Question about Nissan Primera

1 Answer

Not turning over

Have relpaced starter, engaging but not turning over

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 22,219 Answers

On the starter motor their is a big large heavy cable that goes to the top large nut connection ,have you refitted this cable as i dont think you have so check it out first before you post any answer like i dont know what iam talking about ,or you connected it as i dont think you have and if you havent dont worry about i have made bigger boo bos than this trust me ,like fitting a clutch plate in the wrong way around or forgetting to tighten the wheel nuts and on more than one occasion ,mobile phones can be a blessing yes but a positive distraction as well

Posted on Feb 17, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Arctic cat 2000 300 4wd starter would not engage. I pulled starter tested on bench engages ok. where starter mounts in hole feels like gear in there turns free what does starter engage into help


did you test the battery on the cat low battery will cause engagement problems ---starter damaged or weak my be good under bench test with out a load --or miss aligned and wasnt meshing with flywheel

Nov 10, 2016 | Cars & Trucks

1 Answer

Wiring diagram 1999 buick century. Starter engages when battery cables are bolted to battery.


-the wires are not correctly re-installed for the starter.
- u may need wiring diagram
Did you take pictures before you took it apart, or did you tag wires before unconnecting them.

Mar 12, 2015 | 1999 Buick Century

1 Answer

Why does my 2005 dodge grande caravan turns over too slow to start?. Relpaced starter, had battery tested . tried boosting still no luck. please help


Sounds like you have a big draw on the battery that's not being caused by the starter. Try using a VOM to check the voltage at the starter during cracking. Also check for any voltage readings between the neg battery post and any ground point, the reading should be zero. Any voltage at all here indicates a complete circuit between the battery and ground where there should not be any as long as the ignition switch is off.

Jul 29, 2014 | 2005 Dodge Caravan

1 Answer

Starter motor turns but wont engage


A lot of times and on most vehicles, when the Starter turns over but will not engage, that means the Bendix inside the starter is not pushing the starter gear out to engage in starting your engine. Best solution would be to just simply replace the starter. Sometimes you can have the starter rebuilt, but in most cases the fasted and simplest way is to replace it. Hope this helps

Apr 07, 2014 | 2000 Daewoo Nubira

1 Answer

Wont start, clicking and all dash lights on. relpaced starter no go.


check the starter and ignition fuse. starter fuse is located in the fuse box in your engine bay, ignition fuse is located in the kick panel which is right under your steering wheel.

May 17, 2012 | 2006 Dodge Durango

2 Answers

Moter will not crank


check your starter,fuses

Apr 05, 2012 | Cars & Trucks

1 Answer

2003 dyna starter turns but wont engage, new battery fitted


Hi Anonymous, lift up rubber boot on positive cable to starter, unplug starter relay wire usually green, with a jumper wire connected to positive battery cable starter stud, touch blade connecter on starter where starter relay wire was removed. If starter engages and turns over engine then your starter relay is bad. If starter activates but does not engage then your starter drive/clutch is bad. Good luck

Jan 22, 2012 | Cars & Trucks

1 Answer

2005 mazda 3 clutch won't engage


relpace the clutch pressure plate and throwoout bearing. It all comes in a clutch kit.

Feb 18, 2009 | 2005 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...