Question about Buick Lucerne

Open Question

After replacing rear shocks on 2008 Lucerne, how do i turn off the ceck rear suspension light

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnthejag
  • 286 Answers

SOURCE: my 1989 jag xj6. the rear suspension (shocks) are down

Hi Verbatum

Yes, replacing the self leveling rear shockers with gas shocks, is the way to go.

The self leveling system was notoriously problematic.

Due to either to the leveling sensor going faulty, and making the car go up and down, whilst sitting at the lights. ( Do not be surprised to see that yours has been disconnected. )
Other problems are loud knocks over the big bumps, and finally oil leaks from the shockers.

Yes Jaguar in there wisdom, did not make things easy, and new gas shockers will not match your old springs.

I do have all the Jaguar part numbers somewhere for this job, if you want to keep it all Jaguar.
( let me know and I will have a look !)

I have seen in the past, Modification Kits being offered in England, but would have to get back to you with source.

I see you are in Canada , and I am in Spain, and not familiar with your spares situation out there.

You will be requiring 2 Gas Shockers, 2 Springs and retaining collets, and plates.

I hope I have been of help.

Good Luck

John.


Posted on Jan 18, 2009

Ad
ancdlm
  • 58 Answers

SOURCE: The rear airbag suspension needs to be replaced.

I Would go with springs. I understand people enjoying the air ride but I promise it is more trouble than it is worth. Compressors have a 100% failure rate. What will happen is the airbag will end up getting a hole or tiny crack in it so the compressor has to work extra hard because it is like blowing up a balloon with a hole in it. Therefor the airbag kills the compressor and you have to parts you have to constantly keep buying. With air suspension there is never a permanent fix. I would recommend going to strutmasters.com and taking a look at the conversion kits. these convert you from the airbag to a powder coated American made steel coil spring that is [U][B]guaranteed[/B][/U] to last the life of the car. And for a very affordable cost. I added the link below so you can check it out.

http://www.strutmasters.com/buick-suspension-parts-s/27.htm

I hope I was of some help

Good Luck!!!

Posted on May 06, 2009

ancdlm
  • 58 Answers

SOURCE: 2003 Lincoln Navigator air suspension

I would recommend going to strutmasters.com and taking a look at our conversion kits. these convert you from the airbag to a powder coated American made steel coil spring that is guaranteed to last the life of the car. Airbags and compressors are constantly having to be replaced. Also something alot of people don't know is that theses air suspensions are not meant to be in temperatures above 90 Degrees or below 40 Degrees. That is most of the world. The temperature will cause you to replace alot of bags. and typically when your replacing a bag you are going to have to replace the compressor to because the bag had a hole or small crack in it causing the compressor to over work and it will die. I posted the link below so you can take a look http://www.strutmasters.com/lincoln-suspension-parts-s/1.htm I hope I was of some help Good Luck!!!

Posted on May 06, 2009

  • 28 Answers

SOURCE: 1998 seville sts check suspension light stays on.

that system has a pump, you should hear it run when you start the car. it also has a bleed valve. i have seen the valve get stuck before. i don't remember what year caddillac stopped putting the suspension switch in the trunk, but if the switch has been turned off the light will remain on as well. there is a level sensor under the rear of the car connected to the suspension you can try to disconnect the arm and manually move it and see if the pump kicks on. there is a few second delay before you hear the pump. if the fuses are good and the switch is on check for voltage at the pump when you move the level sensor. check for signal from the sensor. if pump runs and shock don't air up check for air leaks with soap water spray, and/or air bypassing valve. hope i helped you...dustang

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Buick lucerne 2008, the trunk light won't come on. I've checked the globe, it's good, not sure where the fuse is but there is no power to the globe. Where's the switch and which fuse do I check?


Rear Compartment Lamp
The BCM supplies battery positive voltage from the INT LAMPS fuse at all times through the inadvertent power courtesy lamps circuit to the rear compartment lamp. When the rear compartment is opened, the rear compartment lamp switch closes to ground and the lamp illuminates.

Feb 04, 2017 | 2008 Buick Lucerne

1 Answer

Where exactly is the switch for the air suspension compressor on a 2006 Buick Lucerne CXL?


