Question about 1998 Toyota Corolla

Open Question



Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: How do i replace my outside dorrhanle on my 1998 toyota corolla

You do need to pull off the inner door panel. After the panel is off, you are going to need to disconnect the lock rods from the outer handle and the key cylinder to the door latch mechanism. You will need a long 1/4" drive ratchet and extension, and a 10 millimeter socket. The outer handle is held on by 2 10 mm bolts, you access them thru the inner part of the door. There is a hole provided, with clear tape over it, that will lead you to the harder to see bolt. After the bolts are out, remove the handle, swap the key cylinder into the new handle, and reinstall. Not hard at all.

Posted on Dec 30, 2008

  • 2 Answers

SOURCE: removing door panel in 2000 toyota corolla

remove phillips scew and the door handle. remove padded arm rest on the door by lifting it up, and remove 2 screws. You can use a panel tool to remove the plastic toggle like pins holding the panel border in. Be as gentle as possible they may break due to becoming brittle.

Posted on Apr 06, 2009

  • 2187 Answers

SOURCE: Need Mfg tire-size for 1989 Toyota Corolla all-trac station wagon

Your wagon came with the same stock tires as the sedan.





Posted on Jun 25, 2009

  • 2976 Answers

SOURCE: rebuilding the front

The best thing you can do, that will make everything you will need available to you, is to buy a Chilton or Motor's manual. They have every nut, bolt, wire etc. They also give instructions on how to remove and install difficult parts.

Posted on Aug 28, 2009

  • 1986 Answers

SOURCE: P0136 code on 1998 Toyota Corolla?

The sensor will cost around $100 give or take a bit. The labour will be around $50 give or take a bit (30 min job according to estimate book)

you can also buy the sensor and change it yourself. It's the O2 sensor located after the catalytic converter

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replace front drive axle

Probable front end suspension damage that has put the wheel alignment out . To need to replace the axle and rim indicates that the strut an lower support arm will also be bent. Have the front end inspected and a wheel alignment done

Feb 01, 2014 | 1998 Toyota Corolla

1 Answer

1998 TOYOTA CORROLA. front end vibration at 50 mph on acceleration only. I grabbed hold of the drive axle just behind the cv boot near the tire. I can move it in and out a bit. oN TWO OTHER COROLLAS i HAVE...

I would definitely stay with tire balancing first. So much less expensive. Axle trouble is usually accompanied by noise which comes and goes with turning the wheel or braking.

Mar 17, 2010 | 1998 Toyota Corolla

1 Answer

Daughter hit curb,broke steering gear & other misc. parts. replaced steering box & other front end parts. while bocked up, put car in drive,passenger axle spins constant drivers random. replaced...

When both wheels are in the air it is normal that one wheel will not turn when put in gear.

There is nothing wrong with the axle or the transmission.

Feb 01, 2010 | 1998 Toyota Corolla

1 Answer

Fuse diagram of toyota corolla 1998

most fuse diagrams for toyotas are on the inside cover of the fuse panel whether inside the engine or mounted on firewall under dash on drivers side

Dec 22, 2009 | 1998 Toyota Corolla

1 Answer

Coil above rear driver's side tire is practically

Blown suspension. You need to replace the spring and check the suspension spring supports. Also check all the others front and rear.

Nov 04, 2009 | 1994 Toyota Corolla

1 Answer

My front tires on my car wear out on the inside

well na parts need replacing all you need is a alingment

Oct 28, 2009 | 1998 Toyota Camry

1 Answer

Rebuilding the front

The best thing you can do, that will make everything you will need available to you, is to buy a Chilton or Motor's manual. They have every nut, bolt, wire etc. They also give instructions on how to remove and install difficult parts.

Aug 28, 2009 | 1997 Toyota Corolla

1 Answer

How do you replace a high presure stering hose on a 1998 toyota corola?

there is a link on the drivers side behind the engine, you have to use a open ended wrench to get it free, i started by removing that side first, then took off the passenger side, using a open ended wrench as well. good luck! hope this helps

Apr 10, 2009 | 1998 Toyota Corolla

Not finding what you are looking for?
1998 Toyota Corolla Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides