Question about 2005 Chevrolet Aveo Sedan

Open Question

Torque specs for 2005 aveo engine - 2005 Chevrolet Aveo Sedan

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

johnny5846
  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

  • 1 Answer

SOURCE: torque specs for the cylinder head

2004 ENGINE
Engine Mechanical - 1.6L (L91) - Aveo
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fastener Tightening Specifications
Application
Specification
Metric English
A/C Compressor Mounting Bolts 27 N.m 20 lb ft
A/C Compressor Mounting Bracket Bolts 50 N.m 37 lb ft
Air Filter Housing Bolts 12 N.m 106 lb in
Alternator Adjusting Bolt 20 N.m 15 lb ft
Alternator Adjusting Bracket Retaining Bolt 20 N.m 15 lb ft
Auxiliary Catalytic Converter-to-Exhaust Manifold
Nuts and Bracket Bolts
40 N.m 30 lb ft
Camshaft Cap Bolts 16 N.m 12 lb ft
Camshaft Gear Bolt 67.5 N.m 49 lb ft
Camshaft Pressure Plate Bolts 10 N.m 89 lb in
Connecting Rod Bearing Cap Bolts 25 N.m+30°+15° 18 lb ft+30°+15°
Coolant Pump Retaining Bolts 10 N.m 89 lb in
Coolant Temperature Sensor 20 N.m 15 lb ft
Crankshaft Bearing Cap Bolts 50 N.m+45°+15° 37 lb ft+45°+15°
Crankshaft Position Sensor Retaining Bolt 10 N.m 89 lb in
Crankshaft Pulley Bolt 95 N.m+30°+15° 70 lb ft+30°+15°
Cylinder Head Bolts - Camshaft Support Housing
and Cylinder Head Mounting Bolts
25 N.m+60°+60°
+60°+15°
18 lb ft+60°+60°
+60°+10°
Electronic Ignition System Ignition Coil Mounting
Bolts
10 N.m 89 lb in
Electronic Ignition System Ignition Coil Mounting
Plate Bolts 10 N.m 89 lb in
Engine Mount Bracket Retaining Bolt 65 N.m 48 lb ft
Engine Mount Bracket-to-Engine Mount Retaining
Bolts
60 N.m 44 lb ft
Engine Mount Retaining Nuts 40 N.m 30 lb ft
Exhaust Flexible Pipe Bracket Bolts 40 N.m 30 lb ft
Exhaust Gas Recirculation Valve Adapter Bolts 25 N.m 18 lb ft
Exhaust Manifold Heat Shield Bolts 15 N.m 11 lb ft
Exhaust Manifold Nuts 25 N.m 18 lb ft
Flexible Plate Bolts 60 N.m 44 lb ft
Flexible Plate Inspection Cover Bolts 10 N.m 89 lb in
Flywheel Bolts 35 N.m+30°+15° 26 lb ft+30°+15°
Flywheel Inspection Cover Bolts 12 N.m 106 lb in
Front Muffler-to-Main Catalytic Converter Nuts 30 N.m 22 lb ft
Fuel Rail Retaining Bolts 25 N.m 18 lb ft
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 1 of 330
http://www.eautorepair.net/app/PrintItems.asp?S0=2097152&S1=0&SG=%7BEEDCF... 3/30/2009
ENGINE MECHANICAL SPECIFICATIONS
Engine Mechanical Specifications
Intake Manifold Retaining Nuts 25 N.m 18 lb ft
Intake Manifold Support Bracket Lower Bolt-to-
Engine Block 40 N.m 30 lb ft
Intake Manifold Support Bracket Upper Bolts 25 N.m 18 lb ft
Lower Timing Belt Cover Bolts 10 N.m 89 lb in
Oil Pan Retaining Bolts 10 N.m 89 lb in
Oil Pressure Switch 40 N.m 30 lb ft
Oil Pump Retaining Bolts 10 N.m 89 lb in
Oil Pump/Pickup Tube and Support Bracket Bolts 10 N.m 89 lb in
Oil Pump Safety Relief Valve Bolt 36 N.m 22 lb ft
Oil Pump Rear Cover Bolts 6 N.m 53 lb in
Power Steering Pump Mounting Bolts 25 N.m 18 lb ft
Power Steering Pump Pulley Bolts 25 N.m 18 lb ft
Rear Timing Belt Cover Bolts 10 N.m 89 lb in
Spark Plug Cover Bolts 3 N.m 27 lb in
Spark Plugs 25 N.m 18 lb ft
Thermostat Housing Mounting Bolts 20 N.m 15 lb ft
Throttle Cable Bracket Bolts 8 N.m 71 lb in
Timing Belt Automatic Tensioner Bolt 25 N.m 18 lb ft
Timing Belt Idler Pulley Bolt 40 N.m 30 lb in
Transaxle Bell Housing Bolts 75 N.m 55 lb ft
Transaxle Brace Bolts 40 N.m 30 lb ft
Transaxle Torque Converter Bolts 65 N.m 48 lb ft
Upper Timing Belt Cover Bolts 10 N.m 89 lb in
Valve Cover Bolts 10 N.m 89 lb in
Application
Specification
Metric English
General Data
 Engine Type 4 Cylinder - In-Line
 Displacement 1598 cm3 97.51 in3
 Bore Stroke 79.0x81.5 mm 3.1x3.21 in
 Compression Ratio 9.5:1
 Firing Order 1-3-4-2
 Maximum Power - At 6200 RPM 77 kw/103.3 hp
 Maximum Torque - At 3400 RPM 145 N.m 106.9 lb ft
Cylinder Bore
 Diameter 79 mm 3.1 in
 Out of Round - Maximum 0.0065 mm 0.00025 in
 Taper - Maximum 0.0065 mm 0.00025 in
Piston
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 2 of 330

