Question about Cars & Trucks

1 Answer

TIMING BELT DIAGRAM FOR A VW TRANSPORTER VTE 2.5LTR

WE ARE HAVING TROUBLE FINDING THE CORRECT MARKS FOR THE TIMING BELT

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 17,970 Answers

Try in this link the Repair Manual: t4_car_rus.rar (size 72.39 MB) in order to check diagrams.

Hope helps.

Posted on Feb 17, 2012

  • ZJ Limited
    ZJ Limited Feb 17, 2012

    CHeck page 31 in the previous document.

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 97 isuzu rodeo timimg belt diagram 3.2 l

CONFIRM 6VD1 ENGINE

Posted on Dec 30, 2008

michigan man
  • 3533 Answers

SOURCE: need 2001 vw passat 4cyl. 1.8t. timing belt diagram

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

duane_wong
  • 6826 Answers

SOURCE: diagram for volkwagon transporter 1997

I found a 2.0L VW engine for a Cabrio. Not sure if this is the right one, but here goes:

REMOVAL & INSTALLATION

NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.

Gasoline Engines






Fig. 1: Adjusting the belt tension on a 2.0L 8 valve
91223g06.gif







Fig. 2: Remove the timing belt cover
91223p51.jpg







Fig. 3: Align the timing marks
91223p46.jpg







Fig. 4: Locate the tensioner
91223p47.jpg







Fig. 5: Loosen the tensioner bolt
91223p48.jpg







Fig. 6: Mark the belts direction of rotation
91223p52.jpg



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the
    No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch
    on the crankshaft pulley should align with the dot on the intermediate shaft
    sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.
    To install:

  6. Check the alignment of the timing marks. On 16 valve engines, the mark on
    the tooth should align with the mark on the rear belt cover.
  7. Install the new timing belt and tension the belt so it can be twisted 90°at
    the middle of it's longest section, between the camshaft and intermediate
    sprockets.
  8. Recheck the alignment of the timing marks and, if correct, turn the engine 2
    full revolutions to return to TDC of No. 1 piston. Recheck belt tension and
    timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45
    Nm).
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


Diesel Engines

Some special tools are required. A flat bar, VW tool no. 2065A, is used to
secure the camshaft in position. A pin, VW tool no. 2064, is used to fix the
pump position while the timing belt is removed. The camshaft and pump work
against spring pressure and will move out of position when the timing belt is
removed. It is not difficult to find substitutes but do not remove the timing
belt without these tools.
NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and
    rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the
    camshaft. The bar rests on the cylinder head to will hold the camshaft in
    position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in
    position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt. Slide the timing
    belt from the sprockets.
    To install:

  6. Install the new timing belt and adjust the tension so the belt can be
    twisted 45 degrees at a point between the camshaft and pump sprockets. Torque
    the tensioner nut to 33 ft. (45 Nm).
  7. Remove the holding tools.
  8. Turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck
    belt tension and timing mark alignment, readjust as required.
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


prev.gif next.gif

Posted on Oct 29, 2010

PowerOfLinds
  • 33 Answers

SOURCE: wat are the timing belt marks for a 2000 5 cyl

cam timing mark is on the back side of the cam view able through a small hole in the metal timing cover the crank shaft mark is on the transmission bell housing there is a opening that a -0- will line up to have an buddy turn the crank by hand and have a good light

Posted on Aug 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I Have a VW Golf 1,3 Shuttle And Need A Cam Belt Timing Diagram


Have a look on the link below - particularly in the images. You may be able to identify which engine is yours:

vw 1 3 timing marks Google Search

Apr 20, 2016 | Cars & Trucks

2 Answers

2005 vw jetta 2.0L 4cyl bbw engine code: need timing belt set up/marks


Here are a few diagrams to line up crank and cam, note there is a tool used with valve cover removed and slides into rear of cam to lock into place but as long as you hold it in the correct location with a wrench you will be okay and the crank you will need to put lower cover on and use lower pulley to line marks up and then double check the mark at the rear on the transmission, there are two diagrams i sent one is for automatic transmission and the other manual , i labeled them, the tensoiner, i assume you know how that must be done , if not let me know, the pointer must be in the right location. after timing belt is on you will spin crank two complete times and check the alignment marks if they are off try again. note you must not assume it is lined up spin crank to check.12_25_2012_7_59_29_pm.png12_25_2012_7_59_40_pm.png12_25_2012_7_59_50_pm.png12_25_2012_8_00_03_pm.png12_25_2012_8_00_16_pm.png

Dec 25, 2012 | Cars & Trucks

1 Answer

Where can i get a timing belt diagram for a 99 volkswagon beetle 1.8l turbo?


