Question about Jaguar XJ6

1 Answer

Exact location of inertia switch - XJ6 Jaguar Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jaguar Master
  • 17,970 Answers

Send us exact year model and engine size.

Posted on Feb 17, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1129 Answers

SOURCE: locatio of inertia switch 1990 lincoln town car

Check just above the carpet on the passenger side where your feet go under dash.

Posted on Jul 02, 2009

  • 73 Answers

SOURCE: 2001 sl2 saturn inertia switch

if you are refering to a inertia switch like on a ford that kills the fuel pump in a crash, the saturn does not have one

Posted on Mar 31, 2009

  • 100 Answers

SOURCE: e-150 fuel pump inertia switch location

on some fords it is on pass side kick panel you have to feel in a hole and you will feel a reset button,hope this helps

Posted on Feb 14, 2010

  • 5687 Answers

SOURCE: location of inertia switch/fuel pump

Yes it can. It doesn't take much like slamming a door or dropping a load of parts. There is only a magnetic ball inside the contacts and it is a wonder that Railroad tracks and Potholes do not trigger more shutoffs. All you do is find the switch and hold down the button on it for about 3 seconds.

Then try starting the van without slamming the doors shut until it is running. If the Inertia switch does not help check the fuse panel, then the relay. The relay should either be in the Black powerbox group or in with the fuseholders.

Posted on Apr 18, 2010

  • 1 Answer

SOURCE: inertia switch

Does a 1997 Chevy Cavalier have a inertia switch if so where is the location

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the interia switch located on a 1996 isuzu rodeo? EXACT LOCATION...

Look for the inertia safety cutoff switch, usually the right side, Passenger foot wheel or rear corner and see if you can reset should be in your owners manual.

Dec 16, 2015 | Isuzu Cars & Trucks

1 Answer

Location of inertia switch

If it has an inertia switch, it will be on the passenger side under the kick panel under the glove box.

Apr 20, 2014 | 2000 Mazda 626

1 Answer

Won't start has spark to spark plug.

Check for Inertia switch on All Ford products. Usually its located behind the floor kick panels or inside trunk. This part disconnects the fuel pump power.

If you have Ford, Lincoln, or Mercury look up your specific vehicle under "Your Car" Inertia switch location on the internet for exact location.

Or a small wisp of starting fluid will reveal if the engine needs fuel. Besides the Inertia switch you can test the fuel pressure port on the fuel rail. You also have a fuel pump Relay and a fuse and in worst cases your fuel pump could be bad.

Sep 17, 2013 | Cars & Trucks

1 Answer

Inertia switch located

The ony manufacture that uses a inertia switch for the fuel pump is ford.

I’m happy to assist further over the phone at

Sep 08, 2013 | Hyundai Accent Cars & Trucks

2 Answers

Won't start, fuel staved, started with starter fluid, but will not stay running

1 replace the fuel filter 2 check the fuel pump to see if pumping fuel

Feb 27, 2013 | 2004 Ford Escape

1 Answer

Where exactly is the inertia switch on a 99 mercury villager

go to villager-quest yahoo group for more help

Inertia Fuel Shutoff (IFS) Switch Removal
  1. Remove the LH scuff plate.
  1. Remove the LH lower A-pillar trim panel.
  1. Remove the inertia fuel shutoff (IFS) switch.
    1. Disconnect the electrical connector.
    1. Remove the screws.

Sep 30, 2011 | 2000 Mercury Villager

1 Answer

Need the location of the fuel inertia fuel shut off switch

If you'd have included the model and year I could give you an exact answer.
On Fords, the inertia switch is either in the trunk near the driver side arm, or under the front passenger side kick panel.

May 10, 2011 | Ford F-350 Cars & Trucks

2 Answers

Where exactly is the fuel restart button on a 92 mercury topaz gl

It's located on the inside of the trunk on the drivers behind the carpet.

Aug 03, 2010 | 1992 Mercury Topaz

2 Answers

I need to know where the reset switch is for the fuel pump.

the reset switch is located at the front "a" pillar near where your foot would kick, sometimes called the kick panel for this reason.....the switch is called an inertia switch becuase it shuts off the fuel in the event of a collision, now im from australia, where the driver sits on the right and the inertia switch is on the left, it is behind the plastic panel, be careful not to break as you bend it back,,,,,,,good luck

Jul 28, 2010 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80531 Answers


Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides