Question about Ford F-350 Super Duty

Open Question

I have a 2010 ford f350 superduty its reading p0528 p0480 p2263 p1000 please help

Its got an EGR and DPF delete on it

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 208 Answers

SOURCE: 2000 ford explorer 4.0 x-engine is stalling, missing and lose power while driving

I personally would check the fuel pressure. Then I would go back to the coil. I have seen brand new bad coils out of the box. The symptoms of a loss of power point to this component, especially if the car idles well, but loses power when accelerating. Please do not rate this reply - we all are left to grasp at straws since you have changed pretty much everything. Good Luck. Please post the final fix of the problem.

Posted on Oct 28, 2008

emissionwiz
  • 75066 Answers

SOURCE: does the 2006 ford f350 superduty truck have a

no there is no "AUX" jack on any Ford radio in this year, there is however a connector port on some for a Ford auxiliary amplifier.

Posted on May 06, 2009

  • 166 Answers

SOURCE: 99 f350 fuse for the speedemeter

there is no speedo fuse . if it was a fuse the whole cluster would not be working . i think speed sensor with is on the trans . you should have a shop check this befor you start replacing parts

Posted on Jun 10, 2009

abauto
  • 353 Answers

SOURCE: how do you change glow plugs in 06 f350

Glow Plug: Service and Repair
Glow Plug
GLOW PLUG
Special Tool(s)

6c247a7.jpg Removal
1. CAUTION: Do not pull on the wiring to remove the glow plug connector or damage may occur.
NOTE:
Only one glow plug connector shown.
Using the special tool, remove the glow plug harness.
2. NOTE: If coolant residue is found on the glow plug, a new glow plug sleeve may have to be installed.
Remove the glow plug.
Installation
1. Install the glow plug.
- Tighten to 19 Nm (14 lb-ft).
2. Clean and apply clean engine oil to the O-ring seals.
3. Using the special tool, install the glow plug harness.



99c7f9c.jpg

There is a speed sensor on each front hub and one on top of the differential.

Posted on Sep 22, 2009

  • 8 Answers

SOURCE: Need a pic veiw of 2004 ford f350 6.0L diesel EGR

1st of all when Ford started out with putting "EGR's" on those diesel engines, they rushed it and are nothing less than a pain in the ***! i recommend having an EGR cleaning service performed by your local Ford dealer, i know they charge up the wazoo, but they're the best people to perform the service period.this is a VERY common problem with those engines and that service is "supposed" to be performed every 30K I believe. i dont recommend attempting to remove and service it youself, this WILL only make it worse.

Posted on Mar 26, 2010

Testimonial: "Im relieved to here that someone else is thinking the same thing. Im still going to try it myself as i am somewhat skilled at this but Thanks a bunch!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford expedition check engine light is on. It is reading a p405 code which is the egr sensor. I have change the sensor and the pig or electrical code twice . I brought the sensor from ford.


This DTC says nothing about changing the sensor or the connector or pig tail ! It's a circuit voltage low code
P0405 - DPF EGR Sensor Circuit Low Voltage Detected See DTC P1400 Problem with wiring or PCM !
P1400 - DPF EGR Sensor Circuit Low Voltage Detected The EGR monitor checks the DPF EGR sensor signal to the PCM for low voltage. The test fails when the average voltage to the PCM drops to a voltage less than the minimum calibrated value.
  • DPFEGR circuit short to GND
  • Damaged DPF EGR sensor
  • VREF short to GND
  • Damaged PCM
A DPF EGR PID reading less than 0.2 volt with the key ON and engine OFF or running, indicates a hard fault.

Sep 01, 2016 | 2003 Ford Expedition

1 Answer

What is mirror wiring for plugins?


