Question about Mitsubishi Expo

Open Question

ABS light stays on in 2000 Mitsubishi RVR and can't be recognised by a mechanic's diagnostic computer

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 261 Answers

SOURCE: when does one engage the ''L'' gear when driving a mitsubishi rvr c

the L gear is Gear # 1 and likewise 2 is second gear, you utilise this in case you are going down on a slop especially icy or snow condition all it does is runs just on 1 or 2 respectively without changing whichh gieves more traction on the road.

Posted on Dec 15, 2008

  • 328 Answers

SOURCE: Hello, I'm from USA visiting

here's the link for the owners manual http://www.japaneseautospares.co.uk/ownershandbooks/mitsubishi.htm#rvr
sorry i dont know much about this vehicke or where the jack would be:(
hope this helps....Good luck!

Posted on Dec 15, 2008

  • 580 Answers

SOURCE: ABS and ASC warning lights stay on 2000 530d

Check to see if your brake pads and rotors are in good condition. Or if you have replaced the pads yourself and have not reset the wheel sensors this would cause the ABS Antilock Brake System light and the ASC Automatic Stability Control light to stay on as the ASC uses the ABS brakes with computer assistance to control the car

Posted on Jul 08, 2009

  • 1 Answer

SOURCE: 1995 GMC Sierra Z71 ABS light stays on

yo man, idk if this is exactly what your problem is but my 1991 gmc sierra was doing the same fuckin thing and ****, and i took it to the gm dealer and had them look at it and my connectors and my ignition switchs were fried, also my truck was having a problem shitfing once those went but i also had that problem, perhaps yours is somehwta liek that as well... hope i could help

Posted on Aug 08, 2009

  • 1757 Answers

SOURCE: set timing on mitsubishi rvr diesel

CLICK on the following LINK. I beleive it has the Diagrams for your Timing Belt that you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1993/make/mitsubishi/model/precis/1993_mitsubishi_precis_timing_belt_diagram_marks.htm

Posted on Mar 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs light stay on and wont go off how to fix it


Get thee to a mechanic! The light indicates a fault in the ABS system. That means that you likely do not have Anti-lock brake functionality. It is likely that one of the sensors of the system is not functioning. This requires diagnosis and repair. If you do not have the appropriate diagnostic tools and the knowledge to apply the results you need to go to a qualified mechanic.

Oct 27, 2014 | Cars & Trucks

1 Answer

TRACTION CONTROL LIGHT STAYS ON


Is the ABS light on too? These are inextricably linked systems, so you might want to run a diagnostic computer on the vehicle to pull up any fault codes, as one system can affect the other, and faults with the traction control aren't always with the traction control circuit.

Nov 13, 2012 | 2000 Pontiac Grand Prix

2 Answers

After changing oils with my mitsubishi rvr 1998, the gear doesn't shift automatically when driving uphill aside from ajerk sound


The following are the general instructions on the start of diagnosing any electronically controlled engine or transmission problem.

The engine and the automatic transmission (transmission control is only for automatics, engine is still computer controlled no matter the transmission type) in this vehicle are computer controlled and in most cases when a fault occurs a fault code is stored in the memory of the computer control module. There are exception to this, such as the Mass Airflow Meter and fuel pressure problems. What must be done is to have all the basic testing done such as a scan of the system for fault codes as well as a check with a live data scanner tool for engine functions that are not within range of normal, a trained technician is required to know what is correct and what isn't, then based on careful diagnostics done from a factory repair manual the correct part is replaced or the wiring repaired or the computer replaced (known as the PCM), which is very rarely the problem. Other basic checks must be done as well such as mechanical problems with the engine as well as engine state of tune and mileage on the engine. The transmission can have mechanical issues as well such as no gear engagement at all or a failed pump or other pressure related problems. Also engine mechanical problems ca cause many drive-ability related problem such as rough idle and other symptoms


Oct 18, 2012 | 1992 Mitsubishi Diamante

1 Answer

What can be wrong when the ABS light stays on?


You'll need to have the computer scanned for trouble codes, and some code readers will not access body computers.

Jul 11, 2012 | 2000 Volkswagen Beetle

1 Answer

I have a 2000 GMC Sierra. Brake Light and ABS warning light comes on frequently. Sometimes it's there othertimes not. Have replaced the sensors, replaced rotors and pads, cleaned gound on the frame...


I would recommend checking for diagnostic trouble codes in the ABS system. If there is a diagnostic code C0265 set, then you're most likely looking at an ABS computer replacement. This is a common failure on these trucks. GM calls this computer an EBCM, or Electronic Brake Control Module. This is the controller for antilock brakes and is mounted directly to the ABS pump motor assembly. Last time i checked, these things were going for about $900 at the dealer.

Aug 08, 2011 | 2000 GMC New Sierra 1500

1 Answer

4X4 green inidcator light flashes and ABS light


Hi, you will probably have to take to mitsubishi dealer and have them scan diagnostics....but sounds like the o ring has busted in transfer case. will it shift in and out of 4wheel drive? If not don't drive it...it will cause alot of damage.

Jul 26, 2009 | 2000 Mitsubishi Montero

1 Answer

Park Brake Light Stays On


One the brake pedal is a buttom switch,It may be sticking or may just need adjusted.

Jan 13, 2009 | 1994 Mitsubishi Expo

2 Answers

When does one engage the ''L'' gear when driving a mitsubishi rvr c


the L gear is Gear # 1 and likewise 2 is second gear, you utilise this in case you are going down on a slop especially icy or snow condition all it does is runs just on 1 or 2 respectively without changing whichh gieves more traction on the road.

Dec 15, 2008 | 1987 Mitsubishi Passenger

1 Answer

Abs on dashboard stays lit all the time.


The only way to know axactly what happen is with a diagnostic computer.
Because the ABS use a Speed sensor on each of the wheels.
Hydraulic selenoids on the ABS box or Module..
If the light is on. its mean the Anti Lock Brake System is inactive., You gonna brake like any car with no ABS.
I hope this information work for you.

Jun 01, 2008 | 2000 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...