Question about Ford F-150

Open Question

Replace dome light bulb in a 1991 ford ranger

Can't remove cover

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

  • 1861 Answers

SOURCE: 1998 toyota camry interior dome light replacement

Look closely at the cover. You will see a small slot. Insert a small flat blade screwdriver, and pry it off. Very easy..

Posted on Nov 10, 2008

osoteddy
  • 1 Answer

SOURCE: How to replace map & dome light bulbs on a 2008 Ford F-150 Super

2008 Ford F-150 SuperCrew Cab (without moon roof or rails): How to replace the map light bulbs.  First, you'll need a "trim pad remover."  It is a tool with a screwdriver handle and the metal part has a 'smooth' forked tongue (see Snap-on Stock#: A177A for picture).  Go to the center counsel and "gingerly" work around he counsel and pull down at the same time.  The counsil is held in by six snap in tongs.  It should remove pretty easily.  once down, you'll see where the bulbs are.  Unscrew and replace.  Now, just line up the tongs and gently bump or hit the pressure points (where the tongs are) and it should snap into place.  It should take no more than five minutes, tops.

Posted on Nov 17, 2008

dr_greg
  • 192 Answers

SOURCE: Replace dome light bulb

insert a flay eyeglass scrwdriver in between the plastic lens and base, pry gently , the lens will pop out... u should see the small sections where to insert the screwdriver to pry off the lens

Posted on Apr 05, 2009

  • 32 Answers

SOURCE: Help changing dome light bulbs in 2005 Accord

This is a real pain, took me forever to find mine... there is a little TINY slot that you can fit a VERY small flat head screwdriver in to pop it off.

Dont worry, the plastic is durable, just try to use a precision screwdriver if you have one and basically pry it open. it really will just Pop off once you get in there

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear dome light on 2004 edpedition


if you haven't figured it out yet ,you pull off the rear headliner center plastic piece,it just pulls down ,then remove the 2 puch pins on rear of headliner, then pull out light fixture and replace bulb

Oct 19, 2014 | 2004 Ford Expedition

1 Answer

Ford taurus tss 2004 map lights work but dome light wont come on


It is possible the bulb in the dome light is burnt out or there is a bad connection @ the bulb. That is at least where you start. you will need to remove the dome light cover & wiggle the bulb while the door is open, or best to have two doors open to remove the possibility of a faulty switch. If it still doesn't flicker or start to work remove the bulb & inspect it to see if the filament is broken. If you can't tell best to replace the bulb & try again.
Please advise if you need more help.

May 29, 2014 | Cars & Trucks

1 Answer

How do I replace dome light on Matrix 2009


Remove the key from the ignition. Make sure the doors are closed, so the new bulb does not illuminate when you are installing it.
Make sure the dome lighting switch is turned to the "Off" position. Pry the plastic lens away from the dome light. Use a small, flat-head screwdriver.
Push back the side bulb clamp. Pull out the old dome lightbulb. Wipe the area with a paper towel if it is dirty.
Wrap the new bulb in a paper towel. Insert it into the dome lightbulb holder. Push it up gently to secure it.
Turn the switch to "On" to test the bulb. Reposition the cover and push up to lock the clips into place.

May 28, 2013 | Cars & Trucks

2 Answers

How to replace interior dome light bulb?


1) Remove the key from the ignition. Make sure the doors are closed, so the new bulb does not illuminate when you are installing it.

2) Make sure the dome light switch is turned to the "Off" position. Pry the plastic lens away from the dome light. Use a small, flat-head screwdriver.

3) Push back the side bulb clamp. Pull out the old dome lightbulb. Wipe the area with a paper towel if it is dirty.

4) Wrap the new bulb in a paper towel (oil from your skin will shorten its life). Insert it into the dome lightbulb holder. Push it up gently to secure it.

5) Turn the switch to "On" to test the bulb. Reposition the cover and push up to lock the clips into place.

If the bulb doesn't work, you've got a bad switch somewhere, probably on the drivers door.

Dec 26, 2010 | 2006 Toyota Highlander

2 Answers

I can't figure out which bulb to use to replace the bulb in the dome light.


Hello. Go to any auto parts store and tell them what you hope to do. They have a data base which will tell them which bulb is appropriate for your application.

Joe

4 thumbs up please. ty

Oct 20, 2010 | 1992 Ford Ranger

1 Answer

Have a 04 super cab ranger tremor and when i turn the dome light and the door ajar light comes on how can i fix that


turn off the dome light.


the door opens, it turns on the dome light, so the wire that goes from the door switch gets powered up and makes your dome light come on. if your door is closed, and you turn on the dome light, the same wire gets power and is actually sending power to your light bulb on the dash.
just ignore it , or get a diode and put it on the correct wire, and it wont allow the electricity to flow back towards the light bulb when you put the dome light on.

Jul 31, 2010 | 2004 Ford Ranger

2 Answers

My 1995 ford ranger pick up speedometer, radio, break lights, wipers and turn signals dont work


On the ford ranger wiper motor not working, this is how u fix it. I am a licenced autobody mechanic for mercedes and my son bought a ford ranger and of course the wipers were not working-neither did the dome light and door chime.I told my son too replace all fuses ,switch and motor. And still nothing.Remove radio there is a pcm in behind- ours was unpluged. When we plugged it in the door bell would not shut off and the dome light stayed on. In stead of unplugging the pcm remove the light if wd40 does not work on the door latches. And to stop the door bell ringing remove the plastic cover around the ignition and their is a single wire with a blue connector just remove the wire it is the wire closest to the key and tape up the end and problem solved guarenteed . my email is frameman127@yahoo.ca I will walk u through it .

Jul 24, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to change blinker light bulb


94 ranger is all I have. Maybe similar

Parking, Turn and Front Side Marker Lamps, Ranger Removal and Installation
  1. Remove one nut that attaches the parking lamp to the opening panel in radiator grille .
  1. Pull parking lamp away from vehicle to disengage the two barbed retainers.
  1. Twist the lamp socket and remove from lamp. For installation, follow removal procedures in reverse order.

Mar 09, 2009 | 1991 Ford Ranger Supercab

3 Answers

Dome light 1998 Ford Ranger super cab


spray both door latches with penetrating oil and open and shut the doors numerous time... should fix the problem

Sep 16, 2008 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...