Question about Cars & Trucks

Open Question

%cold working received for 12 mm material? - Cars & Trucks

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Honda crv dimensions

HondaCRV is an best Suv car across the world as it the style, good mileage and best in class interior features to beat competition in the auto industry.Here I have mentioned the dimension of Honda CRV 2WD, take a look
1) Length:
4545 mm

1820 mm

1685 mm

2620 mm

5)Front Track
1565 mm

6)Rear Track
1565 mm

7)Ground Clearance
170 mm

8)Kerb Weight
1475 kg

9)Gross Vehicle Weight
1830 kg

10)Boot Space
490 litres

11)Fuel Tank Capacity
58 litres

12)Minimum Turning Radius
5.5 meter
Check out the Test Drive video of Honda CRV.

Oct 11, 2017 | Honda Cars & Trucks

1 Answer

What is the specs on tappet cover settinigs

I assume you are asking for the valve clearances?

The 1.3 and 1.6 are adjusted hot to 0.2 mm inlet and 0.3 mm exhaust.

The 1.6 GT model are adjusted cold to 0.15/0.25 mm inlet and 0.2/0.3 mm exhaust.

The 1.8 diesel is also adjusted cold to 0.2/0.3 mm inlet and 0.25/0.35 mm exhaust.

Nov 04, 2015 | 1984 Toyota Corolla

2 Answers

What is the valve clearance on a kia 2700

inlet 0.30mm cold
exhaust 0.38mm cold

Aug 29, 2015 | Kia Cars & Trucks

1 Answer

1993 Toyota Celica trunk will not open. The lock is stuck in a middle position. Can I go through the back seats to fix the problem?

Crawl into the back and remove all of the screws that hold the back plastic panel on.

the back seat is removed by pulling up the rear seat front cushion.
Then you get access to the seat back.
There are 2 12 mm bolts that hold the seat back AND the side arm rest.Lower arm rest bolts are at the bottom. 12 mm.
Tie the seat belts back.
The seat back bolts are at the bottom. 12 mm.

B-4 you try that ordeal......
Use lock eaze on the lock cylinder.
Graphite spray can.

Try pulling the trunk key back out.
maybe a slide hammer..
Put down pressure on the trunk lid,first.
Have a friend sit on it...

WD-40: last resort.

Work the key in the cylinder after you dowse the key hole with that crap/chemical.
If the key brakes off,into the trunk you go.

Mar 09, 2013 | 1993 Toyota Celica

1 Answer

93 accord timing belt installation

  • Car jack
  • Jack stands
  • Torque wrench
  • Chain wrench
  • 3/8 inch drive ratchet
  • 1/2 inch drive ratchet
  • 10 mm wrench
  • 12 mm wrench
  • 10 mm socket (3/8 inch)
  • 14 mm socket (3/8 inch)
  • 17 mm socket (1/2 inch)
  • 19 mm socket (1/2 inch)
  • Timing belt
  • Balancer belt
  • Bottle of Liquid Paper

  • Disconnect the negative battery terminal. Using a ½-inch-drive ratchet and the 19 mm socket, turn the center bolt on the crankshaft so that number-one cylinder piston is at top dead center (TDC). You will know you ware at TDC when the mark on the crank is in alignment with the arrow on the timing cover.
  • Disconnect the cruise control connector and remove the cruise control actuator. Loosen the upper mounting bolt with the 14 mm socket. Use a 12 mm socket to loosen the lower nut then use a 10 mm socket to loosen the adjuster from the power steering pump and remove the belt.
  • Loosen the upper air conditioner mounting bolt using the 14 mm socket. Use the 12 mm socket to loosen the lower nut and adjusting bolt on the alternator and remove the alternator/AC belt. Remove the valve cover using a 10 mm socket.
  • Place the jack behind the left front wheel where the arrow is located indicating the jack location, and raise the vehicle. Put the jack stand under the subframe behind the jack, then lower the jack. Remove the left front wheel for easy access to the crank pulley. Using a block of wood atop the jack, place the jack under the oil pan and lift with slight pressure to hold the engine in place. Remove the side engine mount using a 17 mm deep socket.
  • Take off the dipstick, pipe tube and upper timing cover using a 10 mm socket.
    Then remove the timing belt adjuster rubber seal without loosening the adjuster nut. Take off the crankshaft pulley bolt. Use the chain wrench to hold the the crankshaft pulley while turning the crankshaft pulley bolt with a 19 mm socket. Use the 10 mm wrench and 10 mm socket to remove the bolts on the lower cover. Remove the lower cover and mark the location of the cam, crank and balancer shaft with Liquid Paper. Remove the balancer shaft belt and timing belt. Install the timing belt and the balancer shaft belt in the reverse order of removing them. During Installation of the crank pulley, coat the threads of the crank pulley bolt with engine oil and tighten it to 159 foot-pounds. Finally, adjust the tension of the power steering and alternator belts as well.

    Feb 03, 2011 | 1993 Honda Accord

    1 Answer

    Location of starter 1991 toyo camry 2.0 lt and tools needed to r&r starter

    It is at the 12 o'clock positition on the transmission and held in with 2 14 mm bolts the wire is held on with a 12 mm nut

    Jun 19, 2010 | 1991 Toyota Camry

    2 Answers

    What type of air filter is best and how do i change it myself?

    I always used K&N filters; check this information and links for 2004 FORD Explorer Sport Trac 4.0L V6 F/I - (All Models):

    Part 33-2106-1 Product Specifications
    Product Style: Panel Air Filter
    Height: 1.188 in (30 mm)
    Outside Length: 9 in (229 mm)
    Outside Width: 7.688 in (195 mm)
    Filter Material: Cotton Gauze
    Filter Re-Oiling Amount: 1.03 oz (31 ml)
    Weight: 1.3 lb (0.6 kg)
    Product Box Length: 10.44 in (265 mm)
    Product Box Width: 1.75 in (44 mm)
    Product Box Height: 11.56 in (294 mm)


    Other alternative, if you can make it, install one new intake system with a conic filter and increase your HP (this work so fine in my Jeep 5.2L V8)...

    Part 57-2529-1 Product Specifications
    Product Style: 57 Series FIPK
    Estimated Horsepower Gain: 6.88 HP @ 5243 RPM
    Type: Gen II
    Replacement Filter: RF-1048
    Street Legal In All States: Yes
    TUV Approved (Europe): No
    Weight: 8.4 lb (3.8 kg)
    Product Box Length: 20.25 in (514 mm)
    Product Box Width: 12.25 in (311 mm)
    Product Box Height: 12.25 in (311 mm)


    Hope this help (remember rated and comment this).

    Mar 23, 2010 | 2004 Ford Explorer Sport Trac

    1 Answer

    I just need to know what tools i would need to change a cv axle on a '91 dodge caravan


    Jul 23, 2009 | 1991 Dodge Caravan

    1 Answer

    Tappet settings for isuzu trooper 1996

    For the 3.1 diesel its 0.016" cold .
    petrol is
    Valve Clearance Standard Value (cold)
    Intake: 0.23 mm–0.33 mm
    (0.0091 in–0.0130 in)
    Exhaust: 0.25 mm–0.35 mm
    (0.0098 in–0.0138 in

    Apr 25, 2009 | 1996 Isuzu Trooper

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    32 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts


    Level 3 Expert

    80417 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    john h

    Level 3 Expert

    15314 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides