Question about Cars & Trucks

Open Question

Replace evap two way valve on honda accord - Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2926 Answers

SOURCE: Evap Code 1457 on a

Before you replace these critical components, have you replaced the fuel/gas cap first?

Posted on May 19, 2011

Ad
fastboyz
  • 674 Answers

SOURCE: honda accord 96 exi

You need to discharge the AC system and remove the evaporator to replace the expansion valve. No two way about it.

No need to remove the dash

Posted on Aug 29, 2008

SOURCE: replace expansion valve

Hi Tresap,
The only expansion valve that I can think of that you may like to replace is on the air conditioning unit....This valve is found usualy mounted onto the AC unit....You'll have to remove the dash board and centre consul....This is qute a job....You should then see the expantion valve on the cabin side of the AC housing....where the pipes go thru into the engine compartment....NOW HOLD EVERYTHING.....before you can remove the valve you need to depressurize the AC unit....That should be done by an expert....The gas is dangerous and you must wear safety googles at ALL times....Once you have removed the valve, you must seal the system so that as little moisture as possible enters the system....If it is left open, you'll have to replace the dryer unit too....when you've finished your replacement, assembly is the opposite as disassembly.....You'll then need to have the system recharged....Don't try to engage it until that has been done....It wont work even if you tried ,as there are pressur switches which will inhibit the opperation....If you have had practice, it will take about three quarters of a day......if not, three or four days

Hope that this helps you

Best regards Johngee10

Posted on Sep 01, 2008

gh20s
  • 343 Answers

SOURCE: Need to locate PCV valve on 4cyl. Honda Accord

It should be on the valve cover. It should b "L" shaped and inserted into a rubber grommit and connected at the top is a vacuum line.

Posted on Apr 27, 2010

jgwhomeequip
  • 1902 Answers

SOURCE: 1997 Honda Accord, 4 Cl.

Sounds to me like you have either forgot to put back on the breather tube that runs off of the top of the valve cover, or, you did not set your valve cover correctly, or the torque is not correct on the cover itself.
8.7ft/lbs and the torque sequence is inside to outside (torque the inner-most nut between cyl 2 & 3 first, then the one above it then alternate sides on the outside ones). Recommended Hondabond is on the corners and the cam cap areas.

Posted on Jun 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the evap canister solinoid located at honda accord 2000


2000
why not post the DTC error for better answers/?
and country.?
now my answer from USA, cars.
1: in usa open hood, see vacuum sticker, its there.
2: in FSM there are 3, purge control and bypass VSV. and vent shut off VSV.
so which one. ill answer for all 3.
at the canister. (im looking ,in alldata.com so an you)
1: CAN , hose.
one goes to tank, directly not that hose.
2: hose 2. is vent shut valve top of CAN, and goes to Vent can filter.
3: hose 3: to purge joint then purge valve.
4: and last host to bypass valve. this valve has 3 hoses (unique)

alldata.com click evap emmissions tab.

Oct 25, 2013 | 1998 Honda Accord

1 Answer

Dtc p1457,0107


P1457 HONDA - Evaporative Emissions Control System Leakage EVAP Canister Systemxicon.jpghttp://engine-codes.com/p1457_honda.htmlForum CodePossible causes- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap There is a Honda factory service bulletin with information on how to diagnose the P1456 on the following Honda models:
1998 Honda Accord
1999 Honda Accord
2000 Honda Accord
1998-2000 Honda Accord
symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vaporsP1457 HONDA Description The evaporative emission (EVAP) control system stores fuel vapor from the fuel tank in the EVAP canister temporarily to prevent it from escaping to the atmosphere and to enable it to be drawn into the engine by intake manifold vacuum and burned. In addition, the onboard refueling vapor recovery system (ORVR) stores fuel vapor generated when refueling in the EVAP canister.

The EVAP control system leak detection method improves the accuracy and frequency of the detection by determining faulty components and vapor leakage for each part. The EVAP control system (from the purge valve to the fuel tank) is divided into two parts. One is the "EVAP Canister Side" (from the EVAP two way valve to the purge valve) and the other is the "Tank Side" (from the EVAP two way valve to the fuel tank). There is 0.04 inch leak detection and 0.02 inch leak detection. If the 0.04 inch leak detection results are OK, the 0.02 inch leak detection runs. The P1457 code is detected when the EVAP system has a very small leak.

