Question about Cars & Trucks

Open Question

2006 gmc sierra p0053

Which side is left - HO2S left cylinder bank, sensor 1

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 196 Answers

SOURCE: need to know where sensor 1 (oxygen sensor) on bank 1 is located

It would be on the left header pipe as you sit in the truck. Its the sensor in front of the cat

Posted on Jan 17, 2009

Ad
  • 41 Answers

SOURCE: trouble code 1131 lack of ho2s bank 1 sensor 1 switches sensor

if sensor indicates lean check the fuel trim if long term fuel trim is above +7 them test sensor with a piko lab scope or watch scan data and create a rich condtion by snping the throttle wide open and watch the sensor if it start to read around 700to 900mv its ok, then create a vacume leak and the sensor should read 100to 300mv i your sensor is in this range quickly its good with in 1to2 sec.

Posted on Mar 22, 2009

emissionwiz
  • 80668 Answers

SOURCE: Replacing bank 1 sensor 2 and bank 2 sensor 1 oxygen sensors

BANK ONE IS THE REAR BANK OF CYLINDERS AND TWO THE FRONT BANK

Posted on Jun 24, 2009

  • 9 Answers

SOURCE: 1999 GMC Sierra 5.3L knocking sound around Catalytic Conerters? ?

on my gmc i have 2 knock sensors and im not possitive if you have two or not under your intake mani but when i replaced both mine i got the same code of low input so i took the small needle out and wire brushed it clean and also traced and ran a new wire just to be safe and that solved my problem. as for bank 1,2 if it helps any my bank one is located engine side driverside and bank2 is engine side passenger side and 3 and 4 are underneath bed side. but you can see the sensors if you look real close near the headers. hope this helps
See less

Posted on Jul 02, 2009

  • 323 Answers

SOURCE: oxygen sensor confusion

1/1 is upstream sensor on the number 1 cylinder side, 1/2 is the downstream of the number 1 cylinder side, 2/1 is the upstream of the number 2 cylinder side, 2/2 is the downstream of the number 2 cylinder side. Hope this helps.

Posted on Aug 10, 2009

Testimonial: "sorry, I hit the submit testimonial button before thanking both of you who so promptly answered. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Recently - asked about OBD2 code 0053. Advised to check heater fuse B1S1but none is listed in the care manual or diagrams. Both O2 sensor fuses are good... What next?


O2 sensor's don't have a fuse , except for the heater circuit. PCM - engine computer supply's five volt's , signal return and ground . All are connected at the PCM . The fuse's you are calling O2 sensor fuse's are for the heater circuit . The PCM controls the O2 heater circuit by pulse width modulation ,do you know what that is .There is a transistor inside the PCM that toggles the ground on an off to control the heater circuit . Unless you know automotive electrical circuit testing an testing PCM input's an outputs ,your best bet , take your vehicle to a qualified repair shop .

Pulse width modulation Pulse width modulation

Oct 25, 2017 | Cars & Trucks

2 Answers

I have a 5.3L 2005 Silverado and am getting odb 0053, 135, 449


• DTC P0053 HO2S Heater Resistance Bank 1 Sensor 1
The heated oxygen sensor (HO2S) must reach operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensor to reach operating temperature. Voltage is provided to the heater by the ignition 1 voltage circuit through a fuse. With the engine running, ground is provided to the heater by the HO2S heater low control circuit, through a low side driver within the powertrain control module (PCM). The PCM commands the heater ON or OFF to maintain a specific HO2S operating temperature range. The PCM determines the temperature by measuring the current flow through the heater. When the heater is in the ON state, the PCM will pulse the heater OFF for a duration of 50 ms, once per second. When the heater is in the OFF state, the PCM will pulse the heater ON for a duration of 50 ms, once per second. The PCM calculates the heater resistance on a cold start. This diagnostic will only run once per ignition cycle. If the PCM detects that the heater calculated resistance is not within an expected range, DTC P0053 sets for HO2S bank 1 sensor 1, or DTC P0059 sets for HO2S bank 2 sensor 1.

Turn ON the ignition, with the engine OFF.
Command the HO2S heaters ON with a scan tool.
Wait 15 seconds to allow the HO2S heater current to stabilize.
Observe the affected HO2S heater current parameter with a scan tool.
Is the HO2S heater current parameter within the specified range?
0.25-3.125 A
Inspect the O2A fuse.
Is the O2A fuse open?

DTC P0135 HO2S Heater Performance Bank 1 Sensor 1

Conditions for Setting the DTC
• The PCM detects that the affected HO2S Heater current parameter is greater than 3.125 amps or less than 0.25 amps.
• The above condition is met for 10 seconds.