The automatic level control (ALC) system maintains a desired rear suspension position under all types of towing, hauling, and loading conditions.
The system uses the electronic suspension control module (ESCM), ALC relay, ALC compressor assembly, air dryer, air lines, LR and RR shock absorbers with integral air chambers, LR and RR suspension position sensors, exhaust valve, driver information center (DIC), and the serial data circuit to perform the system functions.
What switch ? there are sensors at the wheels that control the system .
The system uses the automatic level control module (ALCM) with integral suspension position sensor, ALC relay, ALC compressor assembly, air dryer, air lines, LR and RR shock absorbers with integral air chambers, exhaust valve, driver information center (DIC), and the serial data circuit to perform the system functions.

The

Jul 10, 2016 | Buick Cars & Trucks

1 Answer

HOW TO REMOVE PASSENGER SIDE REAR TAIL LIGHT


From inside the trunk remove the cover on either side & you will have access to the holdown bolts for the taillights (behind the lens)

Sep 10, 2014 | 2008 Buick Lucerne CXL

2 Answers

Need to locate the air pump that supplies the rear shocks.


The pump is back under the rear of car, but by now, the shocks are sure to be leaking, which causes the pump to run too much burning it up. Best fix is to replace rear shocks with coils and dump the self leveling feature, or prepare to pay big bucks to replace most components.

Mar 30, 2014 | 1999 Cadillac DeVille

1 Answer

2007 Yukon Denali XL autoride suspension light comes on intermittently


Would need to know what DTC'S - diagnostic trouble codes are stored in the module for the autoride suspension . Hooking up a professional type scan tool ,looking at input data to the module etc... Looking at a wiring diagram an testing electrical circuit's using a DMM - digital multi-meter . Reading how the system works ,what all involved in making the system work . This is how a professional Tech would go about diagnosing this .

The automatic level control (ALC) system maintains a desired rear suspension position under all types of towing, hauling and loading conditions. The following components are involved in the operation of the ALC system:
• Air line tubing--Pressurized air from the ALC compressor is pumped to each of the rear shocks via air line tubing.
• Air drier--Pressurized air from the compressor is run through a drier containing a moisture absorbing chemical preventing water accumulation in the rear shocks.
• Compressor--Supplies pressurized air to the rear shocks
• Compressor motor relay--The relay supplies battery positive voltage to the ALC compressor motor.
• Pressure sensor--The electronic suspension control module (ESCM) module provides a 5-volt reference and low reference to the ALC pressure sensor. The module receives the signal voltage that is relative to the air pressure applied to the rear shocks.
• ESCM--Controls the ALC system and electronic suspension control (ESC) system and detects failures in both. The module monitors inputs from the position sensors, and pressure sensor to determine when to raise and lower the vehicle to trim height as the vehicle is loaded or unloaded. The module limits pump activation to 255 seconds to prevent thermal damage.
• Exhaust valve--An electric solenoid activated by the ESCM to vent air pressure from the rear shocks.
• Left and right rear suspension position sensors--The module provides a 5-volt reference and low reference to all 4 of the body-to-wheel suspension position sensors. The sensors send the ESCM a signal voltage that is relative to the rear suspension ride height
• Left and right rear shock absorbers with internal air chambers and dampers--Dampens the rear suspension and maintains trim height depending on the air pressure applied.

Nov 04, 2017 | 2007 GMC Yukon XL Denali

1 Answer

I was getting the "Check


Many times, lights will not turn off until a dealership turns them off. There may not a problem with the suspension anymore, but the light will stay on until the light turns off.

Apr 17, 2011 | Lincoln Navigator Cars & Trucks

2 Answers

How zerks to lube on 2008 lucerne?


There are no grease zerks.There is nothing to lube on your suspension.Most newer vehicle do not have grease zerks anymore.Hope this helps.Good luck.

Feb 09, 2011 | 2008 Buick Lucerne

2 Answers

2008 elantra suspension clunks in the rear


depending on mileage and relationship you have with your dealer, the rear struts may still be under warranty. 24,000 miles if i remember right. those are your issues. replace the rear struts. cheers

Jan 22, 2010 | 2008 Hyundai Elantra

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

2 Answers

Cannot locate the battery under the hood


The battery in my 2007 Lucerne is under the rear seat. Just pull up hard on the fornt of the rear seat bottom.

Feb 11, 2009 | 2008 Buick Lucerne

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...