Posted on May 09, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

  • 32 Answers

SOURCE: i need the head bolt torque specification for a

install:

  1. The cylinder head should be cleaned and inspected prior to installation.
  2. Lightly oil all bolt and stud bolt threads before installation.
  3. Clean all gasket mating surfaces thoroughly.
  4. Install a new head gasket on the cylinder block. WARNING Always use new cylinder head bolts when installing the cylinder head or damage to the engine may occur.
  5. Install the cylinder head on the cylinder block.
  6. Tighten the cylinder head bolts in reverse of the removal sequence. Tighten the 2004 cylinder head bolts to 18 ft. lbs. (25 Nm). Tighten an additional 70°, plus 70°, plus another 50°. Tighten 2005 bolts to 18 ft. lbs. (25 Nm). Tighten an additional 60°, plus 60°, plus another 10°.
  7. Install the right engine mount. Tighten the engine mount attaching bolts to 22 ft. lbs. (30 Nm).
  8. Install or connect the following:
    • Intake manifold
    • Intake manifold support bracket. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Throttle cable
    • Surge tank coolant hose
    • Heater hose to cylinder head
    • Fuel feed line at the fuel rail
    • All vacuum hoses
    • Exhaust manifold
    • Rear timing belt cover
    • Timing belt tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Idler pulley. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Intake and exhaust camshaft gears. Tighten the bolts to 49 ft. lbs. (68 Nm).
  9. Apply a small amount of gasket sealant to the corners of the front camshaft caps and the top of the rear camshaft cover-to-cylinder head seal.
  10. Install the valve cover using a new gasket
  11. Align the timing marks on the camshaft gears.
  12. Align the mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.
  13. Install the timing belt and rotate the water pump clockwise to apply tension to the timing belt.
  14. Tighten the water pump bolts to 89 inch lbs. (10 Nm).
  15. Adjust the timing belt tension.
  16. Install or connect the following:
    • Spark plug wires
    • Upper and lower timing belt coversCrankshaft pulley. Tighten the bolt to 70 ft. lbs. (95 Nm), plus an additional 30°, then another 15°.
    • Accessory drive belt
    • Air cleaner housing
    • Radiator hoses
    • Front splash shield
    • Right front wheel
    • Coolant temperature sensor
    • Fuel feed line from fuel rail
    • IAT sensor
    • Intake manifold pressure sensor
    • DIS coil connector
    • Fuel injector connectors
    • ECM ground terminal
    • Negative battery cable
  17. Fill the engine with oil and coolant.
  18. Start the engine and check for leak0900c1528009e8b5.jpg

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lower intake torque spec for 2005 cyrysler pacifica


1st stage 9 ftlbs
2nd stage 21 ft lbs
Note the torque sequence. This info is for 3.8L engine. The torque specs came from autodata tune-up cd, it has a lot of torque specs for different makes--models--years. If somebody has info from a better database, please jump in. All databases are not created equal.
lower-intake-torque-spec-2005-cyrysler-0oecaoes3ykpgpibvdkntfh2-4-0.jpg

Nov 06, 2016 | Cars & Trucks

1 Answer

Front brake torque specs 2010 chevy aveo lt


Just tighten hard as you can,I have never torque my brake parts.

Jun 29, 2015 | Cars & Trucks

1 Answer

Head torque specs for 2005 chevy aveo


The torque spec is 18 ft-pound for the cylinder head

Mar 13, 2011 | Chevrolet Aveo Cars & Trucks

1 Answer

2004 chevy aveo head torque espesc


you can get the torque specs from the dealer. if you replaced the valve cove gasket the just tighten the about the same as you would yor tire by hand not with a power tool!

Aug 04, 2010 | 2004 Chevrolet Aveo

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

What torque spec for chev aveo 2004 cylinder head


18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Jul 04, 2009 | 2004 Chevrolet Aveo

1 Answer

2004 CHEVY AVEO THROWING CODES P0700 TRANSMISSION CONTROL SYSTEM,P0300 RANDOM MISFIRE DETECTED, P1781 ENGINE TORQUE SIGNAL CIRCUIT. CAR RANDOMLY DIES DRIVING ON THE HIWAY, PULL OVER,STOP RESTART CAR GOES...


there is a Technical service bulletin for this problem, the number of the TSB is 01575, TSB Date:January 1, 2004
It has to do with engine valve seating problems.

Jun 03, 2009 | 2005 Chevrolet Aveo

1 Answer

I need torque specs for a 2004 chevy aveo front hub. installing new rotors


torque specs. to a 2001 chevrolet malibu 3.1 engine with also needing head and manifold torque specs. as well.

Jul 18, 2008 | Chevrolet Aveo Cars & Trucks

Not finding what you are looking for?
2005 Chevrolet Aveo Sedan Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...