Question about Cars & Trucks

Open Question

How to adjust the idle on a 1982 corvette - Cars & Trucks

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: my 1982 corvette crossfire misses and stalls 6000

i would clean the injecters

Posted on Sep 22, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are the three wiper connections on the wiper motor of a 1981 corvette

ground,high,low, heres a diagram for testing.

Sep 04, 2017 | Cars & Trucks

1 Answer

What are the lug nut torque specs for a 1975 corvette stingray?

For 1965-1982 Corvettes
rally wheels (steel) are 75ft/lbs.
optional wheels (alumiminum) 80ft/lbs. retorque every 100 miles

Aug 04, 2014 | Cars & Trucks

1 Answer

No gas from my 1982 vette fuel sender unit been replace

Check all the ground wires Corvettes have big problems with grouunds

May 28, 2014 | 1981 Chevrolet Corvette

1 Answer

I need a diagram to install a 1971 corvette gas tank. I need to see how the straps hook up.

The guys on the Corvette Forum can help you with that. Refer: ,,,,,,,,,,,,,,,

Sep 15, 2011 | Chevrolet Corvette Cars & Trucks

2 Answers

1981 corvette carb adjustments 4 bblr feadback q-jet need idle adjust proceedure

the idle adjustment needs to be performed warm but the mixture screws at or near the base have springs on then they need turned in all the way and backed out 2 turns then when the vehicle is warm the idle screw is near the linkage also with a spring on it if you have a tach in the car it should its a corvette lol turn the screw in or out until the car idles around 750 to 850 rpm it idles up automatically when cold if your choke is set properlythis should get you where you need to be you may need to adjust mixture screws a little the only proper way to do this is with a vacuum box but you will be in the ballpark anyway with the method i gave you

May 06, 2010 | 1981 Chevrolet Corvette

1 Answer

1982 corvette. after setting off alarm, reset the alarm and now the starter won't engage. Why doesn't the relay that deactivates the solonoid reset?

because the car thinks its stolen you need to goto a garage i dont think a keyless entry was available on it so that wouldnt help

Apr 02, 2010 | 1981 Chevrolet Corvette

1 Answer

Looking for info on how to adjust the fuel mixture and Idle on a 1969 Corvette 427 400 HP Tri-power 3x2 carburetor.

That engine runs at low speed, starts and idles on the center carb only. first make sure the carbs are synchronized so the front and rear ones are fully closed at idle, then adjust idle speed and mixture on the center carb. Sweet ride by the way, if you get tired of working on it and want to get rid of it I will take it. LOL

Feb 22, 2010 | 1965 Chevrolet Corvette

1 Answer

Idle is too high ,have replaced the idle control motor and correcly set the T P S.

when you put new idle speed control in you have to adjust it to make it work.if all is good. your throttle valve sticking open.due to gum and carbon build up around valve.or your throttle cable need adjusting.could be out of adjustment..

Jul 13, 2009 | 1987 Chevrolet Corvette

1 Answer

I have an 1982 f 250 4.9 and go through carburaters a lot. New ones last may be a year then start burnning way to much gas. The carb has an idle adjustment and a curb idle adjustment no air gas mixture...

1982 ?? their wouldnt be any adjustment as they are fixed jet carbs ,you could try fitting new jets but whats causing them to eat away in the first place i dont know unless its the fuel additive that you have to add to the unleaded fuel

Jul 12, 2009 | 1982 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides