Question about 1997 Lincoln Continental

Open Question

1998 lincoln continental rear hub torque specs.

Torque specs.on rear axel hub on front wheel drive car

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: how to change the front wheel hub for 2000 LINCOLN LS

hi you will have to remove the wheel,grease cap from the hub remove the brake caliper and move aside (do not seporate rubber line). (discard caliper bolts can not be reused) remove rotor,wheel hub retainer nut (and discard nut can not be reused) in order to remove the hub

install

hub and new nut and tighten new nut to 189-254 ft.lbs
rotor new grease cap seal
brake caliper with 2 new bolts tighten to125-170 ft.lbs
wheel tighten to85-104 ft.lbs
pump the brake pedal befor moving car

Posted on Feb 06, 2009

frankgant
  • 250 Answers

SOURCE: Diagram for 1998 lincoln continental

There should be a diagram of the route printed on the fan shroud or somewhere else under the hood of the vehicle.

Posted on Jul 09, 2008

warlock61
  • 659 Answers

SOURCE: replacing front wheel bearings

fronts are bearing ahd hub assy remove the black center cover remove the hub nut and the hub should slide off. the caliper and rotor also have to be removed

Posted on Apr 21, 2009

jaysonemanme
  • 500 Answers

SOURCE: how to replace my 1994 lincoln towncar rear axel seal

you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

Posted on May 25, 2009

  • 1986 Answers

SOURCE: replace rear brake light bulb 1998 lincoln continental

pop the trunk and right behind where the lights are pull the carpet down and their will be of the following depending on the trim.

You will either see the light sockets themselves that you can twist and pull to change the bulb, or you will see the plastic nuts/screws that you can remove to remove the entire assembly in order to access the bulbs.

If it's your 3rd brake light, the screws to access the housing are located in the upper part of the trunk

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy malibu torque hub bearing front axel


about 80 lbs is sufficient ,if the wheel still can moved top to bottom then then renew the bearing ,and check the ball joints on the lower track control arm

Jan 17, 2015 | 2000 Chevrolet Malibu

1 Answer

What are the torque specs for a front axle bearing/hub?


Not sure about your model, but in general they are usually around 180 ft./lbs.

Aug 01, 2014 | 2003 Chevrolet Silverado 1500

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Torque spec


150 ft/lbs.; I work at a Chrysler dealership

Nov 29, 2009 | 1998 Dodge Grand Caravan

1 Answer

Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.


Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Jul 12, 2009 | 2000 Buick LeSabre

2 Answers

Transmission


No two entirely different transmissions.
Town Car is rear wheel drive and Continental is front wheel drive

Mar 13, 2009 | 1999 Lincoln Continental

Not finding what you are looking for?
1997 Lincoln Continental Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...