pretty good utube video for the procedure, type in 1999 vw timing belt

May 21, 2012 | Cars & Trucks

1 Answer

Wat are the timing belt marks for a 2000 5 cyl 2.5ltr petrol vw transporter


cam timing mark is on the back side of the cam view able through a small hole in the metal timing cover the crank shaft mark is on the transmission bell housing there is a opening that a -0- will line up to have an buddy turn the crank by hand and have a good light

Aug 08, 2011 | 2001 Volkswagen Eurovan

1 Answer

NEED TIMING MARK DIAGRAM FOR 1989 GOLF 1.6 DIESEL TO REPLACE TIMING BELT


The timing belt marks diagram for 1989 VW Golf 1.6 Diesel

tdisline_534.jpg
tdisline_535.jpg

May 15, 2011 | 1989 Volkswagen Golf

1 Answer

Diagram for volkwagon transporter 1997 2 litre 4 cylinder timing belt replacement


I found a 2.0L VW engine for a Cabrio. Not sure if this is the right one, but here goes:

REMOVAL & INSTALLATION

NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.

Gasoline Engines






Fig. 1: Adjusting the belt tension on a 2.0L 8 valve
91223g06.gif







Fig. 2: Remove the timing belt cover
91223p51.jpg







Fig. 3: Align the timing marks
91223p46.jpg







Fig. 4: Locate the tensioner
91223p47.jpg







Fig. 5: Loosen the tensioner bolt
91223p48.jpg







Fig. 6: Mark the belts direction of rotation
91223p52.jpg



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the
    No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch
    on the crankshaft pulley should align with the dot on the intermediate shaft
    sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.
    To install:

  6. Check the alignment of the timing marks. On 16 valve engines, the mark on
    the tooth should align with the mark on the rear belt cover.
  7. Install the new timing belt and tension the belt so it can be twisted 90°at
    the middle of it's longest section, between the camshaft and intermediate
    sprockets.
  8. Recheck the alignment of the timing marks and, if correct, turn the engine 2
    full revolutions to return to TDC of No. 1 piston. Recheck belt tension and
    timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45
    Nm).
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


Diesel Engines

Some special tools are required. A flat bar, VW tool no. 2065A, is used to
secure the camshaft in position. A pin, VW tool no. 2064, is used to fix the
pump position while the timing belt is removed. The camshaft and pump work
against spring pressure and will move out of position when the timing belt is
removed. It is not difficult to find substitutes but do not remove the timing
belt without these tools.
NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and
    rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the
    camshaft. The bar rests on the cylinder head to will hold the camshaft in
    position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in
    position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt. Slide the timing
    belt from the sprockets.
    To install:

  6. Install the new timing belt and adjust the tension so the belt can be
    twisted 45 degrees at a point between the camshaft and pump sprockets. Torque
    the tensioner nut to 33 ft. (45 Nm).
  7. Remove the holding tools.
  8. Turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck
    belt tension and timing mark alignment, readjust as required.
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


prev.gif next.gif

Oct 29, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

I need to find a diagram for a timing belt for a 1995 isuzu rodeo. I purchased the belt but am having trouble getting it placed on correctly.


We are talking about the Timing Belt and not the Drive/Surpentine Belt?

For the Timing Belt: CLICK on the following Link. It has all the Diagrams you will need for the Timing Belt.
http://www.2carpros.com/car_repair_information/year/1983/make/isuzu/model/pickup/1983_isuzu_pickup_timing_belt_diagram_marks.htm

For the Drive/Surpentine Belt: CLICK on the following Link. It has all the Diagrams you will need for the Drive/Surpentine Belt.
http://www.2carpros.com/car_repair_information/year/1995/make/isuzu/model/rodeo/1995_isuzu_rodeo_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Feb 27, 2010 | 1995 Isuzu Rodeo

2 Answers

Retiming of vw transporter diesel pump


hi there if you remove the cam pully wich drives the diesel pump you will see a key way in the end of the cam turn the engine untill the key way is flat ( i use a streight edge in the keyway and turn until it is level with the top of the cylinder head ROCKER COVER REMOVED once this is aligned up there is a mark o the back of the diesel pump pully thiss aligns up with a groove between two castings on the side of the pump at the front of the engine once all these are aligned up you can put on the belt ( it may ot start right away this wil be due to needing to bleed up the fuel ONLY IF PUMP BEEN REMOVED and bleeding up the fuel can be a right pain. hope thos helps ben

Jul 07, 2009 | 1993 Volkswagen Eurovan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...