Question about 2007 Chrysler Aspen 4x2

Open Question

2007 chrysler aspen O2 sensor error code

Replaced o2 sensor, error code still on

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: Chrysler LHS o2 sensor testing

If u know u have a bad o2. I guess u must have used a scanner or equivalent. There are 4 o2s on LHS. The way u can tell the difference is by the # sequence that the failure code is giving u. For example the o2s on the right side are even # on the left odd #. Pre cat is 1 after cat is 2. So if u have bad 2/2 Than u know it's right rear or a bad 1/1 is left front ect ect. First make sure u have the right code. With out a scanner. it can be done with a volt meter or a vantage, but it's a heck of a lot easier pulling the codes.

Posted on May 15, 2008

Ad
deanam
  • 15 Answers

SOURCE: 2003 Chrysler 300m check engine light staying on

The only way, for shure is to go to computer diagnostics. 99% sure that this is some engine sensor, buy only diagnostics will tell who. (130,000 miles, hm lamda. it have only 150,000km live)

Posted on Apr 28, 2009

pippall
  • 1486 Answers

SOURCE: 2003 chrysler 300m o2 sensor and camshaft position sensor

SOUNDS LIKE YOU HAVE CAMSHAFT DAMAGE.

Posted on May 30, 2009

YIRMASTER
  • 32 Answers

SOURCE: I have a 2001 Chrysler Sebring LXI Coupe 3.0 mitsu

A great tool to have that can save you some money to read computer error codes and clear them after work has been done can be had for under $100 from Actron. This is what I have been using and its a life saver but it's also good to have the vehicles repair manual as well.

The computer on this car is OBDII like many other vehicles out there these days so you'll need a tool that can plug in and read the outlet located above the shin of your right leg under the dashboard or steering wheel. Here is a link to a bunch of their products on amazon Actron and other OBDII Computer diagnostic code reader tools.

Posted on Jan 11, 2010

  • 615 Answers

SOURCE: '05 PT Cruiser O2 sensor problems.

I had a similar problem with my car. It turned out the O2 sensors were fine and the issue was a leak in the throttle body causing the engine to run lean. If you have an ODB2 scanner you can look at fuel trims, etc and will be able to tell.

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2007 jeep commander code P0153 O2 sensor slow response( bank 2sensor 1) replaced O2 light came back on later that day same code replaced O2 sensor again later that day check engine back on


What type O2sensor did you use ? Aftermarket ? Jeep's ,Chryslers , dodge are picky . WARNING Aftermarket Oxygen Sensors Chrysler part 1 Did you test or just replace the O2 sensor . P0153 Jeep O2 sensor 2 1 Slow Response If you don't have the tools like this guy uses an have the know how it's tough to fix problems like this .

Mar 24, 2016 | Jeep Cars & Trucks

1 Answer

What does error code P0040 mean on a 2004 Chrysler Sebring touring


O2 sensors connections for the front sensors are swapped, open (cut) or shorted out. The PCM may be bad if the sensors and wiring are ok.
If you recently worked on the sensors check your wiring. If not, You probably have a bad O2 sensor or the wiring is at fault.

Sep 15, 2015 | 2004 Chrysler Sebring

1 Answer

Ok I have a 2007 Chrysler aspen, it gives me code p0052 bank2 sensor 1 I changed it and it still says the same thing. I looked on my scan tool and that sensor is has no heat temp. I've looked every where...


Well code 52 means the O2 sensor heater circuit resistance or voltage is too high. That could be a wiring problem or something else. You would need the troubleshooting chart for that code from the shop manual to find the actual problem.
The missfire codes would be something different, probably fuel or spark.

Mar 24, 2015 | Chrysler Cars & Trucks

1 Answer

Ambient temperature sensor 2007 chrysler aspen


Check for shorts, replace sensor... or just open the window and find out for yourself. :)

Mar 24, 2014 | 2007 Chrysler Aspen 4x2

1 Answer

Crysler aspen


O2 (B2 S2) Heater Circuit High (B2 S2 means bank 2 sensor 2)

Sounds like the rear O2 sensor on the passenger side is bad or unplugged.

Jan 28, 2014 | Cars & Trucks

1 Answer

Bank 1 sensor 1 on a 5.7 hemi


Driver side o2 sensor, before the catalytic converter

Jan 13, 2013 | 2008 Chrysler Aspen

1 Answer

2007 chrysler aspen at idle, rpm's fluctuate erraticly.why?


You probably have a bad throttle position sensor.

Sep 20, 2012 | 2007 Chrysler Aspen 4x2

2 Answers

I have a 2007 Nissan Xterra. Check engine light is on, gas cap gasket has been replaced and the O2 sensors are being replaced tomorrow. Today it would hesitate/slow acceleration when at 40-60mph (2000...


if you have an O2 sensor faliure you will have a code for it. in fact youe exterra doesnt have O2 sensors. it has A/F sensor or "air/fuel sensor" if it went bad, than you will have a code for that sensor. What is the code number that you have?? need to start there.

Oct 09, 2011 | 2007 Nissan Xterra Off Road

1 Answer

On my 1998 crysler sebring I am getting OBD II codes of 40 and 41,Transmission & engine module,any suggestions where to start? Thanks.


code 40-
Possible causes - 1/1 And 2/1 O2 sensors harness circuit shorted
- 1/1 And 2/1 O2 sensors harness circuit connectors (wrong connection)
- Faulty Powertrain Control Module (PCM) P0040 CHRYSLER Description At ignition on the Powertrain Control Module (PCM) checks the voltage on the ground side of the O2 sensor harness connector. If voltage is higher than two volts the P0040 code will set. code 41- Possible causes - 1/2 And 2/2 O2 sensors harness circuit shorted
- 1/2 And 2/2 O2 sensors harness circuit connectors (wrong connection)
- Faulty Powertrain Control Module (PCM) P0041 CHRYSLER Description At ignition on the Powertrain Control Module (PCM) checks the voltage on the ground side of the O2 sensor harness connector. If voltage is higher than two volts the P0041 code will set.

Dec 01, 2010 | 1998 Chrysler Sebring

1 Answer

I have a 2005 Chrysler Town & Country with almost 100,000 miles. The check engine light came on about 2 months ago and the code said the O2 sensors needed to be replaced. About a month later, the...


there are no codes that say replace O2 sensors,or remove converter,Thats just somebody's guessing,When it says O2 sensor that tells the mechanic to look for trouble in that area,wiring or faulty readings,And there are four O2 sensors.

Jan 20, 2010 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2007 Chrysler Aspen 4x2 Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...