Question about 2004 Pontiac Grand Prix

1 Answer

Wet floor in 2000 pontiac grand prix driver side

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Check the plastic cover below windshield..where wipers are at.. theres a seal that leaks water under there and runs down fire wall to the floor.had that problem before myself

Posted on Feb 18, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

StormStrikes
  • 104 Answers

SOURCE: I need a wiring diagram for my 2000 pontiac grand prix

I own a 2001 Pontiac Grand Prix GTP and may be able to help you out if you let me know what specifically you are looking for.

Posted on Jan 02, 2009

  • 83 Answers

SOURCE: 2000 pontiac grand prix se ecm location

located in air box beather box for intake.

Posted on Jan 13, 2009

  • 6982 Answers

SOURCE: Pontiac Grand Prix Drivers side window won't go down

Most often on those the motors are shot. as soon as they are activated they overheat and slow down or stop. Only way I know of to repair is to replace them. You will need a manual to do this or do them one at a time so you can check how it goes back together by looking at other one. Motors are riveted in and need to be drilled to remove...use small bolts to re-attach.
I've seen motors online for about $30-40 each.

Posted on Aug 28, 2009

  • 1 Answer

SOURCE: How do I change the low beam bulb(drivers side) on

Upside down L shaped bracket that is bolted to frame just behind headlight assy. Unbolt bracket, lift bracket straight up to unlock headlight assy. Headlight assy should easlier fall forward to replace any of the 3 bulbs

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the firing order for a 2000 Pontiac Grand Prix 3.1L ?


Firing order for 2000 Pontiac GP 3.1L.....Driver side...1,3,5......Passenger side....2,4,6.

Aug 28, 2014 | 2000 Pontiac Grand Prix

1 Answer

1999 Pontiac Grand prix does not blow high fan speed on Max A/C.


if its the same set up as my oldsmobile intrigue there is a plug behind the glove box that has a sensor board, my fan quit working all together and I swapped that sensor out and everything worked fine afterwards, does your right side passenger floor board get wet when it rains hard, if so it has shorted part of the sensor out for the high side of the fan.

Sep 11, 2013 | 1999 Pontiac Grand Prix

1 Answer

WATER INSIDE 2004 PONTIAC GRAND PRIX


Check A/c drain clogged, back side globe box.

Mar 26, 2012 | 2004 Pontiac Grand Prix

1 Answer

Floor wet on the passenger side of my 2002 pontiac grand prix


your air conditioning drain is probably stopped up.the drain is located on the passenger side along the firewall.

Apr 29, 2011 | 2004 Pontiac Grand Prix

1 Answer

Power windows in 2000 grand prix


driver side window stopped working motor works all other windows work

May 14, 2010 | 2000 Pontiac Grand Prix

1 Answer

2003 Pontiac Grand Prix - A/C not cool on driver's side


You would need to buy a factory service manual for that blend door diagram. Try eBay for a used manual set.

Aug 22, 2017 | 2003 Pontiac Grand Prix

1 Answer

2006 pontiac Grand Prix stalls in wet weather


A cause for that would be an oxygen sensor getting wet, the one on the inlet side of the catalytic converter.

Apr 15, 2009 | 2006 Pontiac Grand Prix

3 Answers

2000 grand prix leaking on drivers side floor board


Sell the car if will only get worse from here. I have had nothing but trouble from my 1999 grand prix. Will never own another Pontiac

Oct 25, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
2004 Pontiac Grand Prix Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...