Question about Cars & Trucks

Open Question

Replace a v-belt 1994 e320 3.2L

Need to replace v-belt 1994 e320 3.2L eng

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: air conditioner belt 3.5 eng

A/C Belt To Remove:
NOTE: The A/C drive belt self tensioner is NOT a dynamic tensioner. After adjustment the tensioner bracket bolts are tightened. The torsion spring is no longer responsible for tensioning the A/C belt. The torsion spring is only used for initial belt tensioning.

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove alternator/power steering belt to gain access to A/C belt:
  3. Loosen, do not remove tensioner locking bolt and pivot bolt.
  4. Insert 1/2" drive breaker bar into square opening on belt tensioner.
  5. Rotate tensioner counterclockwise until belt can be removed from pulleys.
  6. Slowly rotate tensioner clockwise to relieve spring load. NOTE: Clean all foreign debris from belt pulley grooves. The belt pulleys must be free of oil, grease, and coolants before installing the drive belt.
    NOTE: Belt replacement under any or all of the following conditions is required:
    • Excessive wear
    • Frayed cords
    • Severe glazing
  7. NOTE: Poly-V Belt system may develop minor cracks across the ribbed side (due to reverse bending). These minor cracks are considered normal and acceptable. Parallel cracks are not
    NOTE: Do not use any type of belt dressing or restorer on Poly-V Belts.

Posted on Jun 28, 2009

  • 334 Answers

SOURCE: serpentine belt diagram for 2003

Hello avatar15.jpgeleblanc1234,

Below is a diagram of the belt routing.


8_21_2011_4_43_36_pm.png

I hope this helps.

Regards,

Jerry

Posted on Aug 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do i connect the eng temmp control gauge on the eng of a 1994 2.5L block


double posted, back up one page, i posted the fsm pages.
the full fsm for 93 is online, free.
maybe correct.
if not, use alldata.com log in read.

Jan 24, 2015 | 1994 Jeep Grand Cherokee

2 Answers

Enging cranks but no start, has spark and gas


Your engine is flooded with fuel. Check your throttle body if it's a fuel injected engine. Clean it. Remove spark plug, let it dry or replace with new ones.Try flooring your acc pedal and start. If it starts, you need to get the carb serviced. For fuel injected, you need to service/ repair/replace your throttle body, fuel injectors, idle air control valves and EGR.

Jun 13, 2014 | 1994 Toyota Camry

1 Answer

Timing chain replacement 1994 land cruiser 4.5 eng


Best not be an azzclown and get your T Belt changed and it may be less than 1500 dollars but good luck with that,ya get what you pay for!

Feb 07, 2012 | 1994 Toyota Land Cruiser

1 Answer

Where are the timing marks on a 1994 dodge grand caravan 3.3 eng and the sedrpentine belt diagram?


This vehicle is not equipped with timing marks. However spark advance can be monitored using a DRBII or equivalent scan tool. Here is a pic of drive belt with A/C....

michael_cass_662.jpg

Sep 24, 2011 | Dodge Caravan Cars & Trucks

1 Answer

I have a 1994 chev cavalier convertable i would like to know where to find the engine number thank you dave


it should be on the front of the eng. just right of the timing belt cover,And u might be able to go to the chevy site and put in ur VIN#

Apr 02, 2011 | 1994 Chevrolet Cavalier

1 Answer

Replaced pressure line on power steering. now battery light comes on. belt squeeled when started, then stopped. Did power steering fluid get on belt and caused it to squeal and slip?


If you have a 4cyl then the belts for PS and alternator are separate. Taking a peek under the hood when the engine is running should give you a better idea if a belt is slipping, broken, etc. A common source of squealing is an alternator belt that is too loose and slips under heavy load charging the battery after startup. It's possible that some sort of problem happened due to replacing alternator belt but that belt slipping should be pretty easy to see. (again ... speaking of the 4cyl / 22RE enging)

Oct 08, 2010 | 1994 Toyota Pickup

3 Answers

Colant lose at right side of 3800 eng. 1994 park ave visable about half way down side below pully.


Most likely water pump. Might be broken plastic heater hose elbow, lower intake to belt tensioner. They tend to become brittle with age.

Sep 27, 2009 | 1994 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...