Question about Cars & Trucks

Open Question

Check engine light is on got codes p0174,p0151,p0300,2004 gmc 4x4 crew cab

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 nissan frontier crew cab radio

the plastic around the gear shifter will pop up with a good pull, then turn it side ways to get over the shifter, then there are 2 screws the hold the bezel down around the radio and air vents, then just pull from the air vents it will pop off to reveil the screws to the radio

Posted on Feb 27, 2009

mechanicm639
  • 253 Answers

SOURCE: check engine light on,running rough and stalling.

171, 172, 174 are lean codes. P0300 is a missfire code. It sounds like you have a vaccuum leak. Listen for a sucking sound, try to locate it then repair it. Most likley a hose loose. Good Luck

Posted on May 07, 2009

  • 1986 Answers

SOURCE: My engine light has come on in my 2004 GMC crew

If the light was flashing when it came on, then it means your engine is misfiring.

A solid light can mean anything from a loose/faulty gas cap to a transmission issue.

This light comes on when the computer detects a fault of some sort in its diagnostic tests. If it keeps detecting this issue, the light will remain on. If the light turns off, then it has detected that the issue may no longer be present.

In order to find out what the exact reason was for your light, You need to have your car computer scanned to retrieve the code that the computer would have stored when the light triggered. Most garages will do this free of charge. The code will tell you what may have caused the light to initially turn on. Until you get this code, it's impossible to determine what parts need to be checked or replaced.

Posted on Oct 07, 2009

MNfisherman
  • 11896 Answers

SOURCE: 2004 GMC Sierra Crew cab 1st tune up

New spark plugs, new plug wires, new fuel filter, flush and refill radiator and new tranny fluid and filter, have tires rotated, chassis lubed, and have power steering fluid checked to see if it needs to be flushed and refilled.

Posted on Oct 08, 2009

techbuster
  • 5081 Answers

SOURCE: where is the cabin filter on a sierra 2004 gmc sle

The 04 SIERRA is behind a panel with 4 screws under the glove box...Remove the screws and cover and slide it out.There is actually 2 in there and it is easy once the cover is off.

Usually there are extremely detailed instructions that come with the new filter when you open the box...Follow these instructions it shouldn't be too hard.

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 GMC SIERRA 1500 4X4 CODES P0171 AND P0174 CHECK ENGINE LIGHT IS ON WONT PASS EMISION


Sometimes this is NOT a O/2 sensor issue ,,,,,If the P0171 is combined with the P0174 code, it's very likely that the problem is caused by an intake leak. If there are no intake leaks, the next step is to replace the air filter and clean the air flow meter. If the problem persist the front oxygen (O2) sensor may need to be replaced.
The P0171 code could also be caused may be caused by one or more of the following: debris on MAF sensor causing an incorrect reading, improper oil level, low or high fuel pressure or Engine Control Temperature (ECT) Sensor reading inaccurate,,,,,

Mar 24, 2015 | GMC Cars & Trucks

1 Answer

Is there a fuse for the third brake light 2001 GMC 1500 4x4 crew cab?


no it uses the same circuit the brake lights run off of. if the brake lights on the rear of the truck work and not the 3rd brake light then replace the bulb, check power and ground at the bulb socket.

Aug 16, 2014 | Cars & Trucks

1 Answer

Check engine light - Code p0171, p0172, and p0174


YO HAVE A VACUM LEAK AT INTAKE MANIFOLD GASKET OR HOSES THATS YOUR PROBLEM USE A CAN OF CARB CLEANER TO HELP FIND LEAK BY SPAING ARROUND INTAKE OK HOPE THIS HELPS BUT IM SHORE THATS YOUR PROBLEM RESON YOU REPLACE YOUR FUEL PRESSURE REGULATOR LEFT INTAKE LOSE OR PINCHED GASKETS OR LOSE HOSES TRY THAT OK

Nov 14, 2012 | GMC Cars & Trucks

1 Answer

I have a 2004 gmc sierra 1500 and the check engine light comes on if i go over 55 it starts to stall


you need to have the computer scanned for codes .check the fuel pressure at 55 mph.check the exhaust for restiction,bent,clogged convertor ,muffler.give me a shout back.wish you the best.

Oct 24, 2009 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

My engine light has come on in my 2004 GMC crew cab 1500. are there some things I can replace or check without taking it to a mechanic shop (80,000 miles)


If the light was flashing when it came on, then it means your engine is misfiring.

A solid light can mean anything from a loose/faulty gas cap to a transmission issue.

This light comes on when the computer detects a fault of some sort in its diagnostic tests. If it keeps detecting this issue, the light will remain on. If the light turns off, then it has detected that the issue may no longer be present.

In order to find out what the exact reason was for your light, You need to have your car computer scanned to retrieve the code that the computer would have stored when the light triggered. Most garages will do this free of charge. The code will tell you what may have caused the light to initially turn on. Until you get this code, it's impossible to determine what parts need to be checked or replaced.

Oct 07, 2009 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

2001 fronteer crew 4x4 dash lights


Check instrument panel fuse first. It would be labled on the fuse door or in manual. If not blown i would suspect the dimmer switch. There are to many bulbs in a instrument panel for them all to blow at one time.

Feb 15, 2009 | 2001 Nissan Frontier Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...