Question about Cars & Trucks

Open Question

Intake manifold torque sequence for a jaguar S-TYpe 4.2L

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

Ad
chuck943
  • 783 Answers

SOURCE: Ford 460 Intake Manifold Torque spec

22 to 35 ft lbs

Posted on May 22, 2009

  • 279 Answers

SOURCE: looking for torque specs and sequence of both

Lower intake bolts 11 ft. lbs start in the center of the intake and work your way out cross from side to side.Tighten the upper intake bolts with the same procedure with 89 inch pds.Be sure to apply threadlocker to the lower intake bolt threads.

Posted on Feb 07, 2010

arauzvictor1
  • 466 Answers

SOURCE: need head bolt, intake manifold, and exhaust torque specs

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Posted on Mar 06, 2010

ZJLimited
  • 17970 Answers

SOURCE: intake manifold torque specs and

8ef3de6.jpg

Fig. Exploded view of the upper and lower intake manifold and fasteners

- Position the rocker arms in their original locations and tighten to the proper specifications.

- Install lower the intake manifold attaching bolts. Apply sealant or equivalent thread locking compound to the threads of bolts. Tighten the vertical bolts first, then the diagonal bolts to 115 inch lbs. (13 Nm).

- Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).

Hope helps (remember to rate this).

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bolt torque sequence on 1991 jaguar xj6 4.0 intake manifold?


intake manifold or head gasket? i know head gasket need a sequential order followed by how many degrees and Lbs of pressure. if its on the intake i doubt it needs an specific torque. just try not to crack the intake manifold since its made of plastic.

Oct 29, 2012 | 1991 Jaguar XJ6

1 Answer

Intake Manifold tightening sequence plus torque specs


start in the middle and alternate left to right and the torque on a alloy manifold will be around 14lbs or a nip with a 3/8th drive rachet ,any water passages use contact adhesive around the water ports .

May 25, 2012 | Chevrolet Corsica Cars & Trucks

1 Answer

Toquer on the intake


start in the center working in an expanding square pattern crossing over the manifold on the first 2 bolts. tighten in 3 steps. these are low torque fasteners, don't over tighten & use locktite.
If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the lower intake manifold bolts.
Install the lower intake manifold bolts.

Notice: Proper lower intake manifold fastener tightening sequence and torque is critical. Always follow the tightening sequence, and torque the intake manifold bolts using the 3 step method. Failing to do so may distort the crankshaft bearing bore alignment and cause damage to the crankshaft bearings.

Tighten the lower intake manifold bolts.

from front of engine tighten 2 bolt back left side, then 3rd bolt back right side, then 3 bolt back left side, then 2nd bolt back right side, then back bolt left side, back bolt right side, then front bolt left side, then front bolt right side

Tighten the bolts on the first pass in sequence (1-8) to 3 N·m (27 lb in).
Tighten the bolts on the second pass in sequence (1-8) to 12 N·m (106 lb in).
Tighten the bolts on the final pass in sequence (1-8) to 15 N·m (11 lb ft).

Jan 15, 2011 | 1996 Chevrolet Blazer

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


    4022caa.jpg

    Fig. Intake manifold bolt torque sequence 2.7L engine

    Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

    Hope helps (remember to rate this answer). Good job.

    Oct 11, 2010 | 2002 Chrysler Sebring

    1 Answer

    Need to replace intake manifold how do you do this


    Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

    3.8L Engine
    VIN 1 Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Relieve the fuel system pressure.
    3. Drain the cooling system.
    4. Remove or disconnect the following:
      Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
    To install:
    1. Install or connect the following:
      Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    VIN K Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Disconnect the negative battery cable.
    3. Drain the cooling system.
    4. Relieve the fuel system pressure.
    5. Remove or disconnect the following:
      Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

      a5adffa.jpg
      Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
    To install:


    140d431.jpg
    Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


    4950e4f.jpg
    Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
    1. Install or connect the following:
      Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    Hope this help (remember rated this).

    May 17, 2010 | 2001 Pontiac Bonneville

    2 Answers

    Need torque specs for a 2001 jeep cherokee intake manifold


    Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

    6a7ecad.jpg

    Fig. Intake manifold torque sequence-3.7 & 4.7L engines


    Hope this help (remember comment and rated this).

    May 07, 2010 | 2001 Jeep Cherokee

    2 Answers

    2001 jaguar S type v 6. I need to replace the valve cover gasket. Does any one have the torque sequence and torque values for the bolts?


    Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

    Sep 29, 2009 | 2002 Jaguar S-Type

    Not finding what you are looking for?

    Open Questions:

    Cars & Trucks Logo

    Related Topics:

    154 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22258 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...