Question about Cadillac Escalade EXT

Open Question

2007 escalade service stabilitrak message vechicle shuts down

Service stabilitrak icon comes on,traction control message also appears,next engine power is reduced message appears..vechicle shuts down.its happened in reverse parking,as it accelerates at a green light like it did tonight,shutting down.extremely dangerous as my wife and I were on a busy hwy!!!

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 35 Answers

SOURCE: Service Stabilitrak-Reduced Engine Power

the engine light is a generic fault indicator in your car to point out something is not quite right with the engine, having a loss of power as well is also known in some areas as Limp Mode or Safety Mode. it means the car is restricting the power it gives to ensure no damage it done to the engine.

the only certain way to find out what is wrong is to take it to a garage that has diagnostics equipment that can read the fault codes from the vechicles ECU (the fault codes will be the reason the light on the dash has come on as its reporting a fault somewhere)..

your mechanic should be able to tell you what is wrong with the engine from that and give you a more accurate cost at fixing it.

Posted on Dec 29, 2009

  • 714 Answers

SOURCE: The "engine power is reduced" light comes on

po455 is Probable Cause[s]

1. Defective, loose or missing fuel cap
2. EVAP canister broke, hose cracked or not connected
3. Purge or vent solenoid defective
4 . Vacuum leak at engine po121 code po121 means Throttle Position Sensor/Switch A Circuit Range/Performance Problem . it is usually indicative of a faulty throttle position sensor or faulty wiring harness in the engine bay.

Posted on Feb 27, 2010

tunde007
  • 2382 Answers

SOURCE: my engine light came on

Hi, the check engine light is the summary of the problem you are facing with the truck.

The "Check Engine" light means THERE IS A PROBLEM with either engine performance and/or emission controls and should be repaired ASAP. This light DOES set codes in the computer and can be scanned with an OBD2 scan tool. Most auto parts stores and auto zone will do this as a free service. When you get the code, it will be interpreted to know the exact problem with the car so it can be repaired...

Posted on Apr 19, 2011

wyet_helps
  • 339 Answers

SOURCE: my 2007 have a stabilitrak on and service traction...

I would advise to take it to a shop you trust and let them scan your vehicle for trouble codes. From there they can give you an idea as to why these messages appeared. : )

Posted on May 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I keep getting a message service stabilitrak


StabiliTrak Indicator Light: If the warning light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your StabiliTrak system and your vehicle may need service. When this warning light is on, the system is off and will not limit wheel spin. Adjust your driving accordingly.

This light will also flash when the StabiliTrak system is active. If the StabiliTrak system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service.

The traction control part of StabiliTrak can be turned off by pressing and releasing the StabiliTrak button if both systems (traction control and StabiliTrak) were previously on. To disable both traction control and StabiliTrak, press and hold the button for five seconds.

Traction control and StabiliTrak can be turned on by pressing and releasing the StabiliTrak button if not automatically shut off for any other reason.

When the TCS or StabiliTrak system is turned off, the StabiliTrak light and the appropriate TCS off or StabiliTrak off message will be displayed on the DIC to warn the driver. Your vehicle will still have brake-traction control when traction control is off, but will not be able to use the engine speed management system.

If the StabiliTrak and/or Traction Control are not operating properly, I encourage you to take your vehicle in for inspection. A certified technician will be able to offer a more accurate diagnosis.

Apr 29, 2015 | Cars & Trucks

1 Answer

2010 chevy 1/2 pick-up 4x4 Check engine light comes on, engine power reduced, and service stabilitrak, traction control off.


Since all three systems work together, when the engine light is on the other two can be also.
I would start with checking the engine computer for trouble codes.

Feb 06, 2014 | 2008 Chevrolet Suburban

1 Answer

What is an average cost to service the Stabilitrak System in a 2002 Cadillac Escalde


If the system fails to turn on or activate, the StabiliTrak light along with one of the following messages will be displayed on the Driver Information Center (DIC): TRACTION CONTROL OFF, SERVICE TRACTION CONTROL, STABILITRAK OFF, SERVICE STABILITRAK. If these DIC messages appear, make sure the StabiliTrak system has not been turned off using the StabiliTrak on/off button. Then turn the steering wheel clockwise from the nine o'clock position to the three o'clock position. If this clears the message(s), the vehicle does not need servicing. If this does not clear the message(s), then turn the vehicle off, wait 15 seconds, and then turn it back on again to reset the system. If any of these messages still appear on the DIC, the vehicle should be taken in for service.

Mar 17, 2013 | Cars & Trucks

1 Answer

Tow messages appear on the dash board: Service traction control and Engine power reduced. When this happen I can feel the shift in the transmission when I'm driving. After a while these messages d


Pretty much tells you the system with the fault

Traction Control is embedded into the abs braking
system, so diagnose that using the codes you have,
same as any other obd codes you get

The Reduced Power could be another problem & it
cuts off fuel injectors to save the exhaust converter
from overheating & being ruined

Mar 10, 2013 | 2009 Chevrolet Impala

4 Answers

My service stabletrack keeps come on how to fix that


Hi there:

Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.


Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.


When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.


When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.


You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.


Hope this helps.

Jun 03, 2012 | 2006 Chevrolet Blazer

1 Answer

I have a wrench with a car swerving light up every once in awhile but I have no idea what it means and I have no idea what stabilitrak is


{: ) A car swerving light on the instrument cluster is the StabiTrak indicator, sometimes called the traction control indicator. A wrench beside it tells it requires servicing.

Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.
Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.
When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.
When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.
You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.

Jan 25, 2011 | 2006 Chevrolet Trailblazer

2 Answers

We keep getting a message stabilitrak off, service stabilitrak then low engine power and I can't go above 40mph. Sometimes it clears after I turn off the vehicle and sometimes I can't drive it for a day....


I AM HAVING THE SAME PROBLEM BUT MINE ONLY COMES ON WHEN I AM IN GEAR, IDLEING AT A STOPLIGHT OR IN A DRIVE THRU. TOOK IT TO GM AND THEY ARE TELLING ME IT IS A "P0300 AND P0301" CODES WHICH SAYS IT A VALVE TRAIN MIS-FIRE ( TO FIX IT IS A 2000.00 HEAD JOB) AND THAT IS WHY THE STABILITRAK AND ENGINE LIGHT COMES ON!!! IN MY RESEARCH SO FAR I HAVE FOUND NOTHING THAT TIES THE TWO TOGETHER.
I HAVE 102,000 MILES ON MINE AND IT RUNS PERFECT AND MPG IS THE SAME AS THE DAY I GOT IT. I WILL KEEP YOU UP ON WHAT FURTHER I FIND. I AM NOW IN CONTACT WITH THE GM DISTRICT SUPERVISOR.

Mar 08, 2010 | 2007 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,824 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...