Question about Cars & Trucks

1 Answer

How to replace the break bulb on victoria crown 2002 model

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,822 Answers

This is outlined in the owners manual. If you do niot have one download one HERE for free.

Posted on Feb 17, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 61 Answers

SOURCE: How to replace uppe ball joint in Ford Crown

First make an appointment for a front end alignment which will be required after replacing the ball joint. Securely support the vehicle under the lower control arm at the outer end, the end nearest the tire. The upper ball joint is attached to the upper control arm with 2 large nuts. Under the nuts are cams with hex heads for adjusting caster and camber. Mark the position of these cams in a way that will allow you to reinstall them somewhere near the same position. Next remove the outer end of the joint from the steering knuckle an then remove the 2 nuts and both cams from the control arm end. Reinstall and get that alignment asap !

Posted on Oct 05, 2009

c17hydro
  • 2984 Answers

SOURCE: Hi, How do I replace the tail light bulbs in my

Sedans

  1. Remove the screw(s) and wing nut retainers at the rear of the luggage compartment and push the trim away from the back of the light.
  2. Remove the wing nuts retaining the light assembly to the vehicle and the retaining nut from either side of the luggage compartment and pull the light body assembly from the vehicle.
  3. Turn the bulb socket(s) counterclockwise to the stop and remove the socket(s) from the light assembly. Remove the bulb(s) from the socket(s).
  4. Installation is the reverse of the removal procedure.
56c16fa.gif
Push the trim away from the back of the light—1992-98 Crown Victoria

f147c29.gif
The rear tailamp assembly is held by various fasteners

da5bd90.gif
Remove the wing nuts retaining the light assembly to the lower back panel—1992-98 Crown Victoria

e896b59.gif
Remove the nut retaining the light assembly from the side of the luggage compartment

2e1520f.gif
Pull the light assembly away from the vehicle—1992-98 Crown Victoria

Posted on Oct 12, 2009

Testimonial: "I was thinking I would get to the bulbs from inside the trunk. This info makes perfect sense. Thanks"

ZJLimited
  • 17970 Answers

SOURCE: i need drive belt diagram for a 2002 ford crown

2002 FORD CROWN VICTORIA - V8 4.6L 281ci CNG FI N 9
and
2002 FORD CROWN VICTORIA - V8 4.6L 281ci GAS FI N W

Belt Routing Diagram - Multiple Accessory

f091bd1.jpg


Hope helped (remember rated this).

Posted on May 26, 2010

ZJLimited
  • 17970 Answers

SOURCE: I need fuse panel diagrams for ford crown victoria

For check passenger compartment fuse panel, is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses.

Other details and descriptrions can find it in 2003 Ford Crown Victoria - Owners Manual (page 164 and next).

Hope helps (remember rated this).

Posted on Aug 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2005 Crown Victoria .....Brake lights just stopped working (upper light also) All other functions work fine(hazards,turn signals & running lights) Just replaced the brake switch & there st


change the light control module. it is located under the dash near your right knee on the drivers side. this is a common problem with crown vics.

Feb 11, 2013 | 2005 Ford Crown Victoria

1 Answer

How to replace the break bulb on victoria crown 2002


The information is in the owners manual, if you don't have the manual you can download for free from Ford at this site. Click the LINK

Feb 17, 2012 | Cars & Trucks

1 Answer

I need drive belt diagram for a 2002 ford crown victoria


2002 FORD CROWN VICTORIA - V8 4.6L 281ci CNG FI N 9
and
2002 FORD CROWN VICTORIA - V8 4.6L 281ci GAS FI N W

Belt Routing Diagram - Multiple Accessory

f091bd1.jpg


Hope helped (remember rated this).

May 26, 2010 | 2002 Ford Crown Victoria

1 Answer

Hi, How do I replace the tail light bulbs in my '97 Crown Victoria? Thanks


Sedans
  1. Remove the screw(s) and wing nut retainers at the rear of the luggage compartment and push the trim away from the back of the light.
  2. Remove the wing nuts retaining the light assembly to the vehicle and the retaining nut from either side of the luggage compartment and pull the light body assembly from the vehicle.
  3. Turn the bulb socket(s) counterclockwise to the stop and remove the socket(s) from the light assembly. Remove the bulb(s) from the socket(s).
  4. Installation is the reverse of the removal procedure.
56c16fa.gif
Push the trim away from the back of the light—1992-98 Crown Victoria

f147c29.gif
The rear tailamp assembly is held by various fasteners

da5bd90.gif
Remove the wing nuts retaining the light assembly to the lower back panel—1992-98 Crown Victoria

e896b59.gif
Remove the nut retaining the light assembly from the side of the luggage compartment

2e1520f.gif
Pull the light assembly away from the vehicle—1992-98 Crown Victoria

Oct 12, 2009 | 1997 Ford Crown Victoria

1 Answer

How do i change a rear turn signal bulb on a 1994 ford crown victoria?


in your trunk you should see 4-6 plastic screw fasteners unscrew these the whole assembly will come out take the bulb that bad out turn counter clockwise replace bulb reverse the process. (fyi)your screw fasteners may be behind the fabric that lines the trunk just pull this out of the way.

Sep 20, 2009 | 1994 Ford Crown Victoria

1 Answer

My air conditionier on my 2002 crown victoria is blowingout the w


Check the hoses underneath the cup holder area under the dash and make sure theres no obvious hoses disconnected. If they are ok, more than likely your selection switch is bad. You take off the plastic trim from around it starting from the passenger side of the car and remove the (4) 7mm bolts, carefully disconnect the colorful hoses and the wiring and replace the whole thing. I hope this helps

Jun 19, 2009 | 2002 Ford Crown Victoria

1 Answer

How do you install a 2002 crown victoria fuel pump


Hello;
You have to drop the fuel tank to get to the fuel pump. It does need to come all the way out for ease of replacement.
Thanks;
Rich
RPM Northwest

Apr 06, 2009 | 2002 Ford Crown Victoria

1 Answer

How do I replace bulbs where air condtion switches are ?


pull the AC/Heater control head out and u will find a tiny peanut shaped bulb at the back of the dash display, replace it.

Feb 12, 2009 | 1994 Ford Crown Victoria

1 Answer

'94 Ford Crown Vic Headlights


They are changed from within the engine compartment... at the rear of the headlight bazels... if it's the side on the battery you may have to remove it.... also don't touch the bulbs with your fingers as that shortens the life of them.

Robert

Jan 17, 2009 | 1994 Ford Crown Victoria

1 Answer

Odometer light out


This is fairly simple but is in a tight spot. You need to take the panel that has the rear defrost and truck button on it. Then you need to get an 8 mm and take out the casing that surrounds the insturment cluster (usually it is black), I believe you need to put the gear shift to the lowest gear to get enough room to pull the casing out. Then get a star tool to unscrew the cluster and pull it out toward you and then remove then remove the harnesses that plug into the back, be careful not to break the cable that is connected to the back of the cluster. Once all is complete on the back of the cluster there are black clips that have a socket on the inside which holds the bulbs. To pull these out you need twist these then they will release. At this point you can swap the bulbs with another bulb that you really dont need like the seatbelt light or just do the best thing and replace the bulb. Its been a while since I changed a bulb, so if I missed anything post it to inform others that may read.

Jan 05, 2009 | 2002 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...