Question about 1993 Chevrolet C1500

Open Question

What color wire makes the 4L60E shift

2000 gmc 4x4

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: trans change

no it will not sorry

Posted on Feb 12, 2009

Molson02536
  • 3854 Answers

SOURCE: 4L60E Shifts fine in 1st, 2nd, & 3rd but will not shift into OD

The EMC detected and problem so it's in limp mode, As long as it's in limp mode the 4th and OD will not activate. Take care not to burn up the transmission by running it hard while your in the limp mode.
Your going to have to get the truck scanned to clear any codes and why there are DTC codes. Auto Zone scan for free and most auto shops charge $10.00 to $20.00 to scan sine they want the business.
If you want to clear the codes your self you can put the ignition to the run position and pull the ECM (Batt) fuse out for 20 sec and place it back in then start the truck. It may stall but let it, just start it again and this would have cleared all the DTC code history.
The transmission should be running fine unless there is a problem and the service engine light will be on again and you'll be in limp mode still with an updated DTC in the ECM.
Good luck and hope this helps.

Posted on May 26, 2009

  • 232 Answers

SOURCE: a buddy brought me his headache.Its a 1994 GMC

Get the correct TCM.

Posted on Jun 03, 2009

  • 4 Answers

SOURCE: 94 gmc ex-cab 4l60e

the transmissions should be the same, however the tail shafts are different lengths. The can be switched between the 2 trans.

Posted on Jun 19, 2009

  • 61 Answers

SOURCE: 99 3500 4x4 350 4l60e won't shift past 2nd gear.

This is a very common problem. First off, is the trans just going neutral when it attempts to shift to 3rd? If so, most likely the 3-4 clutches are burnt up. If it is not attempting to upshift, may be electrical. Check the condition of your fluid, if it smells burnt, or is discolored, this is an indication of internal failure, you can also remove the pan, and check for contamination. Should also have the truck checked for codes, this can be done for free at Auto Zone. But been my experience, once you lose 3rd and 4th, most likely culprit is the 3-4 clutches, at which point you will need some type of overhaul.

Posted on Dec 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix automatic transmition in 2002 GMC ENVOY 4x4 shifts hard into third will not shift into overdrive already replaced the two solenoids in front before it would not shift to third


How To Rebuild A 4L60E Automatic Transmission - YouTube

? 13:19
https://www.youtube.com/watch?v=JpmJtuVrdWk
Mar 16, 2011 - Uploaded by Nick Stageberg
How To Rebuild A 4L60E Automatic Transmission ... Also here is a link to some common break/fixes that may require a rebuild:... GMC canyon, envoy, safari savana, sierra Sonoma, Yukon, ....Great video, my 96 sierra 4x4 when shifting into high gear motor races as if nothing is there........................always ...

30 Common 4L60E Transmission Problems & Repair ...

www.twincharlotte.com/transmission-repair.../30-Common-4L60E-Trans...
Mar 18, 2011 - The 4L60-E is an automatic shift, four-speed overdrive, longitudinally...... 4l60e 2002 gmc 4x4 was not driven for 1 year,will not shift into 3rd or ... I have a 2005 GMC envoy 4x4 6 Cylinder I assume it is a 460LE Transmission.

Nov 24, 2015 | GMC Cars & Trucks

1 Answer

Transmission will only shift in 4 low,no codes showing


1994 GMC 4l60e transmission shifting problems - CarGurus

www.cargurus.com > Questions > GMC > Sierra 1500
CarGurusJan 17, 2011 - 1994 GMC 4l60e transmission shifting problems - I've got a 1994 GMC Sierra 4X4 5.7 I ... If you put it in low and lift the handle, it will go into second .... Justchange 1-2 - 3-4 solenoids first and if that doesn't work change the ...

Troubleshoot automatic transmission problems

www.2carpros.com/articles/automatic-transmission-problems
Jul 15, 2015 - Rescan the PCM for trouble codes, if none appear the problem could ...Excessively low transmission fluid (Note: If transmission is operated for an .... it waslow, and now my car will only shift from 1st to 2nd manually and will ...

Nov 03, 2015 | Cars & Trucks

1 Answer

1998 gmc 4x4 5.7 replaced transmission now truck won't start it has a 4l60e transmission weak yellow spark to the plugs


hook up a scanner check for engine codes, if no codes hook up fuel pressure gauge, make sure all you wiring harnesses got reconnected underneath the vehicle

Oct 13, 2015 | GMC Cars & Trucks

1 Answer

I have a 2000 gmc sierra with 5.3 engine and 4l60e transmission and it won't down shift or respond to wot


Take to a trans or repair shop

You can not guess at all the possible
issues on a vehicle,have to look at data,
wiring diagrams & do some testing

Jul 17, 2014 | Cars & Trucks

1 Answer

2000 gmc 4x4 it will not shift into 3rd gear or overdrive


There is a 3/4 clutch pack in the trans that when it fails you loose those two gears. There is nothing you can do other than to pull the trans and do an overhaul . I started rebuilding those back in 1982 when they first came out in the old 700r4. Even though the new 4L60E is all computer controlled, it is still doing the same thing.

If you tow with it and do not push the tow/haul button it will burn the clutches, especially if you are towing a large heavy load.

Sorry for the bad news

Apr 09, 2010 | 2000 GMC New Sierra 1500

1 Answer

I have 1995 GMC Jimmy with codes PO753 and 758. These mean power problem to Transmission solenoid A and solenoid B. The fuse is blown and pops again when replaced so I know that a short must be present but...


Possible for the solenoid to be the fault, swap the shift solenoids and see if the problem moves, if not check wireing harness for bare wire.

Sep 19, 2009 | 1995 GMC Jimmy

2 Answers

95 GMC Sierra 4L60E will not shift down to 1st or up to 4th.


no power stuck in 3rd gear electric shop unless youve burnt it up good luck...www.TransmissionGarage.com

Jan 28, 2009 | 1995 GMC Sierra

2 Answers

Where is my 1 2 shift sensor 2000 gmc jimmy


Inside trans. pan at the rear of the valve body. They have a wire clip which holds them in.

Jan 21, 2009 | 2000 GMC Jimmy

2 Answers

1995 GMC 2500 4x4 wont shift into 3rd or overdrive most of the times


i have heard that the ignition switch can be faulty and not let the full voltage thru to the electricaly controlled 4l60e trans.i have the same problem with my 95 1/2 t. i rigged a switched wire from the fuse block via a relay to the proper wire on the trans....ask a trany tech and they will know what im talking about,,,good luck

Oct 23, 2008 | 1995 GMC Suburban

Not finding what you are looking for?
1993 Chevrolet C1500 Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...