Question about Toyota Cars & Trucks

Open Question

Where is placed automatic choke in 4AFE engins of toyota corolla

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 totota corolla reset engine light

You need to disconnect the negitive lead to your battery for at least 5 minutes. This allows the system to reset.

Posted on Apr 28, 2009

gregstobbe
  • 56 Answers

SOURCE: I want to know electrical diagram toyota corolla 1995 1.6 4AFE

all the wiring diagrams can be found here for free.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006f4db

hope you get it solved.

Ps dont forget to rate the solution. Thanks

Posted on Dec 28, 2008

  • 383 Answers

SOURCE: need timing belt mark diagram for 95 corolla 4afe

malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

Posted on May 06, 2009

  • 64 Answers

SOURCE: Engine over revving at idle

looks like yor air valve is not working properly.check the water imput (could be clogged). also,did you removed your termostat? if so,put it back and solve the problem.

Posted on May 02, 2010

  • 14 Answers

SOURCE: my 1999 toyota corolla 1.6 4afe engine cooling fan

sensor broken and its in "fail safe mode" which is it assumes that the engine is too hot if it does not know. check wires then replace sensor. did you take the motor out recently?

Posted on Jun 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Como poner a tiempo un geo primz 1.6


wow 1/2 spanish and english , a first. here.
wow 2, why not post the JOB, what JOB are you doing
the FSM books are indexed by JOB. so.....
so the prizm is a toyota corolla and uses a corolla engine.
that link above shows the toyota nation site, and all you ask is there
in English, are you asking for spanish translations of our books and forums?.
and still did not answer , cam or distributor timing? WHAT? job>
so 4AFE engine, you have.
alldata.com covers that for both corolla and prizm
as does
ok so ill pretend you said, CAM TIMING (Synchronization)
here ill type for you on toy nation
"4AFE cam timing' In the search box. for YOUR engine.

http://www.toyotanation.com/forum/gtsearch.php?cx=partner-pub-7865546952023728%3Algfaynpqci4&cof=FORID%3A11&ie=UTF-8&q=4AFE++cam+timing&sa=Search&siteurl=www.toyotanation.com%2F&ref=www.google.com%2Furl%3Fsa%3Dt%26rct%3Dj%26q%3D%26esrc%3Ds%26source%3Dweb%26cd%3D1%26sqi%3D2%26ved%3D0CB0QFjAA%26url%3Dhttp%253A%252F%252Fwww.toyotanation.com%252F%26ei%3DWo_GU_2nMcKcyASF4oK4CA%26usg%3DAFQjCNH6224mtR5X0XCGUiHd866fCQE_Fw%26bvm%3Dbv.71126742%2Cd.aWw&ss=8852j16351314j20

over 10 pages of hits.

is this hard? searching, for such a common engine?

Feb 18, 2015 | 1995 Geo Prizm

1 Answer

Toyota corolla 4afe engine rpm when idle too high


My corolla 4a-fe engine idle high and after driving for 30 minutes it cutoff engine and I must wait it to cool down. When I stop I need to rev it higher because it wants to switch off

Nov 21, 2012 | Cars & Trucks

1 Answer

What is the sparkplug gap for a toyota 16i GLE toyota 1994?


Make: TOYOTA
Model: COROLLA
Year: 1994
Engine: L4 - 1.6L - FI - 4AFE - GAS

Part Number RC12YC
OE GAP: .032" w/DOHC (Original Equipment Manufacturer and/or Original Equipment Equivalent)

Good luck.

May 09, 2011 | 1994 Toyota Corolla

2 Answers

1990 4AFE head torque & sequence


toyota carina e 1.6i 4afe 16v engine cam tightening torques and sequence pls, thank u

Apr 21, 2011 | 1990 Toyota Corolla

1 Answer

I need the torque settings for a Toyota Corolla 1995 model 4afe engine TORQUE SETTINGS FOR THE CYLINDER HEAD? PLEASE PLEASE HELP


cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Feb 22, 2011 | 1995 Toyota Corolla

1 Answer

1990 toyota corolla crankshaft and camshaft sensors where are they located


hello.i had about 10 of these corollas from 1988 thru 1992.i also performed all of the mechanical work on them.these cars with the 1.6 4afe engine,to my knowledge,DO NOT come equipped with either a crank or camshaft sensor.i hope this information helps you.take care and good luck, manny

Jul 11, 2010 | 1990 Toyota Corolla

1 Answer

My 1999 toyota corolla 1.6 4afe engine cooling fan on all the time even when cold


sensor broken and its in "fail safe mode" which is it assumes that the engine is too hot if it does not know. check wires then replace sensor. did you take the motor out recently?

Jun 21, 2010 | 2000 Toyota Corolla

1 Answer

Where can i find the car owner's manual of toyota gli? model 1994 4afe engine


There Are several Websites that sell Old Factory Manuals .Here is one that might be what you are looking for.
http://search.factoryautomanuals.com/search?keywords=+1994+Corolla

Nov 06, 2009 | 1994 Toyota Corolla

2 Answers

TOYOTA COROLLA 1995 1.6 4A-FE


Hello!
I want to know electrical diagram toyota corolla 1995 1.6 4AFE
Thanhs1

Jun 19, 2008 | 1995 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...