Question about Cars & Trucks

Open Question

VALVE COVER TORQUE SPECS 09 SANTA FE - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: bolt torque specs

I have used Haynes service manuals for (hate to admit it) many decades and I recommend you check to see if this one:

http://www.amazon.com/Haynes-Toyota-Automotive-Repair-Manual/dp/1563923513

doesn't cover your engine.

I have found darned few 'holes' in their coverage.

Auto parts stores carry these and I suspect that even though sealed, the sales people will not give you too hard of a time if you explain you want to insure you are getting what you need.

Haynes is not the same as it was 20 years ago before they were acquired by Chilton but the price/utility ratio is still pretty good.
Mostly I'm annoyed by the move to cheaper paper (newsprint)that is fussier, picks up dirt, tears more easily than the better paper of yore.

Posted on Aug 20, 2008

  • 1 Answer

SOURCE: vale cover torque specs

They are 84 inch-lbs. I just got done replacing the gasket on a 92 also.

Posted on Apr 30, 2009

ourhowse
  • 2007 Answers

SOURCE: torque specs for valve cover

not sure there is such a thing. I've never seen anybody use a torque wrench on valve cover bolts. Just use a nut driver (screwdriver type) or a 1/4 inch drive ratchet, and tighten as much as you can. They don't need to be very tight.

Posted on May 04, 2009

alicantecoli
  • 22095 Answers

SOURCE: torque specs

about 7lbs for the rocker cover

Posted on Jun 21, 2009

abauto
  • 353 Answers

SOURCE: i need the torque specs for a 2000 honda accord 4

7.2 ft lbs

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 Bmw x5 valve cover torque specs


valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...
Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

Nov 06, 2015 | Cars & Trucks

1 Answer

Torque specs on 2004 Hyundai a Santa Fe 3.5 GLS differential cover plate bolts


1 MIN IS CUTTING IT CLOSE BUT YOU SHOULD BE ABLE TO MAKE IT. TORQUE SPECS SHOULD BE 14 TO 15 FOOT LBS.

Aug 18, 2014 | 2004 Hyundai Santa Fe

1 Answer

What is torque specs on hyundai Santa Fe 3.5 differential cover plate bolts


Suggest to remove cover and replace gasket with Permatex Gasket Maker Silicone. Fully clean and dry apply a 1/4 bead on cover and bolt down to 20 ft lbs. go around several times to compress silicone. Let silicone cure 30 minutes then refill.

Aug 18, 2014 | Cars & Trucks

1 Answer

Oil leaking from rear valve cover gasket & getting burnt oil smell thru air vents inside vehicle


Thi depends on whether you want to do it yourself or not. It's an easy fix, just get the gasket and remove the valve cover. It's tidious but doable. Otherwise, get ready to spend $150-200 for a shop.

Mar 07, 2014 | 2003 Hyundai Santa Fe

1 Answer

How to replace a valve cover gasket 2003 hyundai santa fe


Just take a picture of it with digital camera or phone. And start removing wires and hoses until they are all out of way of cover. Then remove the bolts all way around cover and pull straight up and it will come right off. If not use a flat head screw driver to prise it off. Clean old gasket off of valvecover and engine. then put it bak together. Tighten bolts slowly, start with ones in center ov it and work your way out. Just finger tight. Then snug, then torque em down. Not too tight as if tostrip the bolt or break it off. Cause it be very expensive. also write down everywhere each wire go's unless you can remember

May 11, 2010 | 2003 Hyundai Santa Fe

1 Answer

What are the torque wheel settings for cars and suv's?


If you mean the torque spec for the wheel nuts and bolts its in your owners manual

Apr 26, 2010 | 2001 Hyundai Santa Fe

2 Answers

2.4l santa fe spark plug location


there are 2 covers that are over the plugs the first is the big silver and black cover that has four
10mm bolts remove them and then there is a small black cover that is inbetween the two humps on the valve cover i think that there 6 bolts that holdthat down remove this and the coils and plug wires are visable

Apr 12, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...