Question about 1991 Chevrolet Corvette

Open Question

How to change water pump on L98 CORVETTE - 1991 Chevrolet Corvette

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 62 Answers

SOURCE: Need the firing order for

1-8-4-3-6-5-7-2

Posted on Sep 02, 2010

Testimonial: "Very fast response, and just what I needed."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car runs hot while idling changed thermostat cooling fan is working but temperature still goes up to 240 degs


Try a full cooling system overhaul. completely flush the rad, check all hoses, frewh coolan of the appropriate type and to the correct concentratin. Bleed the system.check the thermostat is opening closig at the appropiate tem[erature and that the fan is running as fast as it should. The temp really should not ne that high I think. Also ensure the system is properly bled. If too much heat is generated your engine will die so it is important to deal with this issue

Jun 04, 2015 | 1991 Chevrolet Corvette

2 Answers

My 1994 corvette starter clicks and spins but wont start


sounds like you need a new distributor.... if you had a new water pump put in lately and didnt change the distributor that would be your main problem. The water pump in located in front of distributor, if that leaks it will short out and fry the distributor. Always change distributor when water pump goes.

Jun 20, 2014 | 1993 Chevrolet Corvette

1 Answer

1993 corvette will not start


Bad distributor..... causes could be if you had water pump problems before and water leaked behind pump onto distributor it will fry..always replace distributor when water pump goes

Apr 16, 2014 | 1993 Chevrolet Corvette

2 Answers

I have a 1991 L98 Tuned Port Corvette. When I turn the key to the on position the fuel pressure reads 50psi but falls back to zero within 2-3 seconds and the car won't start. I can spray injector cleaner...


It could be a cam sensor. If the sensor isn't sending a signal to the computer then it will not allow the fuel pump to continue running after 2-3 seconds. Since you have spark and fuel pressure upon initial start this could be your problem.

Dec 17, 2010 | 1991 Chevrolet Corvette

1 Answer

How long should the fuel pump relay stay energized before going off on a 1991 chevy corvett. when i first cut my switch on it only energizes for about 2 secounds then drops out. the car is hard to crank...


it should only stay on for a few seconds,you have an underlying problem.it could be either your fuel pressure regulator or the check valve in the pump itself might be letting the fuel drain back into the tank,im guessing the car only does it after it has been sitting for a little while and after the initial hard start it will keep starting normally,the easiest way to test it is to put a fuel pressure tester on it and start the vehicle or just pressurize the lines by turning the key on and see if the pressure drops,if it does, pressurize the lines again and crimp of the line from the pump wherever it is rubber with a pair of vise grips and see if it drop then..if it doesnt it will need a pump if it does it will need a fuel pressure regulator,im guessing this car has a L98 5.7 ltr TPI engine in it

Oct 12, 2010 | 1991 Chevrolet Corvette

2 Answers

How do you change the distributor cap and coil on a 1991 corvette


there are four screws that u push down on and turn counter clockwise as you push down, they hook under the distributor, then disconnect the wiring harness and pull the cap off

Sep 17, 2009 | 1991 Chevrolet Corvette

2 Answers

94 fleetwood brougham LT1 overheating


This engine has a cam driven water pump. If the gear is sheared/broken it can cause this issue.

Feb 23, 2009 | 1994 Cadillac Fleetwood

1 Answer

Clutch knock at shut down


THROW OUT BEARING IS MAKING THE KNOCK NOISE , I AM REPAIRING A 1991 L98 CONV. RIGHT NOW FOR THE SAME ISSUE!

Dec 09, 2008 | 1991 Chevrolet Corvette

Not finding what you are looking for?
1991 Chevrolet Corvette Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...