Question about 2004 Mitsubishi Endeavor

1 Answer

How many oxygen sensors does a 2004 endevor have

Posted by on

  • santiagooros
    santiagooros Feb 18, 2012

    i see the co2 sensor in front of engine,but where are the other 2? are they visable from the front of the engine?

  • santiagooros
    santiagooros Feb 19, 2012

    i can not find the sensors in back of engine,are they visable from the front of engine,how do i get to them?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,970 Answers

Hi Santiago:
There is a sensor located before a emission device called a catalytic converter that is located on both sides. The sensors in the back of the engine are called O2 sensor 1 bank one, (sensor before the catalytic converter) and O2 sensor 2 bank one (located after the converter).

On the front of the engine, going down you have two as well for there is a converter on both sides. first one coming from the engine is O2 sensor 1 bank 2 and then your failed one after the converter, O2 sensor 2 bank 2.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Posted on Feb 17, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can u send picture of sensor for Mitsubishi endevor 2004 turbine/input shaft speed sensor location


is it a 3.8 engine ?
if so if you remove the air filter hose off the intake you will see it on top of the transmission bellhousing there's only 2 of you get a new one its obvious which one it is then

May 01, 2016 | Mitsubishi Cars & Trucks

1 Answer

ERREURPO132 DODGE CARAVAN 3.3 LITRE 2004


This involves the front oxygen sensor on Bank 1. This code indicates that the heated oxygen sensor reading incorrectly
You will likely not notice any drivability problems.A code P0132 may mean that one or more of the following has happened:
  • The oxygen sensor heater circuit is shorted out
  • The wiring to the sensor is broken / frayed (less likely)
The simplest thing to do is to reset the code and see if it comes back.If the code comes back, the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
  • Check for wiring problems (shorted, frayed wires)
  • Check the voltage of the oxygen sensor

Sep 10, 2014 | 2004 Chrysler Voyager

1 Answer

Oxygen sensor connector 2004 Kia Sorento


The removal procedure of Oxygen sensor connector for 2004 Kia Sorento is explained in below link. Please refer through it.

531fa0c2-d966-466f-8ade-159cb41e391a.jpg


0ebd0374-2764-42ba-a725-ed8fe7b650c7.jpg

Jun 11, 2013 | 2004 Kia Sorento

1 Answer

How many oxygen sensors does a 2004 endevor v6 have


Hi there:
There is a sensor located before a emission device called a catalytic converter that is located on both sides. The sensors in the back of the engine are called O2 sensor 1 bank one, (sensor before the catalytic converter) and O2 sensor 2 bank one (located after the converter).

On the front of the engine, going down you have two as well for there is a converter on both sides. first one coming from the engine is O2 sensor 1 bank 2 and then your failed one after the converter, O2 sensor 2 bank 2.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Cars & Trucks

1 Answer

I have the oxygen sensor for my 2004 mazda3 2.3L, but i have no clue how to physically replace it myself. what are the steps to replacing it?


WELL YOU NEED A OXYGEN SENSOR SOCKET, YOU CAN BUY IT AT ANY AUTO PARTS STORE.YOU NEED CRANK VECHICLE FOR ONE MINUTE TO GET FRONT EXHAUST PIPE LITTLE WARM NOT TOO HOT.SAFELY RAISE SUPPORT FRONT VECHICLE ON JACK STANDS ANF PARK VECHICLE ON LEVEL SOLID GROUND.WEAR SAFETY GLASSES LOOK TOWARD FRONT EXHAUST PIPE JUST ABOVE THE SILENCER. SPRAY PENETRATING OIL AROUND OXYGEN SENSOR WAIT UNTIL PENETRATING OIL SOAK IN THREADS THEN REMOVE DISCONNECT OXYGEN SENSOR ELECTRICAL CONNECTOR THEN USE SPECIAL OXYGEN SENSOR SOCKET AND 3/8 RATCHET WRENCH REMOVE THE SENSOR.THEN INSTALL NEW OXYGEN SENSOR TORQUE IT TO 22 - 36 FT LBS.AS A MECHANIC I WOULD WEAR LONG SLEEVE WORK SHIRT OR COVERALLS USE LEATHER TYPE GLOVES TO KEEP BURNING HANDS OR ARMS ON THE EXHAUST PIPE AREA STILL BE HOT ENOUGH TO BURN SKIN.

Aug 10, 2011 | 2004 Mazda 3

1 Answer

I have p044 code for Camry 2004


P0044 - HO2S Heater Control Circuit High (Bank 1 Sensor 3)

The P0044 is set when the ECM detects an excessively high voltage through the heated oxygen sensor heater circuit

Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit fuse
- Faulty Engine Control Module (ECM)

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

zjlimited_245.gif

Hope helps (remember to rate this answer).

Mar 15, 2011 | 2004 Toyota Camry

2 Answers

The engine light and VSC light are on (Vehicle Singapore 2004 Lexus RX 300. Diagnostics report Error code P0037


your o2 sensor is bad. vsc will go on for any small DTC displayed on the MIL (cel)

P0037 LEXUS P0037 LEXUS - Oxygen Sensor Heater Control Circuit Low Bank 1 Sensor 2 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
Possible causes - Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) When is the code detected? The P0037 is set when the ECM detects an excessively low voltage through the heated oxygen sensor heater circuit P0037 LEXUS Description Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. The faster the heated oxygen sensor reaches that temperature the faster the sensor will start sending an accurate signal to the Engine Control Module (ECM).

In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECMcontrols the heater element circuit by allowing current flow to ground.

The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.

o2_heater_circuit.gif

Mar 14, 2011 | 2004 Lexus RX 330

1 Answer

How to relace oxygen sensors yourself on a 2004 armada


FIRST OF ALL YOU NEED TO RUN ENGINE FOR 5 MINUTES.BECAUSE ITS HARD TO REMOVE OXYGEN SENSOR WHEN THEY ARE COLD. WEAR LONG SLEEVES AND GLOVES SO YOU WONT GET BURN BY EXHAUST PIPES YOU HAVE TO SAFELY RAISE VECHICLE SECURE ON JACK STANDS.YOU NEED A SLOT SOCKET MADE TO REMOVE OXYGEN SENSOR.YOU CAN IT AT ANY AUTO PARTS PLACES. YOU NEED A 3/8 RATCHET .ALL YOU DO IS DISCONNECT OXYGEN SENSOR WIRE LOOSEN SENSOR WITH THE SLOT SOCKET.REMOVE IT.REPLACE WITH NEW ONE.IF YOU NEED PHOTOS OF SENSORS YOU CAN BUY A HAYNES MANUAL

Jan 09, 2010 | 2004 Nissan Armada

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...