Could be the Heater inside is open or a fuse problem , check fuse first , if you have not already done so.
Bank 1 sensor 1 is located on left side of the engine in the exhaust pipe before crossover

Oct 24, 2017 | Cars & Trucks

1 Answer

06 Chevy Silverado code p0053 and p0135


DTC P0053 HO2S Heater Resistance Bank 1 Sensor 1
• DTC P0135 HO2S Heater Performance Bank 1 Sensor 1
Important: Whenever the heated oxygen sensor (HO2S) heaters are commanded ON with a scan tool, they will continue to be pulsed ON once per second until the ignition is turned OFF for 30 seconds.
Turn ON the ignition, with the engine OFF.
Command the HO2S heaters ON with a scan tool.
Wait 15 seconds to allow the HO2S heater current to stabilize.
Observe the affected HO2S Heater Current parameter with a scan tool.
Is the HO2S Heater Current parameter within the specified range?
0.25-1.375 A

Sep 10, 2016 | 2006 Chevrolet Silverado

2 Answers

What is p0053 on a 2005 buick


Take the vehicle to Auto Zone or one of the other auto parts dealers and they will check it for FREE. They can advise you what to do.

0053 HO2S Heater Resistance Bank 1 Sensor 1
p0305 Cylinder 5 Misfire Detected
p0449 Evaporative Emission Vent Valve Solenoid Malfunction
u0107 Lost Communication With Throttle Actuator Control Module

Aug 23, 2015 | Buick Terraza Cars & Trucks

2 Answers

Trouble code p0134, p0135 p0053 p0030


P0134 - O2 Sensor Circuit No Activity Detected Sensor 1 Bank 1
P0135 - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
P0053 - O2 Heater Resistance Bank 1 Sensor 1
P0030 - O2 Heater Control Circuit Bank 1 Sensor 1
You need to replace the O2 Sensor Bank 1 Sensor 1
Carquest can help you get the correct part and help you locate it.

Apr 01, 2014 | 2006 GMC Envoy Xl

1 Answer

Replaced 02 sensor with code 131 and 171 now getting p0053


Code 53 is for a problem with the heater in the O2 sensor for bank one sensor one. It could be something in the wiring or you could have a defective sensor.

Jan 13, 2013 | 2005 GMC Sierra

1 Answer

These are the codes i got p0030, p0053,p0302,p0053, p0054,p0134


Hi,

Code explanations as follows:

P0030 = HO2S Heater Control Circuit (Bank 1 Sensor 1)
P0053 = HO2S Heater Resistance (Bank 1, Sensor 1)
P0054 = HO2S Heater Resistance (Bank 1, Sensor 2)
P0134 = 02 Sensor Circuit No Activity Detected (Bank 1, Sensor 1)
P0302 = Cylinder 2 Misfire Detected


Cheers,




"If this has helped you, please rate this solution"

Nov 01, 2011 | 2005 Chevrolet Equinox

1 Answer

I have a 97 gmc sierra 4x4, 5.7 engine. it is throwing a code bank 2 sensor 2. well i have 2 rear sensors, which one is it?


Bank 1 is side where #1 cylinder is, bank 2 is where # 2 cylinder is. Sensor 1 is before cat, sensor 2 is after. So, passenger side after cat.

Apr 15, 2011 | 1997 GMC Sierra

1 Answer

My 99 gmc sierra 2500hd has a bad o2 sensor sensor 1 bank 2 is that pass side front


bank 1 always refers to the bank that the No.1 cylinder is located and bank 2 is the other bank. Senspr 1 refers to the upstream oxygen sensor ( before the catalytic converter) sensor 2 refers to the downstream o2 sensor(after the cat) So if your No.1 cylinder is on the left side(drivers side) then your assumption is correct.

Jul 05, 2010 | Cars & Trucks

1 Answer

My check engine light has come on in my 2006 Pontiac G6 after 2 and a half years. What could possibly be wrong since I keep my car serviced and the guys had just told me that my car was in tip top shape?


P0016 - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A
P0030 - Heated Oxygen Sensor (H02S) Heater Control Circuit Bank 1 Sensor 1
P0031 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 1
P0036 - Heated Oxygen Sensor (HO2S) Heater Control Circuit Bank 1 Sensor 2
P0037 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 2
P0050 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 1
P0051 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 1
P0053 - HO2S Heater Resistance Bank 1 Sensor 1 (PCM)
P0054 - HO2S Heater Resistance Bank 1 Sensor 2 (PCM)
P0056 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 2
P0057 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 2
P0068 - Throttle Body Airflow Performance (PCM)
P0100 - MAF Sensor Circuit Insufficient Activity

Jun 25, 2009 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...