Question about 1988 Acura Legend

1 Answer

Driver seat removal

Trying to remove the drivers seat of my 1988 acura legend

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

There are four bolts (2 in ft ,2 in rear)that bolt seat to floor. you will need slide seat all the way forward to access rear bolts, they may ,if they are still there, be under plastic beauty caps. do the same for ft bolts. once loose tillt seat assy backwards and unplug any wiring connectors on bottom f seat

Posted on Feb 02, 2009

1 Suggested Answer

mas66
  • 104 Answers

SOURCE: removal of the driver seat of my 1988 acura legend

I'm not certain of the layout of the bolts on your particular model, but there should be 4 bolts, one at each end of the seat tracks (the things the seat slides back and forth on), attaching the tracks to the floor. You may need to slide the seat back to access the front bolts, and forward again to get the back ones. Tilt the seat back right forward to allow you to get the seat out the door. If the seat has electric controls there will be some plugs to disconnect under it. If there are any yellow coloured plugs, DO NOT disconnect them without disconnecting the negative terminal off the battery and waiting for 5 minutes. The yellow plug is an airbag system plug, and if the battery is not disconnected the airbags could potentially deploy. Make sure the battery remains disconnected for the entire time that the yellow plug is disconnected, and reconnect the battery AFTER the yellow plug. If there isn't a yellow plug, don't worry.

Hope this helps.

Posted on Oct 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the starter on my 1993 Acura Legend?


Hi Gayle,here's a Autozone repair guide on replacing your starter,once off,have Autozone test it to see if it's bad,they will need it on a trade in,core.They test it for free,take's only a few minutes. SAVE 20 GET 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Also here's something else to look at.

Starter Cutoff Relay

1993 Acura Legend 3.2L FI 6cyl

The Starter Cutoff Relay is located: Front seating area, driver side, under dash, mounted in fuse block.

Jul 28, 2015 | 1993 Acura Legend

1 Answer

1993 honda acura legend removing power left side


if your removing the seat there are 4 bolts that secure the seat rails to the floor of the car these are what the seat moves back and forth on, that need to be removed then find the electrical connector and unhook then remove the seat.

Aug 27, 2014 | 1993 Acura Legend

1 Answer

How to replace the driver seat motor?


un plug the motor and take a voltage motor and check for voltage at the plug

Apr 08, 2010 | 1988 Acura Legend

2 Answers

How to replace fuel pump on 1992 acura legend


Remove and check for a access door under the back seat.

Jul 19, 2009 | 1991 Acura Legend

1 Answer

Clearance to remove 93 Acura Legend starter


you can either remove driver's side halfshaft or battery tray and alternator to remove the starter. i chose the halfshaft, since it gave a little more room to unbolt the starter. no need to drain transaxle when removing driver's side halfshaft. unbolt balljoint and tierod end from knuckle. i also removed the pinch bold that attaches the strut to the knuckle to allow more movement to remove the axle. axle nut is 36mm. use a large screwdriver or small prybar to gently pry the halfshaft from the transaxle, be careful not to damage the seal. upper bolt on the starter is really tough to get access to...

Apr 20, 2009 | 1993 Acura Legend

1 Answer

Removal of the driver seat of my 1988 acura legend


I'm not certain of the layout of the bolts on your particular model, but there should be 4 bolts, one at each end of the seat tracks (the things the seat slides back and forth on), attaching the tracks to the floor. You may need to slide the seat back to access the front bolts, and forward again to get the back ones. Tilt the seat back right forward to allow you to get the seat out the door. If the seat has electric controls there will be some plugs to disconnect under it. If there are any yellow coloured plugs, DO NOT disconnect them without disconnecting the negative terminal off the battery and waiting for 5 minutes. The yellow plug is an airbag system plug, and if the battery is not disconnected the airbags could potentially deploy. Make sure the battery remains disconnected for the entire time that the yellow plug is disconnected, and reconnect the battery AFTER the yellow plug. If there isn't a yellow plug, don't worry.

Hope this helps.

Oct 26, 2008 | 1988 Acura Legend

1 Answer

Back seat of 89 acura legend


well the is a couple ways to fix it, first you can take out the seat cushion and reach behind and its a done deal, or you can crawl through the trunk to the seat and do it that way.

Jun 19, 2008 | 1989 Acura Legend

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...