Question about Ford Contour

1 Answer

How do i replace the ECM on a 1999 ford contour with a 2.0L engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 500 Answers

The PCM is behind the passengers kick panel, but i recomend taking it to a ford dealer to have it installed, because it needs to be programed with a ford diagnostic computer.

Posted on Feb 19, 2012

Testimonial: "Thanks,easier than i thought it would be"

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: how to time up a 1999 ford contour

how to change a timing belt

Posted on Jul 06, 2008

emissionwiz
  • 76109 Answers

SOURCE: 1999 ford contour fuel pump removal

YOU will need the car on a hoist, doing it on the ground is almost impossiable, disconnect the filler neck at top, remove the straps, lower tank slow and disconnect wiring and fuel hoses, you need a special tool to remove the gas line retainer clips.

Posted on Jul 28, 2008

  • 1596 Answers

SOURCE: drivers door glass replacement 1999 ford contour

REMOVAL


Remove the door trim panel.

Detach the door speaker.
Remove the speaker retaining screws.



Remove the door speaker.
Disconnect the multiplug.




Detach the watershield.
Using a plastic knife (disposable cutlery), cut through the Butyl strip to enable the watershield to be peeled back.
CAUTION: Do not touch the adhesive surface as re-bonding will be impaired.


Connect the window operating switch electrical connector.




Remove the window retaining bolts. NOTE: Align the window retaining bolts with the access holes.
Disconnect the battery ground cable.



Remove the door interior weatherstrip (power window shown


Remove the glass.
Lift the glass.
Tip the glass forwards and remove the glass.
INSTALLATION

To install, reverse the removal procedure

Posted on Jan 23, 2009

  • 5 Answers

SOURCE: WIRING DIAGRAM A/C SYSTEM ON A 1999 FORD CONTOUR,2.0L ENGINE

Haynes Manuals not Chiltons are the source I use for wiring. You local library might have one and photocopy it off.

Posted on Sep 16, 2009

SOURCE: how to replace spark plugs for 1999 ford contour

to replace spark plugs remove spark plug wire boots. use special sparkplug socket or else you can break the sparkplug. to remove turn ratchet counterclockwise remove all four one at a time, make sure that the sparkplug gap is correct. most plugs come pregapped...read the box it will tell.you. do not overtigheten plug once it has fully seated give it a good snug....if you do one at a time you dont need to mark the spark plug wires. if you mix up the wires your car will back fire which could cause severe internal damage.

Posted on Feb 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Ford Contour goes dead and will not start till engine cools, What causes this problem?


This could be either the crankshaft sensor or the temp sensor on the engine. IF you have a check engine light that is on, you can get the codes from it and see.

Oct 10, 2014 | 1999 Ford Contour

1 Answer

Can someone please tell me where to hook up a timing lite on my 1999 ford contour


The timing on Contours is not adjustable, as it is controlled by the Engine Control Module (ECM), the computer that controls and monitors the engine functions.

Aug 06, 2013 | Ford Contour Cars & Trucks

1 Answer

1999 ford contour se custom sport check engine light stays on recently had new alternator replaced and when i turn heat on it only runs on hi otherwise car is running ok will the check engine light go off...


Contour's are notorious for check engine lights. Mine has been on for years. The only way really to reset the CEL is to rent or buy a code reader and record the codes that are stored. Information on CEL codes is available on the internet. FYI the most common code for contour's are P0420 and P0421. These won't cause any driveability issues. As for your heater problem, your fan blower relay is toast

Feb 13, 2010 | 1999 Ford Contour

1 Answer

I have a 1999 Contour, it died while driving. Has power, no start


Most the time the engine dies while driving is due to a crankshaft sensor failure. When this fails, the engine can't be started since the ECM doesn't know the location of TDC to provide proper ignitions. Have a shop check out and replace this part then you are good to be back on the road. Good luck.

Dec 13, 2009 | 1999 Ford Contour

1 Answer

I need to get the timing on my 1999 Contour correct. I had to replace a tension pulley and now the timing is off.


what kind of engine 2.0 or 2.5 24 valves? o check the 8th vin if you wanna now the rigth engine type

Oct 20, 2009 | 1999 Ford Contour

1 Answer

WIRING DIAGRAM A/C SYSTEM ON A 1999 FORD CONTOUR,2.0L ENGINE


Haynes Manuals not Chiltons are the source I use for wiring. You local library might have one and photocopy it off.

Sep 11, 2009 | 1999 Ford Contour

1 Answer

PVC valve location


#10 is the PCV valve.
b8fe447.gif

May 05, 2009 | 1999 Ford Contour

1 Answer

Rough idle


check to see if your map sensor is plugged in

Apr 27, 2009 | 1999 Ford Contour

1 Answer

Replacing timing belt on a 1999 ford contour 2.0


moz-screenshot-6.jpgCAUTION The 2.0L engine is an interference motor. Extending thereplacement interval could lead to the belt breaking and severe andcostly engine damage. Care must be taken if rotating the crankshaft orcamshafts with the belt off, if resistance is felt, do not force themto turn.

0900c152800a89b9.jpg

0900c152800a89bb.jpg

Apr 10, 2009 | 1999 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...