Question about Holden Commodore

Open Question

Need a diagram for the cam timing marks for a 253 - 308 holden

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: torque settings for holden 308

see if this site helps you.

http://www.boxwrench.net/specs_index.htm

Posted on Nov 13, 2008

Ad
  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

stevenhurc
  • 450 Answers

SOURCE: wheres the timing marks on the crank

cam gear mark lines up with head at 9 o clock and dowl pin near centre bolt is at 12 o clock
crank gear keyway at 12 o clock and mark in disc behind gear lines up with mark on oil pump at 12 o clock also.

Posted on Jun 25, 2009

  • 101 Answers

SOURCE: need diagram of cam marks and crankshasft marks for timing belt set up

they are on the t/belt cover.

Posted on Aug 05, 2009

  • 279 Answers

SOURCE: timing marks on peugeot 1.9 tdi

there is a few ways of doing thes the easiest way being using locking pins
you bont have to go and buy a set of locking pins you can use 3 m8 (13mm headded) bolts and a 5mm allen key

there is a hole in the cam pully and 2 holes in the injection pump pully and 1 in the fly wheel

i suggest you lock the fly wheel up first
the hole is located under the starter motor on the front of the block
insert the 5mm allen key and get someone to turn the crank pully clockwise until allen key engages into the fly wheel

the hole in the cam should be at about 25 past
(if it is at 10 to then you neet to remove the pin from the fly wheel and turn the crank 1 full turn)

when the hole is inthe right place you can insert a m8 bolt and wind it in to the head

with this now lined up you should be able to fit the other 2 m8 bolts into the injector pump pully

with this now done your 1.9 tdi engine is timed up

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I don't no we're the timing marks are on 2006 Holden viva I got it at TDC but don't on the marks on top two pulleys


Hi Michael Timing marks are on the cam pulleys (Dots or grooves), you should use a cam locking tool as it is important to lock them in place.The left gear mark should be at 3 O'clock & right at 9 O'clock (radiator side) the two marks should be exactly in line. If you put a steal ruler across the center of the cam bolts the two marks on pulleys should be level with ruler.The crankshaft has a dot on the face of the sprocket or a triangular shape this should align with a mark on the bottom of the plastic rear timing cover.It should be slightly raised and easy to see. If it has an alloy base to the cover there will be a slot cut in it the dot or triangular shape should align with this. All three marks need to be in possition at the same time when installing the timing belt. There should also be an arrow on the tentioner for direction of tightning the belt. Good luck

Feb 25, 2017 | Holden Cars & Trucks

1 Answer

I m looking for chain timing marks on xc 1.4 holden combo any one can help please


there is no marks on both camshaft gears or chain, and special tools are required if this is the twin cam engine with chain drive not belt.
timing mark on crank pulley must line up with mark on cover then there is a special tool that lock both camshafts at rear in the flat slots as well as lock pin to put into hole in block that locks cranck shaft.
then there is another special tool for camshaft sensor interuptor ring which is on one of the camshaft gears.

Mar 08, 2014 | Holden Barina Cars & Trucks

1 Answer

Diagram timing chain rodeo holden 2007


please oost to holden , not jeeps.
and answer can get 100x better , and location, helps too.
country.

Jan 27, 2014 | Jeep Commander Cars & Trucks

1 Answer

Do you know the marks for cambelt in a holden astra 2001. We thought we had it but now the whine won't fire up! Any suggestions??


hey mate.when you look at the cam gears you will see the timing marks like 2 lines carved in the gear.when setting the timing these 2 marks need to line up and look at each other.the intake cam mark should be at 3oclock and the exhaust at 9oclock.
use cam lock.

Sep 14, 2013 | Cars & Trucks

1 Answer

Timing belt diagrams 2003 holden 'vectra 3.2ltr


We do not have these diagrams, suggest you buy a service manual, try eBay for a used one.

Apr 30, 2012 | Holden Vectra Cars & Trucks

2 Answers

I need timing marks diagram for a 2002 hyundai accent gl


Hello tazzie13101,

Below is an image showing the timing marks. I circled the detail for the hole in the cam sprocket, you will look through the hole to aline the mark for the cam.

netvan_243.png

I hope this helps.

Regards,

Jerry

Sep 14, 2011 | Hyundai Accent Cars & Trucks

2 Answers

Replace timing belt Holden vectra 2.2ltre.i need to know how to set up the marks


timing cover has marks on it,line it up with pulley,remove pulley and cover,check to see if any marks on camshaft.un do tensioner.to be sure make your own marks

Jan 01, 2010 | 1999 Isuzu Rodeo

1 Answer

Wheres the timing marks on the crank and cam for a holden gemini rb 1985


cam gear mark lines up with head at 9 o clock and dowl pin near centre bolt is at 12 o clock
crank gear keyway at 12 o clock and mark in disc behind gear lines up with mark on oil pump at 12 o clock also.

Jun 10, 2009 | 1990 Isuzu Amigo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

643 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...