Question about 1995 Mitsubishi Eclipse

1 Answer

Turn signals stopped working

I purchased the vehicle used and the turn signals were working but have stopped working. The hazards were not working while the turn signals were working. I checked the fuses and found one had blown out. I replaced it and the turn signals are still not working.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Sounds like the flasher is out. Really cheap fix. New ones are about $5-10.

Posted on Feb 17, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you locate and test flasher relay on a 2006 Chevy Equinox? Turn signals and hazards stopped working after changing audio system. Fuses test good. Thank you, Mike


Did you change any wiring , tap into any wiring ? There is no flasher relay on your vehicle . It controlled by the BCM !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
Your best bet , take it to a qualified repair ! We on here have no clue what you did . On this newer vehicles ,if you know nothing about automotive electronics you really should take to a professional

Aug 10, 2017 | Cars & Trucks

1 Answer

I just bought the car the turn signals work in the front but not in the back whats the problem?


Have you checked the bulbs already?
Don't know what kind of car you are dealing with here.
Most vehicles - the brake lights and rear turn signals share the same electrical circuit to the rear tailights. Usually the turn signal switch will separate which signal goes to the back.
Do your brake lights work? Is there a High mounted stop lamp and does it work?
I have seen a Hazard Switch be ON and fuse blown causing the Hazard Flasher to be inop - which prevented the turn signals from working. Turning OFF the hazard flasher brought back the T/S.
Check the rest of the lights - see what does and doesn't work - and do the front turn signals flash? Stay On? Or flash really slow?
Let me know what you find out and if this helps you at all.

Mar 12, 2015 | Cars & Trucks

1 Answer

Hasards dont come on on a 2000 isuzu trooper


No need to panic-this can SEEM TO be caused by a couple of things, but it is fairly simple to determine exactly what is causing this flasher circuit condition.
First, turn on your flashers, however you have to do it, and walk around the truck to check that all bulbs are working (at least one on each corner). Turn signal and hazard flasher relays are thermal circuit interrupters and are current sensitive and will not work properly with too few or too many bulbs in the circuit. (This is usually a big problem when switching over to LED lamps, as LEDs only draw a fraction of the current that the bulbs do. This causes the relay to either not flash at all or flash very fast and triggers warning circuits on newer cars) If there is one or more bulbs out, they must be replaced.
That being said, I doubt that alone is your problem. Here is a general automotive wiring primer aimed at the turn signal, hazard, stop, and running lights on most all motor vehicles.
Hazard flashers are required by D.O.T. safety standards on all motor vehicles that may ever be used anywhere near a public road. They are also required to be able to be used without the ignition key. This means the flasher circuit for hazards is fed thru a fuse that connects straight to the battery and is energized at all times.
Turn signal circuits often share the same flasher relay as the Hazards, even though the power for them is switched through the ignition key. Power for directional blinkers connects to a fuse, then the ignition switch, then to the battery.
So, if you have to turn on the turn signals (is the key on?) to get hazards to work, that means they are not getting power direct from the battery, but can get it when the turn signals are on because they both use the same relay. This is usually the case on all vehicles; If 4-way flashers and turn signal are both on at once, the 4-ways override the turn signal and force all signal bulbs to flash. The turn signal never forces one side of the hazards to stop blinking.
So, where does that leave us? You simply have a blown fuse, my friend. The hazard lamps fuse may also power the cigarette lighter, dome light, or other "always on" accessories. This varies with make & model, but the Hazard Lps fuse is usually well marked in the fusebox. If the fuse blows again shortly after being installed, do not put in a larger one! Try one more. If it also blows immediately, there is a problem with the wiring, or a bulb could be in wrong and shorting to the socket ground. Try removing all the flasher bulbs and trying the switch(it won't flash or "tick-tock") again. If the fuse does not blow, you have found the problem. Good hunting!

Apr 15, 2013 | 2000 Isuzu Trooper

1 Answer

After i hit someone from the back my left turn signals stopped working but the right side does work. Also the hazard signals on the left side do not work but the right does work. what should i do?


The wiring for your left turn/hazard might be damaged. The turn and hazard signals use the same bulbs and wiring, but get their signal from different switches.

Aug 08, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

My 2000 saturn sl2 turn signals stopped working


HI"
onepx.gif
onepx.gif onepx.gif Vehicles: onepx.gif Make/Models: onepx.gif Model/Build Years: SATURN/LS onepx.gif 2000 onepx.gif onepxblk.gif onepx.gif Defect: onepx.gif VEHICLEDESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES DO NOT COMPLY WITHREQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, ANDASSOCIATED EQUIPMENT." BECAUSE OF A PROBLEM IN THE HAZARD WARNINGSWITCH ASSEMBLY, THE TURN SIGNAL LAMPS MAY NOT WORK OR MAY WORKINTERMITTENTLY WHEN THE DRIVER USES THE TURN SIGNAL LEVER OR HAZARDWARNING SWITCH. IF THE VEHICLE TURN SIGNAL INDICATORS ARE NOT FLASHING,THEN THE TURN SIGNAL LAMPS MAY NOT BE FLASHING. onepx.gif onepxblk.gif onepx.gif Component Affected: onepx.gif EXTERIOR LIGHTING:TURN SIGNAL:SWITCH onepx.gif onepxblk.gif onepx.gif Corrective Action: onepx.gif OTHER DRIVERS MAY NOT BE ALERTED THAT THE VEHICLE IS TURNING AND A CRASH COULD OCCUR. onepx.gif onepxblk.gif onepx.gif Consequence: onepx.gif DEALERS WILL REPLACE THE HAZARD WARNING SWITCH ASSEMBLY. onepx.gif onepxblk.gif onepx.gif Mfr. Campaign #: onepx.gif 99045/00-C-03 onepx.gif onepxblk.gif onepx.gif Mfr. Involved: onepx.gif GENERAL MOTORS CORP. onepx.gif onepxblk.gif onepx.gif # Vehicles Affected: onepx.gif 1395 onepx.gif onepxblk.gif onepx.gif File Date: onepx.gif 07/29/1999 onepx.gif onepx.gif onepx.gif onepx.gif onepx.gif
onepx.gif onepx.gif The vehicle you are working on may or may not be affected by this recall. Contact the vehicle manufacturer for clarification. hope this solves your problem.THANK YOU

Sep 23, 2009 | 2000 Saturn L-Series

1 Answer

1997 Chevy Tahoe both turn signals stopped working


Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Jul 21, 2009 | 2001 Chevrolet Tahoe

1 Answer

Turn signal switch


You likely have a sticking hazard signal relay or hazard switch. Try turning on the left or right turn signal then depressing and releasing the hazard switch a few times. If the lights begin working you probably have / had a sticking switch. They don't get used often and this is not uncommon. Also could be relay. Thats a cheap fix and easy to locate. Should be with fuse box or near it.

If this helps please rate my answers.
Brett

Mar 20, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
1995 Mitsubishi Eclipse Logo

399 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...