Installing 08 mirrors on 01 Superduty, looking for wiring diagrams ...

www.ford-trucks.com > ... > Super Duty & Heavy Duty
Aug 12, 2008 - Installing 08 mirrors on 01 Superduty, looking for wiring diagrams Super Duty ... 2013-2014 mirror plug pin outs, SUPERDUTY_08, Super Duty ... Power/Heated/Lighted Tow Mirror upgrade...
Jul 24, 2012
F250 Paddle to towing mirror installation
Dec 20, 2010
Towing Mirror Wiring Harness Adaptor
Sep 15, 2010
Towing mirrors
Apr 16, 2010
More results from www.ford-trucks.com

Nov 19, 2015 | 2000 Ford F350 Super Duty Super Cab

2 Answers

Ford focus 2.0l tdci titanium 55 plate...the car is under boosting,


make and model would sure help someone help you

Apr 17, 2015 | Cars & Trucks

2 Answers

I have p 1121 and a P 0401 codes on my 1998 ford windstar. are these related? what can I check? replaced the mass airflow sensor recently.




P1121 Ford Throttle Position Sensor Inconsistent with Mass Air Flow Sensor
http://engine-codes.com/p0401_ford.html no they are not related !
Are there any cracks in the rubber hose from air cleaner to throttle body ! That could cause the P1121 air entering after mass air flow sensor !
P1121 - Throttle Position (TP) Sensor Inconsistent with MAF Sensor The PCM monitors a vehicle operation rationality check by comparing sensed throttle position to mass air flow readings. If during key ON engine running self-test the comparison of the TP sensor and MAF sensor readings are not consistent with calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.
  • Air leak between MAF sensor and throttle body
  • TP sensor not seated properly
  • Damaged TP sensor
  • Damaged MAF sensor
Drive vehicle and exercise throttle and TP sensor in all gears. A TP PID (TP V PID) less than 4.82 % (0.24 volt) with a LOAD PID greater than 55% or a TP V PID greater than 49.05% (2.44 volts) with a LOAD PID less than 30% indicates a hard fault. P0401 - EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
  • Vacuum supply
  • EGR valve stuck closed
  • EGR valve leaks vacuum
  • EGR flow path restricted
  • EGRVR circuit shorted to PWR
  • VREF open to D.P.F. EGR sensor
  • D.P.F. EGR sensor downstream hose off or plugged
  • EGRVR circuit open to PCM
  • VPWR open to EGRVR solenoid
  • D.P.F. EGR sensor hoses both off
  • D.P.F. EGR sensor hoses reversed
  • Damaged EGR orifice tube
  • Damaged EGRVR solenoid
  • Damaged PCM
Perform KOER self-test and look for DTC P1408 as an indication of a hard fault. If P1408 is not present, look for contamination, restrictions, leaks, and intermittents

Mar 09, 2015 | 1998 Ford Windstar

1 Answer

Hi my name is phil


- Faulty Injection Control Pressure (ICP) sensor
- Injection Control Pressure (ICP) sensor harness is open or shorted
- Injection Control Pressure (ICP) sensor circuit poor electrical connection
- EGR system fault

Aug 19, 2014 | 2003 Ford Focus

2 Answers

I have a scan tool that says my egr valve system not ready on my Ford f150 5.4 and my catylist reads not ready how can I fix this problem


ABout EGR codes, there are alot choive to look or diagnostic... are you chec or replace the vacuum lines as well? If there is a leak, the DPFE will read incorrectly.

Did you reset the PCM or disconnect the battery after the repair? Assuming all fuses are good, the P1401 indicates a possible wiring fault. Check the connector. Is it clean? Is it pushed in all the way? Are the wires in good condition?

Since the DPFE has been replaced, likely there is a restriction in the EGR line some where. This could also be a bad EGR valve. But first ensure that the EGR valve vacuum line is attached and leak free.

If no problem found, then the EGR passageways in the throttle body should be cleaned. Carbon will build up and block the EGR flow.

If still no problem found, consider replacing the EGR valve.

Keep in mind this information from Ford Service CD...