P0107 HONDA - Manifold Absolute Pressure Sensor Circuit Low Voltagexicon.jpghttp://engine-codes.com/p0107_honda.htmlForum CodePossible causes- Manifold Absolute Pressure harness is open or shorted
- Manifold Absolute Pressure sensor poor electrical circuit connector
- Faulty Manifold Absolute Pressure sensor
- Faulty Engine Control Module (ECM) When is the code detected?An excessively low voltage from the sensor is sent to ECMSymptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Engine rough idle
- Engine hesitation
P0107 HONDA Description The Manifold Absolute Pressure sensor provides instantaneous manifold pressure information to the engine's Engine Control Module. The data is used to calculate air density and determine the engine's air mass flow rate, which in turn determines the required fuel metering for optimum combustion. A fuel-injected engine may alternately use a Mass Air Flow sensor to detect the intake airflow. A typical configuration employs one or the other, but seldom both.


In some vehicles the absolute pressure sensor is built into ECM. HONDA Technical Service Bulletins for P0107 code1999 HONDA ODYSSEY Electrical System 2000 HONDA ODYSSEY Electrical System1998 HONDA ACCORD Electrical System 1999 HONDA ACCORD Electrical System 2000 HONDA ACCORD Electrical System 2001 HONDA ACCORD Electrical System 2002 HONDA ACCORD Electrical System 1996 HONDA CIVIC Electrical System 1997 HONDA CIVIC Electrical System 1998 HONDA CIVIC Electrical System

Jul 25, 2012 | Honda Civic Cars & Trucks

1 Answer

Honda Accord EX 4 cyl. 1998 has troubleshooting which has the code P1457 . What is this ?


p1457 is an evap code. If you where to bring it to the dealer they would be able to run a complete evap system test and tell exactly what the problem is. I've run this test on over a 100 accords like this and 90% of the time the fault is in the cvs valve. (canister vent shut valve). Its located under the vehicle closer to the rear, on the side of the evap canister. the part runs approx. 100-175 dollars. Good luck hope this helps!

Dec 20, 2010 | 1998 Honda Accord

1 Answer

1991 Honda Accord LX failed EVAP test. The ASM Emission Test Results showed Test 25mph RPM 1933, %C02 MEAS 14.60, %02 MEAS 0.22, HC (PPM) MAX 61, GP 236, MEAS 19, CO (%) MAX 0.60, GP 2.10, MEAS 0.02, NO...


Things to consider or replace...

If you are getting a Check engine Light let me know, it will make things easier to diagnose.

Catalytic Converter
Oxygen Sensor
EGR Valve

May 17, 2010 | 1991 Honda Accord

1 Answer

Check engine light came on. computer found code P 1457? Honda accord 2000 2.3 litre Thanks


1457 is a leak in the charcoal canister or its plumbing system. my money says its in your plumbing. clogged/disconnected lines.

really though, the 1457, could be anything in your evap emmissions system. canister purge solenoid, 2 way bypass valve, fuel tank pressure sensor, canister vent shut valve, alot of rubber hoses, alot of hard plastic lines, evap canister, etc,etc,ect,etc.blah, blah,blah.

a good DIGITAL multimeter and vacuum pump will ease your pinpointing.

im not sure if haynes or helms carry the info on troubleshooting this problem, but, if they do, it'll be good as a reference map.

PS: my problem was with the two way valve.

Mar 23, 2010 | 1998 Honda Accord

2 Answers

Check engine light is on, code 1457, I replaced the gas cap...still won't go away?


This is a common problem with these and a few other Honda cars.

The code means "Evap Bypass Solenoid Valve Failure"

The solution is to replace a few parts dealing with the EVAP system.

You can call your local Honda dealer, as there is a TSB (technical service bulletin) on this problem, and it may be covered under warranty.

The TSB number to give them is 03-001.

Mar 19, 2010 | 1999 Honda Accord

1 Answer

Code P1457 for honda accord 2000


code p1457 is an evap leak code. a honda dealer can run a functions test on the system with the honda daig scan tool. but 90% of the time the probelm is the CVS valve. also known as canister vent shut valve. i've seen this a hundred times. its located under the rear of the car on the drivers side. its bolted to the evap canister with 2 (most likely rusted out) bolts.- hope this helps

Dec 12, 2009 | 1998 Honda Accord

1 Answer

Malfunction Indicator Light


The cost will depend on what else the shop deems necessary to complete the job after they retrieve all of the codes. Usually, the EVAP canister will be replaced and they will remove the EGR valve to clean the carbon out of the inlet /outlet tubes. Total generally 2-3 hours labor will be $250+-, and then add in the cost of the parts.

Feb 16, 2009 | 2001 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...