Question about 2003 Ford E250
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Your auto has four O2 sensors. Two upstream and two downstream; With two banks. Bank 1, sensor 1...and bank 2, sensor 1 are the two upstream (exhaust manifold before the catalytic). Bank 1, sensor 2 and bank 2, sensor 2 (other side of catalytic)
Code 1131= upstream; bank 1..sensor 1
Code 1151= upstream; bank 2..sensor 1
Code P0136 (generic code) bank 1..sensor 2 (questionable)
I wouldn't spend the money to purchase 3 sensors. Highly unlikely all three are bad; Cost is about $40/ ea.
Since there isn't a code for the cat's themselves, I would suspect the O2 circuit is malfunctioning. The rough idle is another clue.
Take an ohmmeter set it on X10 scale and measure the resistance from engine to body and body to negative post on battery terminal. You should read zero ohms (full needle deflection). If you do go buy two upstream O2 sensors. If you read
open or a high resistance run two straps from eng. to body...and body to neg.batt. post.
Posted on Dec 10, 2009
Some 2001-2003 F-150, 2004 F-150 Heritage and 2001-2003 E-150/250 vehicles equipped with a 4.2L engine may exhibit the malfunction indicator lamp (MIL) on with diagnostic trouble codes (DTCs) P1131 and/or P1151 (system too lean bank 1 or 2). This condition may be due to leaking isolator bolts/port gaskets in the upper-to-lower intake manifold mounting area. This condition is sometimes intermittent and may not be apparent on a warmed-up engine.
Perform a self test. If DTC P1131 and/or P1151 are the only codes stored in the powertrain control module (PCM) proceed to Step 2. If any additional DTCs are present, follow normal diagnostic procedures found in the PC/ED Manual.
Remove the upper intake and replace only the port gaskets (9H486) and isolator bolt assemblies (9S479). The new isolator bolt assemblies use a rubber material that is green in color, do not install the old isolator bolt assemblies with the black rubber material. Do not replace any other intake parts or gaskets.
While the upper intake manifold is removed, check the exhaust gas recirculation (EGR) orifices that are pressed into each primary port of the lower intake manifold. If any of the orifices are plugged with soot, clean and unplug them with a pick and solvent.
PART NUMBER PART NAME
1L3Z-9H486-AA Port Gasket
3F2Z-9S479-AA Isolator Bolt
Posted on Jan 13, 2010
those two codes are for the o2 sensors. both are the upstream sensors on the front and rear banks. so they are desinagted bank 1 sensor 1 and bank 2 sensor 1. them most common cause for this is faulty o2sensors , bad gas and of a poor running engine. so if your car runs good (no misfire) and gas is ok then replace the o2sensor witch is the very most common cause.
Posted on Jan 28, 2010
Testimonial: " Help With Problem But Where Are These O2 Sensor"
Tips for a great answer:
Oct 22, 2013 | Ford Mustang Cars & Trucks
May 17, 2011 | Ford Crown Victoria Cars & Trucks
Mar 12, 2011 | Ford F-150 Cars & Trucks
Jan 19, 2011 | 2000 Lincoln Town Car
Feb 17, 2010 | 2001 Ford F150 Styleside SuperCrew
Jan 13, 2010 | 2003 Ford F150 Regular Cab
Nov 29, 2009 | 2003 Ford Taurus
Nov 07, 2009 | 2001 Mazda Tribute
Apr 27, 2009 | Ford Explorer Cars & Trucks
Dec 15, 2008 | 2003 Ford E250
930 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: