Question about Chrysler PT Cruiser

Open Question

2005 chrysler ptcruiser gt turbo how to change coil pack

How to change a coil pack

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2005 Pontiac grand prix 3.8 doesn't start

Try this: Turn ignition on for AT LEAST 10 minutes without doing anything else. After 10 minutes, turn the key to start, thre is a good chance of it running. Long explanation, but it has to do with the PassLock security system futzing up.

Posted on Dec 13, 2008

  • 1 Answer

SOURCE: 2000 GTI 1.8 liter turbo #3 coil pack swap!

Took the information that I found on the internet and ran with it. Once I got the part I looked at the engine after taking off the plastic cover on top of the engine it was self explanatory. I took a chance on how the pstons were numbered and it was right. The car runs great!

Posted on Jan 09, 2009

  • 216 Answers

SOURCE: How do I change the fuel filter on a 2006 2.4lt

your cars fuel filter is inside your fuel tank along with the fuel pump....you need to remove the back seat to give way in removing the top cover of the fuel tank that holds the fuel pump and filter...no need to drain the tank with its fuel...fuel filter replacement interval is every 20,000 km. or 12500 miles.

Posted on Apr 14, 2010

  • 878 Answers

SOURCE: My ptcruiser will not star.My

make sure the firing order is correct cause if not it will not start,you can go to local part store they give for free

Posted on Mar 22, 2011

  • 1 Answer

SOURCE: 1992 ford probe gt 2.2l

1989 ford probe turbo 2.2L turbo the oil filter sandwich block thats adapted to the block of the motor... the Hole that comes out block and from where the sandwich adapter mounts to the block... is there suppose be some sorta plug or fitting there? is there possible get detailed picture so i know what im missing?

i have hole and ******** oil out... and trying get fixed so i can sell the car... to fix my current problem no motor for a mustang 5.0 gt so if anyone can help me out id greatly apppericate it...

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

#1 and #4 are not firing I changed the coil pack and still no change any ideas


You said you changed the coil pack and the wires but didn't mention the plugs. Try moving one of the plugs to a different cylinder and see if the miss follows it. It could also be the ignition module. (the thing the coil packs mount to.)

Oct 05, 2012 | 1993 Chevrolet Lumina

1 Answer

Wont start in wet weather


the coil pack is a series of coils if he replaced the pack then all the coils were replaced. now the question is were they new or were they a junk yard part. try replacing the rotor under the distributer cap.

Mar 30, 2010 | 1997 Isuzu Hombre

1 Answer

1999 Isuzu amigo, code for cylinder 1 misfire.....changed plugs still missing.....what next?


coil pack or distibuter...if coil pack you will need to change the coil pack that # 1 wire is attached to

Mar 05, 2010 | 1999 Isuzu Amigo

1 Answer

I have a 2002 TrailBlazer with the straight 6,diognostic check said #3 cylinder was dead or misfiring, also map sensor showed up. #3 cylinder was misfiring, so to test the coil pack I swapped #3 coil pack...


did you replace only one spark plug? that can cause issues because of differences in resistances between cylinders. also, did the map code stay off after replacing
?

Feb 28, 2010 | 2002 Chevrolet TrailBlazer

2 Answers

Changed coil pack that wasnt firing started fine


check the fire to the coil pack if it's present then check the pulse to the crank sensor

Jan 14, 2010 | 1999 Pontiac Firebird

1 Answer

One of the coil packs is not working on a 3800 V 6


have you tried changing the coil pack? they are simply a coil of wires inside. they easily go bad. just to be sure switch one of the coil packs to make sure its not a problem with the wiring, if the problem switches cylinders replace the coil pack

Aug 28, 2009 | 2000 Chevrolet Camaro

2 Answers

Engine misfires


You didnt mention having changed the spark plug wires, so that is another item that could be culprit as well. As well, it could be a coil pack that is not working properly.

I cannot recall at the moment if that model year uses coil on plugs or if it uses coil packs. Either way, if it uses a coil on plug set up, take the one for the #3 cylinder and move it to say #4 or anyone of your choice and see if the misfire follows

If it uses coil packs, there is likely one coil pack that controls two cylinders. In that case just swap the coil pack with an adjacent one and see if the problem follows. Pay attention to where the spark plug wires go because it will be an issue if you get them mixed up. You just swap the coil packs around.

I would, however, start with the spark plug wires if you have not changed them already.

Dec 31, 2008 | 2003 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...