Question about Lexus ES 300

Open Question

Where is the shift solenoid transmission on mazda 96 b4000

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 95 mazda b4000 slave cylinder bleeder valve location

the nipple sticks out side the bell housing on the left side just above your hydralic line for your clutch,auto zones web has a complete diagraham and steps for bleeding

Posted on May 09, 2009

  • 105 Answers

SOURCE: 96 plymouth grand voyager, transmission slipping,not shifting

trans is shot very common problem you can rebuid it but thats not cheap finding a used one will be very difficult as 96 is a one year only model and there where 2 within that year depending on the buid date of the van

Posted on Jun 04, 2009

roniecon
  • 6826 Answers

SOURCE: emergency brake sticking.....i think. Mazda B4000 pickup

Are you sure it is the emergency brakes?Or is it a caliper stuck,because it is bad,or the caliper brake hose is stopped up?Jack the wheels up,one at a time,and try to see if they will turn by hand.This will tell you if it is front,or rear.If it is the emergency brake,then the cable from the front,to the bake,is most likely the problem,it is rusted ,and frayed,and stuck,you will have to disconnect it at the rear,from the brakes.If this helps,let us know,If it is the calipers,in the front,the wheels will not turn by hand.Brake loose the caliper bleed screw,and if the caliper turns the wheel loose,then the brake hose is bad,if it does not ,then the caliper is bad on that wheel.

Posted on Dec 05, 2009

  • 538 Answers

SOURCE: 96 ford tuarus that has AX4N transmission wont

You may want to change the vehicle speed sensor first. Is your speedometer working? The shift solenoids are inside the side cover of the transmission and it's quite a job to get that cover off, you practically have to take the trans out of the car. Are you getting a "check engine" light there may be a code in the computer that will tell you what is going on. If one of those solenoids fail it should trigger a "check engine" light, the solenoids are usually pretty trouble free as a rule. I'm not sure on that transmission, but I think there are two shift solenoids, but there is also a "torque converter clutch solenoid". Also, if you can get it to a trany shop they can put a scan tool on your car and tell you exactly what's happening. Have you tried manually shifting the car? Pull it down into 1 then manually shift it up, see if it will shift that way.

Posted on Mar 20, 2010

Testimonial: "Thank you, that gives me a clear direction to start troubleshooting "

  • 158 Answers

SOURCE: transmission control solenoid location for 96 ford f150

whether it is the smaller (4R70w) or the bigger (E4OD), the solenoids are under the pan. The E4OD solenoids are in one big block where the other trans has them seperated

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Mazda B4000 2-whl drv: "overdrive off" light is flashing. From standing stop, will not shift up unless take foot off accelerator then press to resume (manual shift w/accelerator). Error code indicates...


That is most likely inside the transmission. IF the fluid level is ok and all the wires to the transmission are ok, it is time for an overhaul

Oct 21, 2013 | Cars & Trucks

2 Answers

I have a 96 Mazda B4000 4wd pickup I need door lock cylinder one of mine is broke cant find any know where I could possibly find them. Thanks


I would get 2 the same keyed alike from a salvage yard

From there a lock smith maybe able to reprogram if nec

Jan 21, 2013 | 1996 Mazda Pickup

1 Answer

Can shift solenoid on 2004 Mazda MPV be replaced individually


yes you can have just the bad shift solenoids replaced . you do not need to replace the transmission

Dec 28, 2012 | 2004 Mazda MPV

1 Answer

93 mazda mx3 wont shift in high gear


clutch plate worn causing slipping no increase in speed or transmission fluid low or transmission fluid old contaminated, transmission need fluid and filter change.could have fault in the kick down solenoid or over drive cancel solenoid.have transmission shop code scan look for faulty shift solenoids or speed sensor fault code,lock up solenoid got a lot of parts any one of them cause no over drive.

Sep 23, 2012 | Mazda MX-3 Cars & Trucks

1 Answer

Po756 code and blincking od light 96 ford explore


P0756 FORD - Shift Solenoid 2 Performancexicon.jpghttp://engine-codes.com/p0756_ford.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 2 valve
- Shift solenoid 2 valve harness or connectors
- Shift solenoid 2 valve circuit is open or shorted
help.png Help with thisTech notes When the a transmission solenoid is stuck off, in most cases the problem is not the electrical part of the solenoid; the problem is foreign material obstructing the mechanical function of the solenoid or the flow of the fluid through the transmission valve body. If the transmission fluid is very dirty, it is recommend changing the transmission fluid and if possible removing the transmission pan for further diagnosis. Excessive debris or metal particles on the transmission pan could be an indication that there is a transmission mechanical failure and that the transmission will need to be rebuilt or replaced.

Jul 06, 2012 | 1996 Ford Explorer

1 Answer

How do i fix a po757


Hi there:

DTC P0757 MAZDA - Shift Solenoid B Stuck On

The P0757 code is detected when the ECM has detected a mechanical fault with the solenoid energized, valve stuck on.

Shift solenoid valve B is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position. When the a transmission solenoid is stuck on, in most cases the problem is not the electrical part of the solenoid; the problem is foreign material obstructing the mechanical function of the solenoid or the flow of the fluid through the transmission valve body. If the transmission fluid is very dirty, it is recommend changing the transmission fluid and if possible removing the transmission pan for further diagnosis. Excessive debris or metal particles on the transmission pan could be an indication that there is a transmission mechanical failure and that the transmission will need to be rebuilt or replaced.


Possible causes:

- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid B valve
- Shift solenoid B valve harness or connectors
- Shift solenoid B valve circuit is open or shorted

I suggest ask your dealer about the folow TSB...
7_3_2012_6_39_50_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 03, 2012 | 2002 Mazda MPV

1 Answer

96 mazda b4000 vibration when driving and braking


There are a few possible issue's that could be causing the vibration..You will have to narrow it down...At what speeds does this happen at??Check your motor mounts and transmission mounts...

Oct 08, 2011 | Mazda B4000 Cars & Trucks

1 Answer

Just scanned my 1999 300m. It went into safe mode while me wife was driving it home- 2nd gear only. It had a code P1714 and P0700 come up on the scanner. I can't find anything about the P1714.


Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
That code is low battery voltage on a chrysler

Jun 12, 2010 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...