Question about 2001 Chevrolet Blazer

1 Answer

New key fob

Hi do you know how to program a new fob .thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just get in your vech , close all doors. Using your power lock switch , lock all doors. After doors are locked take your Ignition Key and insert it and remove it from ignition switch in a slow fashion , but consitant pace. (97 and earlyer are fast) When you see the hazzard lights flash, put key in ignition switch and turn to the On postion .. Do NOT CRANK or you will have to Start over .. After in the On postion .. Hit the Lock button on remote... Hazzard lights should flash..( note..you have to reprogram all remotes when adding a new one , if you don't your old remotes will not work ) If your doing just the one , turn igntion switch off and unlock door and get out and try it. If you are doing more than one. While still in Vech with Key on . After you hit the Lock button on Remote and hazzard light flashed .. with key still on .. use master lock switch unlock doors and relock and then hit Second Remote, Lights should flash again , repeat if adding a 3rd remote.. after done just turn key off and unlock door and get out and try. Good Luck :)new key fob - s.gif

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get a quick replacement key for my Honda CR-V. I have a 2006 Honda CRV, the key & FOB are separated. I need to repair or replace. I live in Philippines


You need to go to a Honda dealer for this as the new key has to be programmed to the car and you will not be able to do this yourself even if you buy a new original equipment key from another source.

Nov 13, 2015 | Honda Cars & Trucks

1 Answer

I have a Toyota Avensis 2007 1.6 and I want to know if my car have any feature with the key fob like open the windows with the key fob or any other feature! Thank you :)


I find the toyota owners forum very helpful on these type questions:
Programming Avensis T3 Key Fob Avensis Club

Unfortunately it doesn't look like there are any special features, most of the entries revolve around reprogramming if you have to replace or renew the batteries.

Jan 02, 2015 | 2007 Toyota avensis 1.6

1 Answer

Anti theft system/ keyless entry


The best way and probably the only way to program the key fob is to have it done in a dealer service centre . I know that it is expensive but they have the CPU in the car and your key fob and the pair are programmed together

Mar 18, 2014 | Mazda 6 Cars & Trucks

1 Answer

Got new key fob for my 2006 chevy malibu ss how do I program it to work


How to Program a Key FOB for the Chevy ' eHow.com

www.ehow.com/how_7508133_program-key-fob-chevy.html

How to Program a Key FOB for the Chevy ... your Chevy, if you obtain new or replacement keys they will need programming to work with ... How Do I Program MyKey Fob? ...

Mar 14, 2013 | Cars & Trucks

2 Answers

How do i program my ford key fob 2 my transit van


1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

Mar 22, 2012 | Cars & Trucks

1 Answer

Keyless entry remote programming


Hello here is the instructions for programming the key fobs

This procedure will add, replace, or invalidate all key fobs. This procedure requires that you have a known good key fob available, a new/replacement key fob, the vehicles mechanical key, and a scan tool.
Method 1 is also used for the initial programming of fobs to a new replacement RCDLR. In this instance, the new RCDLR comes ready to learn the first key fobs introduced. Perform the learn procedure as outlined, with the exception that the new RCDLR does not require a known good key fob be placed within the interior of the vehicle.
Note: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Methods 2 or 3 must be used in this instance.
  1. The vehicle must be OFF.
  2. Place a known key fob and any new/replacement key fob(s) to be programmed in the cupholder inside the vehicle. DO NOT place any fobs in the console fob pocket at this time.
  3. Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
  4. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4). → If the DIC displays: OFF/ACC TO LEARN, the known fob has not been recognized. At this time, programming will revert to Method 2.
  5. If the DIC is displaying the correct fob number that needs to be programmed, skip ahead to step 9.
  6. If the DIC is not displaying the correct fob number that needs to be changed (i.e., the DIC is displaying: READY FOR FOB 3, and you wish to program FOB 1), use the scan tool to access the following: • Vehicle Control Systems • Computer/Integrating Systems • Module Setup • Remote Control Door Lock Receiver • Program Key Fobs
  7. Select the fob position you wish to program: Note: Selecting Invalidate All Fobs will erase any known fobs and will cause the DIC to prompt READY FOR FOB 1, requiring all fobs to be relearned to the vehicle.
    • Invalidate All Fobs • Program Fob 1 • Program Fob 2 • Program Fob 3 • Program Fob 4
  8. With the fob position selected, press the PROGRAM soft key on the scan tool. The DIC should display: READY FOR FOB X (X = fob 1, 2, 3 or 4, depending on the selected position)
  9. With the DIC displaying the correct fob position that is to be programmed, place the new/replacement key fob in the console fob pocket with the buttons facing forward.
  10. A beep will occur once the fob has been learned.
  11. If programming additional key fobs and there is no DIC prompt that indicates READY FOR FOB X, repeat steps 7 and 8.
  12. Exit programming mode by pushing the OFF/ACC portion of the ignition switch. Note: Failure to exit programming mode (press OFF/ACC) prior to pressing the UNLOCK button of each key fob programmed will result in that fob being inoperative. Pressing the UNLOCK button completes the programming sequence and is require to ensure transmitter operation.
  13. Press the UNLOCK button on each key fob that was programmed to finalize the programming and confirm system operation.

Nov 03, 2010 | 2006 Cadillac STS

1 Answer

Key mob stopped working


the only TRUE way to program he key fobs is with a scanner

how are you programming the fobs w/o a scanner?

if you have trick..I'd like to know too since I already know I don't know it ALL!

May 19, 2010 | 2003 Lincoln Navigator

1 Answer

Key fob for my peugeot 206


Yes you can have multiple key fobs for one vehicle. They will need to be programmed. Some cars require that you program all key fobs at the same time and can only be done through a dealer scanner and some will have instructions in the owner's handbook.

May 16, 2010 | 1999 Oldsmobile Intrigue

1 Answer

Programming


you cannot program that fob to that car without a new ecu.

Oct 01, 2009 | Toyota Cars & Trucks

4 Answers

Code to program my key fob


Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode

Oct 25, 2008 | 1999 Oldsmobile Intrigue

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

515 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...