Question about 2004 Mercury Sable

Open Question

Where is map sensor on 2004 mercury sable - 2004 Mercury Sable

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: Oxygen Sensors

ok Bank 1 is the rear bank and bank 2 is the front bank sensor 1 in each bank is the one closest to the manifold they have green connectors sensor 2 is the sensor after the cat converter and is a blue connector

Posted on Dec 02, 2008

warlock61
  • 659 Answers

SOURCE: location of the camshaft position sensor in a 2004 mercury sable

it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

Posted on May 03, 2009

  • 1 Answer

SOURCE: I drive a 2004 mercury sable, what is the symptoms

Thanks for checking on me. I found the answer to my question to confirm the car symtoms.

Posted on Dec 13, 2009

alicantecoli
  • 22114 Answers

SOURCE: on a 2000 mercury sable where is the oxygen sensor

sensor 2 is normally the one after the cat but which side i wouldnt know for this model ,try testing them with a volt meter for the heater as this is what goes first ,the heater uses the two wires the same colour

Posted on Nov 23, 2010

SOURCE: 2004 mercury grand marque check

PO 108 --- Baro/Map Sensor High Voltage Detected

Yes it does

It is integrated into one unit in the ESM EGR assembly
(possibly)

I have no experience with that,so if you find only an egr valve
& no other sensor with vacuum hoses & wires going to it,replace
the egr valve.

Getting the feeling you missed it

Work the web sites. Put in your motor & EMS Module for egr
& see what comes up

Posted on Sep 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Mercury sable MAF and MAP sensors


2005 Mercury sable MAF and MAP sensors ?????? What about them ?

Apr 05, 2017 | 2005 Mercury Sable

1 Answer

Location of a MAP sensor on a 2000 mercury sable


The MAF sensor is bolted to the air box. it has the multi wire connector attached to it.

Sep 16, 2015 | Mercury Cars & Trucks

2 Answers

I have a 2005 mercury sable the. check engine light came on. I took it to AutoZone and the readings said it's running lean. Wht does that mean and what could be the cause?


It means that the engine is running lean which can cause engine knock. When the knock sensors detect excessive knock they set the check engine light.
Low fuel pressure.
Dirty fuel filter.
Dirty or bad MAF sensor.
Bad MAP sensor.
Vacuum leak.

Bad injector.

Jun 07, 2015 | 2005 Mercury Sable

1 Answer

How to replace the upper hose 2004 mecury sable?


Loosen clamp or USe large pliers to open clamp depending on style..and pull off hose by wiggling it and slightly pulling

Sep 02, 2014 | 2004 Mercury Sable

1 Answer

99 sable won't start, replaced battery,starter,alternator, but still wont even crank. code reader also said map sensor so it was reset worked for alittle but now nothing


If the car does not have a security system, I would check for voltage at the starter from the battery and from the key switch.
The power from the key switch goes thru the neutral safety switch before getting to the starter.

Sep 06, 2012 | 1999 Mercury Sable

3 Answers

Need serpentine belt diagram 4 merc sable 3.0


...are under hood, a diagram on top of radiator support.

Feb 12, 2010 | 2004 Mercury Sable

1 Answer

I drive a 2004 mercury sable, what is the symptoms of a car having problem with the cam sensor and synchronize.


Thanks for checking on me. I found the answer to my question to confirm the car symtoms.

Dec 12, 2009 | 2004 Mercury Sable

1 Answer

Location of the camshaft position sensor in a 2004 mercury sable


it is located on top of the engine right below the air inlet tube at the base of the intake it is a black sensor on top of a silver housing where the distributor would normally be

May 01, 2009 | Mercury Sable Cars & Trucks

Not finding what you are looking for?
2004 Mercury Sable Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...