on cylinders 1 and 4 misfiring


have you changed the ignition wires? perhaps firing order crossed? if not coil pack or ignition wires faulty how do you know it is not "FIREING" on 1 & 4 have you tested it with a spark tester tool???

Dec 23, 2008 | 2000 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...