Question about 2005 Jeep Grand Cherokee
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Jeep 1995 Grand Cherokee won't
You probably disconnected the battery to install the new fuel pump. The alarm system will act in this manner after reconnecting the battery. Put the key in the door and lock the door. Then unlock the door. Try starting the vehicle now.
Posted on Mar 11, 2009
Has any one soled this yet???????? Because I have the the same prob. but mine is only when it is could out blow 65 it will start but I have to keep my foot on the gas like a carb with no choke
Posted on Dec 27, 2009
SOURCE: 1996 jeep cherokee 4.0 MPI.
Lets start with technical bulletin how to determine whether fuel pressure regulator is at fault or not :-
FUEL PUMP PRESSURE TEST - ALL ENGINES WITH PRESSURE TEST PORT
Use this test in conjunction with the Fuel Pump Capacity Test, Fuel Pressure Leak Down Test and Fuel Pump Amperage Test found elsewhere in this group.
Check Valve Operation: The electric fuel pump outlet contains a one-way check valve to prevent fuel flow back into the tank and to maintain fuel supply line pressure (engine warm) when pump is not operational. It is also used to keep the fuel supply line full of gasoline when pump is not operational. After the vehicle has cooled down, fuel pressure may drop to 0 psi (cold fluid contracts), but liquid gasoline will remain in fuel supply line between the check valve and fuel injectors. Fuel pressure that has dropped to 0 psi on a cooled down vehicle (engine off) is a normal condition. When the electric fuel pump is activated, fuel pressure should immediately (1 - 2 seconds) rise to specification.
All fuel systems are equipped with a fuel tank module mounted, combination fuel filter/fuel pressure regulator. The fuel pressure regulator is not controlled by engine vacuum.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. BEFORE DISCONNECTING FUEL LINE AT FUEL RAIL, THIS PRESSURE MUST BE RELEASED. REFER TO THE FUEL SYSTEM PRESSURE RELEASE PROCEDURE.
1. Remove protective cap at fuel rail test port. Connect the 0 - 414 kPa (0-60 psi) fuel pressure gauge (from gauge set 5069) to test port pressure fitting on fuel rail
2. Start and warm engine and note pressure gauge reading. Fuel pressure should be 339 kPa ± 34 kPa (49.2 psi ± 5 psi) at idle.
3. If engine runs, but pressure is below 44.2 psi, check for a kinked fuel supply line somewhere between fuel rail and fuel pump module. If line is not kinked, but specifications for either the Fuel Pump Capacity, Fuel Pump Amperage or Fuel Pressure Leak Down Tests were not met, replace fuel pump module assembly.
4. If operating pressure is above 54.2 psi, electric fuel pump is OK, but fuel pressure regulator is defective. Replace fuel filter/fuel pressure regulator. .
5. Install protective cap to fuel rail test port.
The fuel pressure regulator is part of the fuel pump, it is in the fuel tank.
On this vehicle the regulator is part of the pump and not serviceable separately so if the regulator is bad the whole pump assembly will need to be replaced.
Posted on Aug 19, 2010
Tips for a great answer:
Oct 27, 2014 | 2011 Jeep Grand Cherokee
Feb 15, 2011 | 1995 Jeep Grand Cherokee
Jan 06, 2011 | 1998 Jeep Grand Cherokee
Jul 28, 2010 | 2002 Jeep Grand Cherokee
Jun 04, 2010 | 2004 Jeep Grand Cherokee
Jun 01, 2010 | 2000 Jeep Grand Cherokee
Aug 15, 2009 | 1995 Jeep Grand Cherokee
Jul 01, 2009 | 2000 Jeep Grand Cherokee
Jun 28, 2009 | 1997 Jeep Grand Cherokee
119 people viewed this question
Usually answered in minutes!