Question about Hyundai Accent

Open Question

Where is the pcm located in 2000 hyundai accent

Communication establish can't pass inspection

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maklean
  • 1665 Answers

SOURCE: 2000 Hyundai Accent

00-30-001 2000 ACCENT DMTL DIAGNOSIS: DTC CODES P1401, P1402 AND P1403

p1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected

Posted on Jun 04, 2008

  • 566 Answers

SOURCE: hyundai accent, location of fuel cut off

hi from uk location of fuel safety shut off valve/switch on uk r/h drive accents is on the engine bay bulkhead in front of drivers side it is a square box with red rubber top press button may be on opposite side on l/h drives ? if activated? just press button till click ? to reset these normally only cut off on impact ? to stop elec fuel pump continuing delivering if involved in an R.T.A fire prevention

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: DLC communications with OBD not possible

OBD II connector troubleshooting 101

I had the same problem with my 2000 Elantra. the OBD II connector pins get squished and won't make cantact with the scan tool, therefore no connection. the solution is to bend the pins back so they will connect to the scan tool.


FIRST! check your lighter and radio fuses (which you have already done). If possible, make sure your scan tool is working properly, try it on another car. If it is functioning properly, remove the 2 screws holding the obd II connector to the dash. Look for obvious signs of corrosion, damage, or stuff that shouln't be in the connector (rocks, gum, etc.) clean the connector with a good electronics cleaner (I use the CRC stuff), you can usually find it at you local parts store, radio shack, or even wal mart. hose down the inside of the connector thouroughly and allow time to dry.

check for voltage between 4 (gnd) & 16 (+vcc) then 5(gnd) and 16(+vcc) with the ignition on the voltage should be between 12v-16v (these pins may be different on other cars, look for an OBD II connector pinout diagram if your car is different). If this voltage is not present at either pin, the problem is not the connector. check your fuses and wiring. if this voltage is present at both pins continue.

Here's what I did. with the connector free from the dash, you can see the back of the connector where the wires enter the connector. on either side of the connector there may be a white clip. pop both of them off. you should be able to push a small screwdriver or pick in that space to pull the pins back out towards the outside of the connector. do one at a time so you can tell if the pin has moved back out into position. do this for all of the pins. Try to connect. if still no luck try again to push out the pins and reconnect.

If your connection is restored, replace the clips, screw it back into the dash. Return your car to the lousy DMV where they will proceed to tell you something else is wrong which they neglected to tell you on your first 10 visits!! :-)

Stuff thats good to know:
some auto parts stores will connect their OBD II scan tool to you car for free. auto zone is one place
some times the computer will need to reset to restore a connection to the scan tool. to do this simply cycle the ignition off (wait a few seconds) then on again.
online auction places are a excellent resource for USB to OBD II connectors to connect your laptop to your car. there is lots of OBD II diagnostic freeware out there to go with your newly purchased connector.

Good Luck

Chris
-CL Systems

Posted on Feb 06, 2009

  • 134 Answers

SOURCE: free owners manual for hyundai accent 2000

Go to hyundaiusa.com and then click on OWNERS on their menu bar. Then create a new account for your specific Hyundai vehicle year and model. Once you successfully log into your account, under the My Vehicle page you should see an underlined link labeled "Owners Manual". Clicking on this link, you will then be able to download a complete PDF version of the original owners manual.

Posted on Apr 27, 2009

  • 1201 Answers

SOURCE: i need to locate fuel filter on 2002 hyundai accent

Remove rear seat, there is an acess panel, remove panel, filter is under that. Before removing filter, release fuel pressure by loosening gas cap.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 hyundai accent emissions need to be cleaner


change the catalytic convertor,, any mechanic can do this for you.

Dec 30, 2012 | 2000 Hyundai Accent

1 Answer

Leak on athe flex pipe of exhaust


Yes, you can use silicone sealant on the cone of the car speaker.


---------------------------------------
Godiag M8 Wireless Auto Scanner

Dec 06, 2012 | Hyundai Cars & Trucks

2 Answers

Why didn't hyundai build a 2000 accent gt


http://en.wikipedia.org/wiki/Hyundai_Accent Here's the history,it says they were redesigned in 2000,click on link to read.

Sep 03, 2012 | 2000 Hyundai Accent

1 Answer

I'm getting code p0113 and I replaced the maf sensore and still getting the same code. can some one help? Hyundai accent 2001. thank you very much.


  • Did you clear that code AFTER performing the repay. If you did not clear the code then it will remain. If you did then you have a wirning issue or a connector issue or you bought a bad sensor or the PCM could be bad.. Make a full inspection of the wiring and conector all the way from the sensor to the PCM. If you do all of this and the code returns then at this point a full scanner will have to be hooked up and some diagnostics performed to inspect things. Sometimes it comes down to this. if it was never necessary, $10,000 scanners would not be necessary. Good luck to you.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards,Tony

Oct 12, 2011 | 2001 Hyundai Accent

1 Answer

Does anyone have a suggestion on resetting a 2004 hyundai accent so the car can pass smog. it needs two more monitors to run evap andcatlytic converter.


when you get to the insp. station unhook the posative battery cable and ground the wire
this (WILL) reset the computer so you wont see any codes and it shood pass inspection
with no proublam...

i hope this helps you (BOB) !!!

Sep 23, 2011 | Hyundai Motor 2004 Accent

1 Answer

What fuel filter do i need for my 2000 accent?


Welcome to FIxYa.com


Part # FF884 at Auto Zone For the price of (in my area) is $14.99

Location of Filter is: On top of the fuel tank beside the fuel pump. Accessible removing the rear seat and detaching the inspection panel of the fuel pump

91c7b4c.png



Regards, Lee Davidian


A Four Thumbs up ^^^^ is appreciated for answering your question.

Thank you, Lee Davidian

Oct 19, 2010 | 2000 Hyundai Accent

1 Answer

I am trying to locate the fuel filter in my 2000 hyundai accent. please help????


Under the rear seat there is an inspection plate housing the fuel pump. Lift the plate and the filter is next to the pump.

Thank you for using fixya and be safe

Oct 10, 2010 | 2000 Hyundai Accent

2 Answers

Where is the fuel filter located on a 2000 hyundai accent


The fuel filter for a 2000 hyundai Accent is under the back seat. You just lift the seat with the tabs and under the seat is a little door. you just lift it up and the fuel filter is right there.

Aug 03, 2009 | 2000 Hyundai Accent

1 Answer

Just bought 2000 Hyundai Accent yesterday


This link below may help on tune up procedure. Click on next page to step 7-8
http://www.2carpros.com/how_to/how_to_tune_up.htm

Jun 20, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...