Question about 2007 Ford Focus 2.0

Open Question

Headlight adjustment screw don`t adjust my headlight

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: can't adjust 2004 Ford Expedition headlight

I had a similar problem on my 04 expedition. I just bought it and the headlights were aiming too far down. A rather larger gap was noticeable between the headlight and the hood. The so called adjustment bolt did nothing. I removed the headlights and found 2 issues. On the adjustment bolt there is a washer. Make sure when you re-install the headlight the washer sets on top of the plastic slot and is visible when looking down behind the headlight. Without the washer being in the correct location it will not tighten the headlight in place.
Second I found the adjustment bolt adjusted nothing. It merely tightened the headlight in place. What I had to do was to loosen this bolt and physically move the headlight into place and the re-tighten the bolt. Hence the slot is the adjustment. Turning the bolt CW or CCW did not move the headlight.
I tried several things trying to figure why the lights would not move until I realized I could move the light with my hands and tightened them in place using the adjustment bolt.

This may not be your issue but I found the owners manual instructions to be useless.

Posted on Jan 02, 2009

  • 1986 Answers

SOURCE: 1998 Ford Mustang Headlight Adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: Headlight adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: Adjust (aim) headlights on a 1990 Ford Taurus

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

  • 183 Answers

SOURCE: were do you get the special tool to adjust

any outo parts store should sell them..also sears or kmarts

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust the headlights on an 86 jeep Comanche


How to adjust the headlights on an 86 jeep Comanche - Fixya

www.fixya.com/cars/t26003692-adjust_headlights_86_jeep_comanche
9 mins ago - Do you mean Aftermarket or Factory Harness ... it sounds more like a faulty headlight switch assembly ... Buy a new one at a parts store, install it.

Headlamp Adjusting Screw - Sold Individually - 55054621

www.morris4x4center.com/headlamp-adjusting-screw-55054621.html

Rating: 5 - ‎5 votes
1984-2001 Jeep XJ Cherokee; 1986-1992 Jeep MJ Comanche. Description: This is aHeadlamp Adjusting Screw. This allows you to aim your headlights ...

Headlight adjustment - Jeep Cherokee Forum xjTalk - A Jeep podcast!

xjtalkshow.com/showthread.php?t=13045
Jan 7, 2013 - Headlight adjustment OEM/Factory. ... the JEEP TALK SHOW! It's aJEEP podcast! iTunes, Stitcher, TuneIn or... http://jeeptalkshow.com ...

Adjusting headlights - JeepsUnlimited


Dec 12, 2015 | Jeep Cars & Trucks

1 Answer

Adjusting headlights


No. There are two adjustment screws for each headlight assembly. One adjusts for up and down, the other is for side to side. New adjustment screws can be purchased at a parts store.

Dec 24, 2013 | Cars & Trucks

1 Answer

Illistration on how to change a headlight bulb


HEADLIGHT REMOVAL AND INSTALLATION
SEALED BEAM HEADLIGHTS REMOVAL 1 When replacing the headlight,do not turn the spring-loaded adjusting screws or the headlight aim will be changed 2. Remove the cover over the headlight this vehicle has five screws securing the cover other models may have four or six screws. 3. Remove the four screws which secure the retaining ring around the headlight support the headlight as this is done. 4. Pull the light away, unplug the connector and remove it from the vehicle. INSTALLATION 5. Position the new unit close enough to connect the wires. Make sure the numbers molded into the lens are at the top. 6. Install the retaining ring and mounting screws. 7. Install the plastic cover to the headlights with the screws you took off and check for proper operation. If the adjusting screws (spring - loaded adjusting screws) were not turned, the headlight should not require adjustment.

Jan 17, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Which way do the headlight vertical adjustments turn to raise the beam?


Turn on your headlights and locate the two adjustment holes that have the adjustment screws inside them on the sides of each headlight. The top hole has the vertical adjustment screw and the bottom hole has the horizontal adjustment screw. Turn the vertical screw clockwise to raise the beam and counterclockwise to lower; turn the horizontal screw clockwise to move the beam right and counterclockwise to move the beam left.

click this link for more help:--- http://technoanswers.blogspot.com/2011/05/how-to-adjust-headlight-beam-on.html --------- This should help.thanks.Helpmech.

May 29, 2011 | 2002 Chevrolet Corvette

1 Answer

How I adjust headlights on a 1999 grand am?


  • Determine the type of headlights you have on your car. You can only adjust composite headlights if they bolt to adjuster plates. For dual headlights, look on the headlights for four adjustment screws per side. Sealed beam units have interior adjustment screws under the hood.
  • 4 Locate your adjustment screws. On sealed beam units, you may need to remove the trim screws and pull the trim off to reveal the Torx screws.
  • 5 Begin with you headlights turned on to the low beam. Use a Torx screwdriver for sealed beam units and Phillips screwdrivers for other types of headlights.



  • Dec 09, 2010 | 1999 Pontiac Grand Am GT

    2 Answers

    How do you adjust headlights??


    The best way to do it is to park your car in front on a garage door, a building or put a piece of plywood in front. Whichever you use, park you car at least 10 feet away; so you can tell if you are going up, down or in the middle when adjusting.
    1. Remove the four screws that secure the headlight trim bezel to the grille.
    2. Remove the headlight trim bezel.
    3. Turn the headlight high beams on.
    4. Adjust the headlights. Use the adjustment screws located along the outboard side and the inboard lower corner of the headlight bucket. Adjust the headlights until the beams are centered directly on the wall.
    5. Replace the headlight trim bezel.

    Nov 15, 2010 | 1995 Ford Escort

    1 Answer

    How do i adjust my headlights?


    • Always adjust lights with optical headlight aimer VAS 5107, using detailed aiming procedure and specifications
    • Low and high beams are adjusted simultaneously.
    98971520



    Left headlight (adjustment screws for right headlight are mirror image):
    1 - Lateral adjustment 2 - Height adjustment
    • Access adjustment screws through hole in lock carrier (Phillips head or socket head).
    • Turn the adjusting screws for lateral adjustment -1- and height adjustment -2- until the correct setting is achieved.
    NOTE: Where equipped, ensure equal movement/function of headlights during automatic headlight range adjustment.

    Oct 19, 2010 | 2001 Volkswagen Passat

    2 Answers

    Headlight adjustment screws


    They will probably be inset adjacent to the headlight. You'll find a horizontal and a vertical adjusting screw, with small springs behind them. Some cars come equipped with a small level (like a carpenter's level) attached to the top of the headlight under the hood to help you get the correct adjustment.

    Nov 12, 2009 | 1992 Dodge Dakota

    1 Answer

    Headlight adjustment


    Most headlights have two adjustment screws. On on top and one on the side. These will be phillips head screws. Usually you would need to turn screw to the right to adjust right or up. Left for left or down.

    May 11, 2009 | 2007 Nissan Murano SE

    2 Answers

    Adjusting headlights on a 2005 ford freestar


    hello wwhampton,

    open the hood, take a close look at your headlights, if it is a headlight assembly, there are two screws with big plastic heads on the back of the assembly, these are the adjusting screws. one for horizontal adjustment and the other one is for vertical adjustment.

    if the headlight is a round or square ordinary bulb, the adjusting screws are located near the bulb itself, these are philips screws. one on the top and one on the side.

    a suggestion; when adjusting headlights, face the car to a wall about 5 ft away and adjust the headlight.

    tnx 4 using fixya.

    drcool

    Sep 20, 2008 | 2005 Ford Freestar

    Not finding what you are looking for?
    2007 Ford Focus 2.0 Logo

    Related Topics:

    24 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...