P0401 - EGR Flow Insufficient Detected
The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
Vacuum supply
EGR valve stuck closed
EGR valve leaks vacuum
EGR flow path restricted
EGRVR circuit shorted to PWR
VREF open to D.P.F. EGR sensor
D.P.F. EGR sensor downstream hose off or plugged
EGRVR circuit open to PCM
VPWR open to EGRVR solenoid
D.P.F. EGR sensor hoses both off
D.P.F. EGR sensor hoses reversed
Damaged EGR orifice tube
Damaged EGRVR solenoid
Damaged PCM

Perform KOER self-test and look for DTC P1408 as an indication of a hard fault. If P1408 is not present, look for contamination, restrictions, leaks, and intermittents

P1401 - DPF EGR Sensor Circuit High Voltage Detected
The EGR monitor checks the DPF EGR sensor signal to the PCM for high voltage. The test fails when the average voltage to the PCM goes to a voltage greater than the maximum calibrated value.
DPF EGR circuit open
VREF short to PWR
Damaged DPF EGR sensor
DPFEGR circuit short to PWR
SIG RTN circuit open
Damaged PCM

A DPF EGR PID reading greater than 4.5 volts with the key ON and engine OFF or running, indicates a hard fault.


Hope this helps (remember to rate and send us your comments about this answer).

May 22, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Need to find out what the emissions read P1401


P1401 - DPFE Circuit High Input

Description Of The Code:
The EGR monitor checks the DPF EGR sensor signal to the PCM for high voltage. The test fails when the average voltage to the PCM goes to a voltage greater than the maximum calibrated value.

Possible Causes:
  • DPF EGR circuit open.
  • VREF short to PWR.
  • Damaged DPF EGR sensor.
  • DPFEGR circuit short to PWR.
  • SIG RTN circuit open.
  • Damaged PCM.

  • Possible Solution:
    A DPF EGR PID reading greater than 4.5 volts with the key ON and engine OFF or running indicates a hard fault.

    Jan 14, 2011 | 2001 Chevrolet Venture

    1 Answer

    Exhaust Gas Recirculation Flow Insufficient Detected 2002 Ford Crown Victoria LX The car works very good at 60 and I go 35 to city and then when we slow down to city speeds it will have little jerks and we...


    P0401 - EGR Flow Insufficient Detected The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
    • Vacuum supply
    • EGR valve stuck closed
    • EGR valve leaks vacuum
    • EGR flow path restricted
    • EGRVR circuit shorted to PWR
    • VREF open to D.P.F. EGR sensor
    • D.P.F. EGR sensor downstream hose off or plugged
    • EGRVR circuit open to PCM
    • VPWR open to EGRVR solenoid
    • D.P.F. EGR sensor hoses both off
    • D.P.F. EGR sensor hoses reversed
    • Damaged EGR orifice tube
    • Damaged EGRVR solenoid
    • Damaged PCM
    Perform KOER self-test and look for DTC P1408 as an indication of a hard fault. If P1408 is not present, look for contamination, restrictions, leaks, and intermittents.
    not likely the PCM, engine computer. they seldom go bad.
    report back findings.

    May 16, 2010 | 2002 Ford Crown Victoria

    1 Answer

    EGR EVP Sensor


    Right on top of the EGR, (Exhaust Gas Recirculation), valve, which is on top of the intake.

    Looks like this,
    http://fordfuelinjection.com/index.php?p=35

    Now, let's talk. The guy's and gal's at the auto parts stores, are just there to sell auto parts, not diagnose cars, pickup trucks, and so on. Nice that they try to help, but an ODB II scanner just shows generic information.

    What I'm stating by that, is that you could buy that expensive part, and this may not cure your problem, and/or you could damage your computer if the procedure isn't done correctly.

    The P1400 code states,
    1.DPF EGR signal circuit shorted to ground
    2.DPF EGR signal VREF circuit open
    3.DPF EGR sensor is damaged or has failed
    4.PCM has failed (Powertrain Control Module)
    5.TSB 4-3-1 contains repair information for this trouble code

    You need a scanner that is the NGR, (New Generation Star), or has the capability to read
    Ford Enhanced Data.

    This connects to the PCM in the harness. (It's located on top of the engine) If the procedure isn't done right, you can "Let the smoke out", of the PCM.
    You also have to reset the computer to clear the error code.

    I know shop time is expensive, but sometimes it leads to less expense in the long run.

    Apr 28, 2009 | 2000 Ford Taurus

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    193 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5470 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...